Sonic Alert HA360SSSC Handleiding

Bekijk gratis de handleiding van Sonic Alert HA360SSSC (2 pagina’s), behorend tot de categorie Beveiliging. Deze gids werd als nuttig beoordeeld door 97 mensen en kreeg gemiddeld 4.2 sterren uit 4 reviews. Heb je een vraag over Sonic Alert HA360SSSC of wil je andere gebruikers van dit product iets vragen? Stel een vraag

INSTALLATION AND SETUP FOR HOMEAWARE™ TRANSMITTER

HA360SSSC – Smoke / CO

The HomeAware™ Smoke/CO transmitterwill alert you to the

sounds produced by the smoke and CO detectors already

installed in your home. This transmitter alerts you through the

HomeAware™ Main unit and remote receivers located in

other rooms.

Battery Backup Installation

Install a new 9 volt alkaline battery into the battery

compartment located on the back of the unit. See diagram for

battery door location.Battery backup will provide power

when a power outage has occurred. Power will be provided

for a continuous outage lasting7 days, or for short outages

up to two years.

Link Button Set Up

This procedure will link your transmitterto your Main unit.

The Main unit will also provide an alert to all HomeAware™

remote receivers. When using the Bridge unit HA360BU all

original Sonic Alert receivers (SA101, SA201, BL300, and

SB1000) will also alert you.

It is best to do the link procedure in the same room with the

HomeAware™ Main unit, make sure the unit is plugged in.

To link a transmitter to your HomeAware™ Main unit:

1.Press set up button and the word LINKwill be shown on

the display, press Enter. LINKwill begin blinking.

(If LINKmode is entered by accident, simply press the

BACKbutton to exit and return to the clock.)

2. Press and hold down the Link button on the back of your

transmitter for about 1 second. The red LED on the

transmitter will light up. Release the button.

3. Upon successful connection, the red LED on the

transmitter will flash 2 times, then turn off. The

HomeAware™ main unit will briefly show DONE, and

return to the time display. Your transmitter is now

connected and ready to test and use.

Detecting the Different Alert Sounds

This transmitterdetectsloud sounds and will alert you to the

source of that sound.

When a sound is detected from the HA360SSSC it will send a

signal to the HomeAware™ base unit and all HomeAware™

remote receivers, also the red LED light will flash on the front

of the unit.

If this transmitter detects a loud sound from a smoke detector

that meets the T3 standard used for SMOKE DETECTORS,

“SMOKE” will scroll on the displayof the HomeAware™ Main

Unit.

(The T3 standard is on for 0.5 sec, off for 0.5 sec, repeated 3

times, and followed by 1.5 sec ofsilence, as defined by NFPA

code 72.)

If the transmitterdetectsa loud sound from a CARBON

MONOXIDE (CO) DETECTOR that meets the T4 standard,

“CO” will scroll on the displayed of the HomeAware™ Main

Unit.

(The T4 standard is on for 0.1 sec, offfor 0.1 sec, repeated 4

times, and followed by 5 sec silence, as defined by NFPA

code 720.)

For All Other Sounds

If a loud sound is detected that does NOT match the T3 or T4

standard, then “ALERT” will scrollon the HomeAware™ Main

unitin a loud, repeating pattern.

You can control the sensitivity level for the "ALERT" detection

using the switch on the back of the unit. There are three

levels to choose from: The HIsetting is the most sensitive

setting and will alert you to more sounds. Moving this switch

to MEDmakes it less sensitive and will alert youto less

sound. TheLOsetting is the least sensitive. If you’re not

picking up the sound you need to be alerted to simply move

the sensitivity switchto a higher setting. If you have set this

setting to HI and you are still not picking up the sound, try

moving the transmitter closer to the sound.

Power Input

The HomeAware™Smoke/COtransmitteruses an included

12V DC power adapter. Plug the power adapter into an 120V

AC power outlet, then plug the other end into the Low Voltage

12V DC input on the left side of the unit as show in the

diagram.

Product specificaties