Sani-Lav ESB2-525L Handleiding

Sani-Lav Spoelbak ESB2-525L

Lees hieronder de 📖 handleiding in het Nederlandse voor Sani-Lav ESB2-525L (3 pagina's) in de categorie Spoelbak. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3

A C O R B AT T E R Y P O WERE D

S I N K S W I T H E L E C T R O NI C S EN S O R S

Operating Manual for Hands-Free Wall Mounted Sinks

AC Models and ES2-525L ES2-525L-0.5

Battery Models and ESB2-525L ESB2-525L-0.5

Columbia does not recommend use with harsh chemicals.

NSF/ANSI Standard 2 - Food Equipment and NSF/ANSI 372 low-lead.

COLUMBIA SPECIFICATIONS

1622 Browning Irvine, CA 92606-4809 Phone: 949.474.0777 Toll Free: 800.626.2117 Fax: 949.474.1191 email: info@ www.columbiasinks.com columbiasinks.com

A C O R B AT T E R Y P O W E R E D

S I N K S W I T H E L E C T R O NI C S EN S O R S

Tools Required

Tape Measure

Adjustable Wrench

Drill Motor and Drill Bits

Pipe Wrench

Level

Safety Glasses

Screw Drivers: 1 Phillips & 1 Standard

Pencil

Socket Wrench

Parts List

(1) Wall mount sink

(1) AC or Battery powered sensor faucet assembly

(1) Wall-mounting bracket

(2) Support brackets

(1) Mixing check valve

(1) Strainer assembly with basket

Installation Instructions

Step 1

1. Establish sink location on the wall.

2. Determine desired height for the top of the backsplash from finished floor and draw a level

line which will be the top edge of the wall mounting bracket.

3. Hold the wall mounting bracket against the wall and mark the wall where the holes are. Drill

holes and secure bracket to the wall as shown in illustration A. Screws are not provided.

4. Position the sink onto wall bracket.

5. Mark holes for fastening side mounting brackets as shown in illustration B.

6. Remove sink from the wall bracket.

7. Drill holes in wall for securing sink to wall. Screws are not provided.

Step 2

1. Install strainer assembly.

2. Install faucets to the sink following the instructions provided with sensor unit.

3. Attach supply tube with elbow to back of faucet.

4. Install mixing check valve and compression fitting to control box of each sensor faucet.

Step 3

1. Position the sink onto wall bracket and secure to wall.

2. Connect waste line to strainer assembly.

3. Mount sensor control box at desired location on wall.

4. Connect power line from sensor to control box.

5. Attach supply tube from faucet to control box.

6. Connect hot and cold water from the source to mixing check valve.

7. Remove aerator from the spout assemblies and flush water system. (see step 7 sensor

installation instructions)

8. Check connections for leaks.

9. Replace aerator onto the spout.

10. We recommend sealing top of backsplash to wall as shown in illustration C.

WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),

Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects

or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

NOTE: Lead content originates from Brass components in valves and faucets and is certied under

NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.

Notice for California Consumers

Illustration A

Illustration B

Illustration C

COLUMBIA SPECIFICATIONS

1622 Browning Irvine, CA 92606-4809 Phone: 949.474.0777 Toll Free: 800.626.2117 Fax: 949.474.1191 email: info@ www.columbiasinks.com columbiasinks.com