Shimano CT-S510 Handleiding
Shimano
Fietsaccessoire
CT-S510
Lees hieronder de 📖 handleiding in het Nederlandse voor Shimano CT-S510 (1 pagina's) in de categorie Fietsaccessoire. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/1
Technical Service Instructions
General Safety Information
This product cannot be used with coaster brake-type products.
This product is for single front chainwheels only.
Periodically clean the chain tensioner and lubricate the pulley.
If there is a large amount of play in the pulley and an abnormal amount of
noise is generated while riding, replace the pulley unit.
Do not disassemble the pulley unit.
If the tension applied is too strong, noise may be generated while riding.
If the chain becomes elongated and excessive looseness occurs, readjust the
chain tension.
Parts are not guaranteed against natural wear or deterioration resulting from
normal use.
For any questions regarding methods of handling or maintenance, please
contact the place of purchase.
NOTE:
Chain Chain tool
Reinforced
connecting
pin
9-speed super narrow
chain such as
CN-7701/ CN-HG93
8- /7-/ 6-speed narrow
chain such as
CN-HG50/ CN-IG51
Silver
6.5 mm
Black
TL-CN31/
TL-CN22
TL-CN31/
TL-CN22
and
TL-CN30/
TL-CN21
Sprocket
CS-S500
18T/20T
(t = 2.0 mm)
16T – 23T
(t = 2.3 mm)
End pin Link pin Reinforced connecting pin
Move
Upward
direction
Downward
direction
Use neutral detergent to clean the chain. Do not use alkali-based or acid-
based detergents such as rust cleaners, as they may result in damage
and/or failure of the chain.
Use the reinforced connecting pin only for connecting the narrow type of
chain.
There are two different types of reinforced connecting pins available. Be
sure to check the table below before selecting which pin to use.
If connecting pins other than reinforced connecting pins are used, or if a
reinforced connecting pin or tool which is not suitable for that type of
chain is used, sufficient connection force may not be obtained, which
could cause the chain to break or fall off.
If it is necessary to adjust the length of the chain due to a change in the
number of sprocket teeth, make the cut at some other place than the
place where the chain has been joined using a reinforced connecting pin
or an end pin.
The chain will be damaged if it is cut at a place where it has been joined
with a reinforced connecting pin or an end pin.
Check that the tension of the chain is correct and that the chain is not
damaged.
If the tension is too weak or the chain is damaged, the chain should be
replaced. If this is not done, the chain may break and cause serious
injury.
Obtain and read the service instructions carefully prior to installing
the parts. Loose, worn, or damaged parts may cause serious injury to
the rider.
We strongly recommend only using genuine Shimano replacement parts.
Read these Technical Service Instructions carefully, and keep them in a
safe place for later reference.
WARNING – To avoid serious injuries:
Be sure to read these service instructions in conjunction with the service
instructions for the internal 7-speed /8-speed hubs before use.
Chain length
One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003
Industrieweg 24, 8071 CT Nunspeet, The Netherlands Phone: +31-341-272222
3-77 Oimatsu-cho, Sakai-ku, Sakai, Osaka 590-8577, Japan
Jun. 2009 by Shimano Inc. PIT. SZK. Printed in Japan
C
Please note: Specifications are subject to change for improvement without notice. (English)
Mount the chain onto the chainring and the sprocket, and then adjust the length of the
chain by adding two links, or four links at a maximum.
Mount the chain onto the sprocket, and then set the hub axle into the dropouts.
Installation to the frame
1.
Place the CT-S510 bracket onto the right side of the hub axle, and place the non-
turn washer onto the left side of the hub axle. At this time, turn the cassette joint so
that the projecting parts of the bracket and non-turn washer fit into the grooves of
the dropouts. If this is done, the cassette joint can be installed so that it is almost
parallel to the chainstay.
(Loosen the arm fixing bolt at this time so that the pulley does not interfere with
other parts such as the frame.)
2.
Loosen the chain line adjustment screw.
Adjustment of the chain line
1.
Mount the chain onto the pulley, and then turn the arm upward so that there is 15 –
25 mm of slackness in the chain when tension is being vertically applied to the chain.
(If tension cannot be applied to the chain
in the upward direction, apply the
tension in the downward direction
instead. If tension cannot be applied in
either the upward or downward direction,
add two links to the chain and apply the
tension in the downward direction.)
Adjustment of the chain tension
1.
Move the pulley sideways until the sprocket and pulley
are in a straight line.
2.
Tighten the chain line adjustment screw to secure the
pulley.
3.
Tighten the arm fixing bolt to secure the
arm.
2.
Turn the crank arm and check that the
wheel turns smoothly with no abnormal
noise.
3.
Place the accessory 2 mm spacer onto the right side (outside of the chain
tensioner), and then secure the wheel to the frame with the cap nuts.
(Recommended tightening torque: 30 – 45 N·m {300 – 450 kgf·cm})
3.
Adjust so that there is 15 – 25 mm
of slackness in the chain when a
force of about 100 g is applied.
SI-50F0A-002
7.1 mm
Applicable hubs
Applicable sprockets
Applicable dropout width
Applicable dropout shape
Internal 7-speed / 8-speed
16T – 23T
4 – 9 mm
Vertical
Non-turn washer
(8L)
Cassette joint
Groove of dropout
CT-S510 bracket
Spacer
(right side
only)
Arm fixing bolt
Chainstay
Chain line adjustment screw
Sprocket
Pulley
Arm fixing bolt
Tightening torque:
12 – 14 N·m
{120 – 140 }kgf·cm
Tightening torque:
1 – 2 N·m
{10 – 20 }kgf·cm
Adjust so that there is 15 – 25 mm
of slackness in the chain when a
force of about 100 g is applied.
* Service Instructions in further languages are available at:
http://techdocs.shimano.com
CT-S510 Chain Tensioner
SI-50F0A-002-00
Product specificaties
| Merk: | Shimano |
| Categorie: | Fietsaccessoire |
| Model: | CT-S510 |
Heb je hulp nodig?
Als je hulp nodig hebt met Shimano CT-S510 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Fietsaccessoire Shimano
12 Juni 2023
9 Juni 2023
8 Juni 2023
6 Juni 2023
4 Juni 2023
23 Mei 2023
22 Mei 2023
21 Mei 2023
20 Mei 2023
20 Mei 2023
Handleiding Fietsaccessoire
- Fietsaccessoire Garmin
- Fietsaccessoire Abus
- Fietsaccessoire Axa
- Fietsaccessoire Bobike
- Fietsaccessoire Bontrager
- Fietsaccessoire Dnt
- Fietsaccessoire Eufab
- Fietsaccessoire Fiamma
- Fietsaccessoire Hema
- Fietsaccessoire Knog
- Fietsaccessoire Master Lock
- Fietsaccessoire Nedis
- Fietsaccessoire Powerfix
- Fietsaccessoire Prophete
- Fietsaccessoire SECURITY Plus
- Fietsaccessoire Silverline
- Fietsaccessoire Stanley
- Fietsaccessoire Tacx
- Fietsaccessoire Thule
- Fietsaccessoire Trelock
- Fietsaccessoire Crivit
- Fietsaccessoire Kayoba
- Fietsaccessoire Stoy
- Fietsaccessoire Lezyne
- Fietsaccessoire Topeak
- Fietsaccessoire Vaude
- Fietsaccessoire Spokey
- Fietsaccessoire Evoc
- Fietsaccessoire Polisport
- Fietsaccessoire Ergon
- Fietsaccessoire SKS
- Fietsaccessoire SBS
- Fietsaccessoire Basil
- Fietsaccessoire Valk
- Fietsaccessoire MET Helmets
- Fietsaccessoire IXS
- Fietsaccessoire Park Tool
- Fietsaccessoire MOTO
- Fietsaccessoire Kemo
- Fietsaccessoire KLICKfix
- Fietsaccessoire AARON
- Fietsaccessoire Pletscher
Nieuwste handleidingen voor Fietsaccessoire
5 Maart 2024
5 Maart 2024
5 Maart 2024
5 Maart 2024
27 Februari 2024
6 December 2023
6 December 2023
16 November 2023
13 September 2023
12 September 2023