SoundTube SS-Q-8 Handleiding
Pagina's 2 Speaker
Bekijk de handleiding van SoundTube SS-Q-8 gratis online of download de PDF. Deze handleiding is 4 keer bekeken. Vraag over dit model? Stel een vraag
SS-Q-8
OWNER’S MANUAL
© 2021 MSE Audio. Rev. 05.07.2025
Please read the following instructions carefully before installing
your Soundsphere
®
speaker. If you have any questions
regarding installation that are not answered in the following
directions, please contact your local sound contractor or the
SoundTube® technical support team.
General Information
Maximum Amplier Power 100 Watts RMS
Nominal Impendance 8 ohms
Wiring
Amplier connection is via ying leads. Connect the positive
(+) amplier lead to the RED input wire. Connect the negative
(-) amplier lead to the BLACK wire. Secure connections us-
ing wire nuts, etc. For wiring optional 100W transformer, see
section “SS-TX100 Transformer Installation Instructions” on
page 2 of this manual.
Mounting
Hanging Kit
Mount using one of the following methods:
a) Properly secured wire rope with a minimum breaking
strength of 225 lbs. (for a 10:1 safety factor).
b) Beam clamp with proper load rating.
It is recommended to use a secondary wire rope support around
one of the SS-Q-8 legs. Do not use rope for mounting. The use
of chain is not recommended unless rated for suspension of
loads greater than or equal to 225 lbs (for a 10:1 safety factor).
Surface Mount Bracket
Secure the bracket to the hard surface using proper hardware.
Secure the SS-Q-8 to the bracket using the washers and nylon
locknuts provided. It is recommended to use a secondary wire
rope support around one of the SS-Q-8 legs and through an
unused bracket hole.
Replacement Parts
8” 100 Watt coaxial loudspeaker driver with crossover.
- Order Model Number SS-CX8
Always check local requirements for overhead suspension
of loudspeakers.
Replacing the Coax Driver and Crossover in the SS-Q-8
1. Remove the reector from the SS-Q-8 by removing the 3
bolts, washers, and tabs.
2. Remove the 4 screws securing the driver. Remove the
driver by gently lifting the tweeter with one hand and
removing it with the other hand. Pull the wire out through
the hole in the bolt.
3. Feed the wire from the replacement driver through the
drilled bolt inside the sphere. Install the new driver and
secure with screws.
Other Information
Wire runs between the amplier(s) and loudspeaker(s) must be
of the appropriate gauge to insure the full audio performance
capabilities of the Soundsphere loudspeakers. This applies
to all loudspeaker impedances (4 or 8 Ohms) or audio line
voltages (50, 70.7 or 100 Volts). For more information, please
see the ‘Downloads” section at www.soundtube.com, or call
our Customer Service at 913.663.5600.
Leg Bolt
Tab
Metal Washer
Rubber Washer
Reector
Rubber Washer
Metal Washer
Leg
© 2026 SoundTube Ent. Rev. 07.27.2026
360º of the Best Sound Around™
Contact: SoundTube, 855.663.5600 / 913.663.5600 / sales@soundtube.com
by
WARNING
Be sure to securely tighten all hardware before hanging the loudspeaker. Wire rope (steel cable), cable clamps with saddles and
thimbles of suitable size and strength are the recommended materials for overhead suspensions. All loudspeakers should be safety
wired to structural members of the building with an approved safety wire system or other agency certied materials.
IMPORTANT:Always check local safety codes before installing any overhead loudspeaker system and for periodic
inspection and maintenance of the installation.
Product specificaties
| Merk: | SoundTube |
| Categorie: | Speaker |
| Model: | SS-Q-8 |
Heb je hulp nodig?
Als je hulp nodig hebt met SoundTube SS-Q-8 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden