SilverStone XE02-SP5 Handleiding
SilverStone
Hardwarekoeling
XE02-SP5
Bekijk gratis de handleiding van SilverStone XE02-SP5 (2 pagina’s), behorend tot de categorie Hardwarekoeling. Deze gids werd als nuttig beoordeeld door 2 mensen en kreeg gemiddeld 4.8 sterren uit 1.5 reviews. Heb je een vraag over SilverStone XE02-SP5 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/2
Figure 1 Figure 2
Figure 3 Figure 4
Take out the heatsink from its packing box. Before installing the heat sink, please check that heat sink must be properly
oriented to the system cooling air flow direction (Figure 1 & Figure 2).
1.
XENON (XE) SERIES – Assembly Guide for
AMD Socket SP5 Coolers
Remove the protection cover of thermal interface material (TIM) or thermal grease. The required amount of TIM has
been pre-applied on the bottom of the heat sink. Inspect pre-applied TIM for any damage.
Place the heat sink directly on top of the CPU (Figure 3) so that the six heat sink mounting screws are aligned with and
seated on the six heat sink mounting studs or nut standoffs on the socket stiffener frame. The heat sink must be
properly oriented to the system cooling air flow direction. Please note that the heat sink cooling fan should not be
attached to the heat sink body when tightening the six heat sink mounting screws.
Use a screwdriver with Torx T20 bit and adjust the screwdriver torque setting to 12.5~15.0 kgf-cm (10.8~13.0 lbf-in).
Before turning on the screwdriver, make sure that the screwdriver bit is fully engaged in the cavity of the heat sink
mounting screw head. Keep heat sink mounting screw vertical during installations.
Tighten the two diagonal heat sink mounting screws, i.e. the #1 and #2 screws (Figure 4) completely tighten screws
one-at-a-time Then do the same with the remaining four diagonal heat sink mounting screws.
2.
3.
4.
5.
1
3
2
4
5
6
1
3
2
4
5
6
SYSTEM COOLING
AIR FLOW
DIRECTION
SYSTEM COOLING
AIR FLOW
DIRECTION
NO.5 SCREW
NO.2 SCREW
NO.4 SCREW
NO.3 SCREW
NO.6 SCREW
NO.1 SCREW
Figure 5 Figure 6
6.
7.
8.
Follow the diagonal installation pattern on all six heat sink mounting screws to ensure that the bottom of the heat sink is
properly seated on the CPU and to prevent the heat sink from tilting.
For XE04 series, adjust the screwdriver torque setting to 5.0~4.0 kgf-cm (4.3~3.5 lbf-in).install the heat sink cooling fan
and holder assembly on the heat sink body and then tighten the single locking screw on top of the fan holder (Figure 5
& Figure 6).
Connect cooling fan connector to the fan header labeled for CPU on the motherboard.
1. Product component defects or damages resulted from defective production is covered under warranty.
Defects or damages with the following conditions will be fixed or replaced under SilverStone Technology’s
jurisdiction.
a) Usage in accordance with instructions provided in this manual, with no misuse, overuse, or other
inappropriate actions.
b) Damage not caused by natural disaster (thunder, fire, earthquake, flood, salt, wind, insect, animals, etc…)
c) Product is not disassembled, modified, or fixed. Components not disassembled or replaced.
d) Warranty mark/stickers are not removed or broken.
Loss or damages resulted from conditions other than ones listed above are not covered under warranty.
2. Under warranty, SilverStone Technology’s maximum liability is limited to the current market value for the
product (depreciated value, excluding shipping, handling, and other fees). SilverStone Technology is not
responsible for other damages or loss associated with the use of product.
3. Under warranty, SilverStone Technology is obligated to repair or replace its defective products. Under no
circumstances will SilverStone Technology be liable for damages in connection with the sale, purchase,
or use including but not limited to loss of data, loss of business, loss of profits, loss of use of the product
or incidental or consequential damage whether or not foreseeable and whether or not based on breach of
warranty, contract or negligence, even if SilverStone Technology has been advised of the possibility of
such damages.
4. Warranty covers only the original purchaser through authorized SilverStone distributors and resellers and
is not transferable to a second hand purchaser.
5. You must provide sales receipt or invoice with clear indication of purchase date to determine warranty
eligibility.
6. If a problem develops during the warranty period, please contact your retailer/reseller/SilverStone
authorized distributors or SilverStone
. http://www.silverstonetek.com
Please note that: (i) You must provide proof of original purchase of the product by a dated itemized receipt;
(ii) You shall bear the cost of shipping (or otherwise transporting) the product to SilverStone authorized
distributors. SilverStone authorized distributors will bear the cost of shipping (or otherwise transporting) the
product back to you after completing the warranty service; (iii) Before you send the product, you must be
issued a Return Merchandise Authorization (“RMA”) number from SilverStone. Updated warranty
information will be posted on SilverStone’s official website.
Please visit for the latest updates.http://www.silverstonetek.com
Warranty terms & conditions
Warranty Information
电机组件
金属结构件
塑胶结构件
线缆/ 连接器
介质/其它
包装材料
辅助材
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
NO.G11248230
○：表示该有毒有害物质在该部件
所有均质材料中的含量均在GB
/T 26572 规定的限量要求以下。
本表格依据SJ/T 11364的规定编制
×：表示该有毒有害物质至少在该部
件的某一均质材料中的含量超出
GB/T 26572 规定的限量要求。
Additional info & contacts
This product has a limited 1 year warranty in North America and Australia.
For information on warranty periods in other regions, please contact your reseller or SilverStone
authorized distributor.
本产品自购买之日起，于中国地区（不包含澳门，香港特别行政区）享有一年有限责任保固（部分产品
为二年，三年或五年）。详细保固年限请参照官方网站 www.silverstonetek.com.cn 公布之产品型号为
依据。
For North America (usasupport@silverstonetek.com)
SilverStone Technology in North America may repair or replace defective product with refurbished product
that is not new but has been functionally tested.
Replacement product will be warranted for remainder of the warranty period or thirty days, whichever is
longer.
All products should be sent back to the place of purchase if it is within 30 days of purchase, after 30 days,
customers need to initiate RMA procedure with SilverStone Technology in USA by first downloading the
“USA RMA form for end-users” form from the below link and follow its instructions.
http://silverstonetek.com/contactus.php
For Australia only (support@silverstonetek.com)
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and
the failure does not amount to a major failure.
Please refer to above “Warranty terms & conditions” for further warranty details.
SilverStone Technology Co., Ltd. 12F No. 168 Jiankang Rd., Zhonghe Dist., New Taipei City 235 Taiwan
+ 886-2-8228-1238 (standard international call charges apply)
For Europe (support.eu@silverstonetek.de)
For China (support@silverstonetek.com.cn)
For all other regions (support@silverstonetek.com)
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
Product specificaties
| Merk: | SilverStone |
| Categorie: | Hardwarekoeling |
| Model: | XE02-SP5 |
Heb je hulp nodig?
Als je hulp nodig hebt met SilverStone XE02-SP5 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Hardwarekoeling SilverStone
13 Mei 2025
13 Mei 2025
1 Mei 2025
1 Mei 2025
1 Mei 2025
1 Mei 2025
1 Mei 2025
1 Mei 2025
1 Mei 2025
16 April 2025
Handleiding Hardwarekoeling
- Iceberg Thermal
- Intel
- PCCOOLER
- FSP
- Scythe
- NZXT
- Cougar
- AZZA
- Cryorig
- Middle Atlantic
- Geometric Future
- Akasa
- Bitspower
- Sharkoon
- In Win
Nieuwste handleidingen voor Hardwarekoeling
15 Juni 2025
9 Juni 2025
3 Juni 2025
2 Juni 2025
2 Juni 2025
2 Juni 2025
20 Mei 2025
20 Mei 2025
20 Mei 2025
