Soundstream Reserve SG-V2 Handleiding
Pagina's 34 Autoradio
Bekijk de handleiding van Soundstream Reserve SG-V2 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
LIMITED FIVE-YEAR (5-YEAR) CONSUMER WARRANTY WITH PURCHASE FROM
AN
AUTHORIZED SOUNDSTREAM AND/OR PRECISION POWER RETAILER
RESERVE
Epsilon Electronics Inc. promises to the original purchaser
of
this product to repair to like-new condition
or
replace this product with a new
or
like-new unit (at Epsilon Electronics' sole and absolute discretion),
by
seUNDSTREAM
should it prove to be defective in workmanship or material under normal use, for a period
of
five-years
(5-years) from the date
of
purchase from a Soundstream and/
or
Precision Power authorized retailer.
During this five-year (5-year) period, there will be no service charge for repair
or
replacement.
DEM
UPGRRUE
IIERU
UNIT
FUR
This limited warranty extends only to the original purchaser
of
the product, and it is not transferable to
the next owner
or
purchaser
of
the motorcycle into which the product was originally installed. This
warranty does not cover labor costs for removal and reinstallation
of
the produc
t.
This warranty is void
if
the product has been damaged caused by installation
or
removal
of
the product
and will not apply to any unit that is determined to have been modified
or
mis-used in a manner contrary
l
to its intended purpose. This warranty is void
if
the product has been damaged by accident or
unreasonable use, ne
gl
ect, improper service or other causes not arising out of defects in material,
construction, or workmanship. This warranty does not include the elimination
of
externally generated
static or noise,
or
the correction
of
antenna problems or weak reception, damage to speakers,
accessories, electrical systems, cosmetic damage
or
damage due to negligence, misuse, failure to
foll
ow
operating instructions, accidental spills
or
customer applied cleaners, damage due to
environmental causes such as floods, airborne fallout, chemicals, salt, hail, lightning
or
extreme
temperatures, damage due to traffic accidents, road hazards, fire, theft, loss
or
vandalism, damage due
to improper connection
to
equipment of another manufacturer
or
modification
of
existing equipment.
To file a warranty claim, please contact Soundstream's warranty office to obtain a Return Authorization
number prior to shipping the product:
Phone: 1-800-724-1377
Epsilon Electronics Inc.
E-mail: repairs@soundstream.com
1550 South Maple Ave
Website: soundstream.com/warranty
Montebello,
CA
90640 USA
After receivi
ng
the RA number, pack the product into suitable packaging, include dated proof
of
purchase, (i.e. a receipt
or
bill
of
sale) from the authorized retailer and a money order
or
cashier's check
for return freight to Epsilon Electronics' corporate office, addressed above. Please clearly write the
RA
number on the outside
of
the packaging.
IN ORDER FOR THE FIVE-YEAR (5-YEAR) WARRANTY TO BE VALID,
THE
PRODUCT MUST BE
SHIPPED WITH PROOF OF PURCHASE FROM
AN
AUTHORIZED SOUNDSTREAM AND/
OR
PRECISION POWER AUTHORIZED RETAILER. ANY PRODUCT RECEIVED BY SOUNDSTREAM
FOR WARRANTY WITHOUT AN
RA
NUMEBR AND PROOF
OF
PURCHASE FROM A
SOUNDSTREAM AND/OR PRECISION POWER AUTHORIZED RETAILER WILL BE REFUSED. BY
PURCHASING THIS PRODUCT, ALL WARRANTIES INCLUDING BUT
NOT
LIMITED TO EXPRESS l
WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR
PARTICULAR PURPOSE, AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL
PROPERTY ARE EXPRESSLY EXCLUDED TO THE MAXIMUM EXTENT ALLOWED BY LAW.
SOUNDSTRE
AM
NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY
LI
ABILITY IN CONNECTION
WI
TH THE SALE OF THE PRODUCT. SOUNDSTREAM HAS
ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING ITS
AUTHORIZED RETAILERS OR INSTALLERS. BY PURCHASING THIS PRODUCT, THE
CONSUMER AGREES AND CONSENTS THAT ALL DISPUTES BETWEEN THE CONSUMER AND
SOUNDSTREAM SHALL BE RESOLVED IN ACCORDANCE WITH CALIFORNIA
LAWS
IN LOS
ANGELES COUNTY, CALIFORNIA. Some states do not allow limitation on how long an implied
warranty lasts. In such states, the limitation
or
exclusions
of
this Limited Warranty may not apply. Some
states do not allow the exclusion
or
limitation
of
incidental
or
consequential damages. In such states,
the exclusion
or
limitation
of
this Limited Warranty may not apply to you. This Limited Warranty gives
you specific legal rights, and you may have other rights which vary from state to state.
"YB-"13
IIRRLEY-DRI/IDSDN
® ELECTRR
GLIDE
@
UL
TRR
®
.,
Ii
STREET
GLIDE
® MDTURCYCLES
INSTRLLRTIDN
GUIDE
A;p
le
Ca
r
Play
(
androida
uto
J
Z-OHM
4<h.SP€AKER
AMPU~IER
'-"
maestro
CD
M P
.\
Tl
ll
l
WidE
.•.
((<
Siriusxm
>))
Wi
rEIESS
@
··
scrEEn
HEadsEt V
READY
lntGf)ratlon
L
CD
/5-BAND
5-VOLT
/PxS
• • • • 1
RCA AUDIO
WATERPROOF I t
:-r:Jlf~~RS
---I
·~
OUTPUT ~
FACEPf.ATE
TO
PRINT A COMPLETE OWNERS MANUAL, VISIT
US
ONLINE
AT
MOTORCYCLEAUDIO.COMISGV2
-OR-
SCAN
THIS QR CODE WITH YOUR PHONE'S
CAMERA
TO
DOWNLOAD THE COMPLETE
OWNERS MANUAL
TO
YOUR PHONE.
Remn11ill
nr
the
Filirina
Ii
Uriainill
UeiJd
Uni
t
To
prevent
accident
al
vehicle
start
-
up
,
which
could
ca
use
death
or
se
ri
ous i
nju
ry, re
mo
ve
mai
n
fuse be
for
e
proc
ee
ding.
1.
Remove four fairing screws holding the outer fairing to the
inner fairing using a T27 Torx driver. The first two screws are
located under the fairing adjacent to each fork:
Tip: Turn the handle
bar
for better access to
the screws.
The second pair
of
screws are below/adjacent
to each speaker:
2.
Remove three screws that attach the windshield &
outer fairing to the inner fairing using a T27 Torx driver.
Remove the windshield & set aside. Reinstall the center
screw
by
hand to hold the outer fairing in place. Set
remaining screws aside for installation later.
3. While straddling the front wheel fender, grasp the outer fairing.
Remove the center windshield screw. Gently pull the fairing
apart from the bike. With the fairing slightly pulled away from the
bike, disconnect
wire
harness for the headlight
or
any other acces-
sories. Lay the fairing on a protected flat surface to prevent
damage.
4. Disconnect all wire harnesses from the OEM radio. Use a
pry tool, flat-heat screwdriver,
or
pick tool to lift
up
on the locking
tab, then pull the male connector(s) out from the female
connector(s). Also, unplug the
FM
antenna & disconnect the CB
antenna (if equipped).
If
the OEM SiriusXM tuner
is
installed,
disconnect
& remove its antenna,
it
will not be used.
RemDl'iJI
nr
the
Filirina
Ej
Uriainill
UeiJd
Unit
(c
ant
.I
5. Remove the OEM head unit
by
removing 4 screws from the head
unit support bracket. Use a 3/16"
hex/alien key tool
to
remove 2
screws from each side. An access
hole
in
the
fa
iri
ng
support brackets
accommodates a hex/alien tool.
Set these four screws aside for
reinstallation.
6.
Gently pull the OEM radio out and up, away from
the
support
bracket. No other parts from the OEM radio are needed.
7.
Take a momentto clean the surfaces of the inner fairing surrounding
the cutout for the radio & around the rectangle recess using a damp
micro-fiber cloth. Any debris
or
residue left on these surfaces can
affect the water-tight seal around SG.V2.
lnstilllilfinn
nr
St:.
112
UeiJd
Unit
1. The ignition switch needs to be removed for initial installation. Turn the
handlebars to the far left, then turn the ignition switch counterclockwise
to FORK LOCK.
2. Insert the key & press the unlock pin under the switch, on the left
side. While pressing the unlock pin under the switch, turn the key
counterclockwise slightly beyond the UNLOCK position.
3.The ignition swit
ch
should be free. Remove the ignition switch with
spring and set aside.
If
available, insert an ignition alignment tool
while proceeding to the next step.
4. Route the USB cable, antenna extension,
& RCA camera input
w/ trigger thru the cutout
of
the inner fairing. Pull the chassis
of
SG.V2
thru the rectangular recess, aligning the mounting screw holes with
holes
of
the fairing support bracket.
If
used, the ignition alignment tool
may need to be removed momentairly while installing the head unit.
5. Secure SG.V2 to the radio support
bracket with the 4 screws set aside
during removal
of
the original head unit
(step 5) using the same hex/alien key tool.
lnsfilllilfian
ar
SC.
l/2
ll~ild
Unit
rmn,1
6.
Insert and lock the male OEM head unit wire harness
connector(s) to the female socket(s)
of
the included wire
harness. Then, insert and lock the male connector
of
the
included wire harness into the corresponding female socket
on the back
of
the SG.V2. Swivel the latch into place,
locking the male connector into the female receptacle.
7. Identify the location you wish to have the
wired
CarPlay/An-
droid Auto USB connector. Drill a hole at the location using a
13/16"
or
7/8" spade bit
or
step bit. Route the USS cable from the
head unit to the USS location.
8. Remove the USS port cap, unthread the plastic nut and remove the gasket
for the USS port cap. Be sure the secondary gasket ring remains. Insert the
threaded end
of
the USS port thru the hole drilled during the previous step.
Slip the gasket ring of the USS port cap over the threaded USB port. Thread
the plastic nut down the USS port to secure
it
to the fairing surface. Finally,
reatta
ch
the USB port cap.
9.
Connect t
he
AM/FM radio antenna to the female receptacle extension, and any accessory added to this
installation; SiriusXM tuner, Bluetooth calling microphone, camera video-
in
& trigger, GPS antenna, etc.
If
any afternarket audio amplifiers will be used
in
the audio system, take a moment to connect the RCA
cables to the corresponding audio outputs. Although not required,
if
th
e Bluetooth calling microphone will
be used, secure
it
to
the
desired installation location, then route its cable to the corresponding input on the
back of SG.V2.
•
T_.c
Coonecta<
ro,
fa.st
Charging
Type-A
Connector
fa<
USB
playback
RCA Low-Level Rear Channel Output
for Optional Speaker
Ampl1t1er
(RCA not incl.}
RCA Low-Level Subwoofer Channel Output
fa<
Opoooaf Subwooler Amp! l
ier
(RCA
not
incl.)
---~
C e I (
Radio
Antenna
Optional camera 'owe<, 12V/05A
(pinl<)
amera
Vdeo-i"'
1nd,cator
Light
Conneuor
Bluetooth
Antenna
l
I
j
10
. Insert and lock the male OEM head unit wire harness connector to the female socket
of
the included
wire harness for SG.V2. Then, insert and lock the male connector
of
the SG.V2 wire harness into the
corresponding female socket on the back
of
SG.V2.
~
O
EM
wire
ha
rness
CoMector B
Conn
ect
or
A
~
lffli~I
~
Connector B ConnectorC
Note:
If
this installation does
not
include
an
iDataLink
Maestro
RR
module, disconect
the
small
handlebar
interface chip from the wire harness
and
attach
connector B
to
the unused
connector
A.
Connector
C
will
not
be
used.
11
. Visit www.idatalinkmaestro.com to
program your RR2 before installation.
Afterwards, attach the 3 black and 1 green
color connectors found on the wire
harness for
SG
.V2 to the corresponding
female socket found on the RR2 module.
Each connector is different size with keyed
edges & locks so they
will
only install in the
correct location.
■
I
@maestro
I
Product specificaties
| Merk: | Soundstream |
| Categorie: | Autoradio |
| Model: | Reserve SG-V2 |
Heb je hulp nodig?
Als je hulp nodig hebt met Soundstream Reserve SG-V2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden