SE Electronics X1 S Handleiding

SE Electronics Microfoon X1 S

Lees hieronder de 📖 handleiding in het Nederlandse voor SE Electronics X1 S (23 pagina's) in de categorie Microfoon. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/23

X1 S

U s e r M a n u a l

User Manual - EN

Thank you

We would like to thank you cordially for choosing this sE microphone! This manual contains some

important instructions for setting up and operating your new equipment. Please take a few

minutes to read the instructions below carefully. We hope you will enjoy working with it as much

as we enjoyed designing and building it for you.

Most Sincerely,

Your sE Team

Brief Description

The X1 S is a high-quality condenser microphone intended for a wide range of studio applications,

from vocals to drums to acoustic instruments and beyond. Thanks to its custom design and hand-

crafted 1” true condenser capsule, it delivers pristine sound quality and an even, well-balanced

frequency response.

The electronics and the switchable attenuation pads ensure a high dynamic range, with high

sound pressure level (SPL) handling capability and extremely low-noise components. The

switchable low cut filters eliminate rumble or footfall noise, and can also compensate for an

excess of bass frequencies caused by the proximity effect. This enables the X1 S to close-mic

many instruments including electric guitar speaker cabinets, brass instruments and drums.

Reliable operation even in demanding on-stage applications in difficult environments is ensured by

the roadworthy all-metal design, robust construction, and high quality manufacturing standards.

What’s in the box

Your packaging should contain the follow items. If anything is missing, please contact your sE

Electronics dealer and let them know.

 X1 S microphone

 microphone stand clip

 thread adapt er

Controls

The X1 S features a switch for the attenuation pads and a switch for the low-cut filters.

Attenuation Switch

The is located on the front-left side of Attenuation Switch

the microphone. When switched on, the incoming signal is

reduced by either 10 or 20 dB for capturing of loud

instruments and/or close-miking without distortion. Using

the switch also helps prevent overloading the input stage of

recording interfaces, mixing desks and microphone

preamps.

Low-Cut Switch

The Low-Cut Switch is located on the front-right side of the

microphone, and inserts a low-cut filter at 80Hz (left

position) or 160Hz (right position). The switch’s center

position removes the filter for a flat frequency response.

Wind noise, plosives, footfall noise or rumble might affect

the recorded signal, so enabling the low-cut filters reduces

such unwanted noise and prevents distortion. Additionally,

the low-cut filters also minimize the proximity effect when

recording sound sources at a very short distance.

Powering

To ensure proper operation, the microphone requires a phantom power source providing 48 Volts

according to IEC 61938.

Risk of damage

Do not connect the microphone to any power supply other than a

phantom power source (input with phantom power or external IEC

standard phantom power supply) with a floating connector, using a

balanced cable with studio grade connectors to IEC 268-12 only. This

is the only way to ensure safe and reliable operation.

Safety and maintenance

Risk of damage

Please make sure that the piece of equipment to which your

microphone will be connected fulfils the safety regulations enforced in

your country and is fitted with a ground lead.

Cleaning the microphone

After every use, clean the microphone with a dry, soft cloth tissue and store it in a solid case or a

zipper pouch.

Technical Specifications

Capsule

Hand-crafted 1“ true condenser capsule

Polar patterns

Cardioid

Frequency range

20 20,000 Hz –

Sensitivity

30 mV/Pa (-30.5 dBV)

Max. SPL (0.5% THD)

140 / 150 / 160dBSPL(0/10/20 dB Attenuation pad)

Equivalent noise level

9 dB(A)

Dynamic range

131 / 141 / 151 dB (0/10/20 dB Attenuation pad)

Product specificaties

Merk:	SE Electronics
Categorie:	Microfoon
Model:	X1 S
Kleur van het product:	Zwart
Hoogte:	169 mm
Soort:	Microfoon voor studio's
Connectiviteitstechnologie:	Bedraad
Diameter:	58 mm
Certificering:	IEC 61938
Aansluiting:	XLR-3
Stroomverbruik:	6 mA
Microphone direction type:	Cardioïde
Gevoeligheid microfoon:	-30.5 dB
Operating voltage:	48 V
Spreekspoel types:	Condensor
Frequentie microfoon:	20 - 20000 Hz
Microphone input impedance:	125 Ohm
Aantal producten inbegrepen:	1 stuk(s)
Gewicht microfoon:	445 g
Microfoon Signal-to-Noise Ratio (SNR):	85 dB
Gevoeligheid (1 kHz):	30 mV/Pa
Aanbevolen belastingsimpedantie:	1000 Ohm
Microphone dynamic range:	151 dB
Dempkussen:	20 dB
Equivalent geluidsniveau:	9 dB
laag-af filter:	160 Hz