Sani-Lav 532A Handleiding
Lees hieronder de π handleiding in het Nederlandse voor Sani-Lav 532A (9 pagina's) in de categorie Spoelbak. Deze handleiding was nuttig voor 4 personen en werd door 2.5 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/9
1
A C O R B AT T E R Y P O W E R E D
S C R U B S I N K W I T H E L E C T R O N I C S E N S O R
Operating Manual for Hands-Free Wall Mount Stainless Steel Scrub Sink
AC Models and 532A 532A-0.5
Battery Models 532B and 532B-0.5
of Domestic and Foreign Parts
Columbia does not recommend use with harsh chemicals.
Product Compliance
NSF/ANSI 2 Food Equipment, NSF/ANSI 372 Lead-Free Compliant, ASME A112.18.1
2
A C O R B AT T E R Y P O W E R E D
S C R U B S I N K W I T H E L E C T R O N I C S E N S O R
COLUMBIA SPECIFICATIONS
800.626.2117 columbiasinks.com info@columbiasinks.com
Β©2021 Columbia Products
Parts List
(1) Wall mount sink
(1) AC or Battery powered sensor faucet assembly
(1) Wall-mounting bracket
(2) Support brackets
(4) Support bracket mounting bolts and washers
(1) Mixing check valve
(1) Strainer assembly with basket
Installation Instructions
Step 1
1. Establish sink location on the wall.
2. Determine desired height for the top of the backsplash from finished floor and draw a level
line which will be the top edge of the wall mounting bracket.
3. Hold the wall mounting bracket against the wall and mark the wall where the holes are. Drill
holes and secure bracket to the wall as shown in illustration A. Screws are not provided.
Step 2
1. Install strainer assembly.
2. Install faucets to the sink following the instructions provided with sensor unit.
3. Attach supply tube with elbow to back of faucet.
4. Install mixing check valve and compression fitting to control box of each sensor faucet.
Step 3
1. Position the sink onto wall bracket.
2. Loosely attach support brackets under sink and push against wall then mark holes for
drilling as shown in illustration B.
3. Remove support brackets from sink and drill holes for mounting fasteners (not provided).
4. Re-mount support brackets to sink and fasten to wall.
Step 4
1. Connect waste line to strainer assembly (s).
2. Mount sensor control box at desired location on wall.
3. Connect power line from sensor to control box.
4. Attach supply tube from faucet to control box.
5. Connect hot and cold water from the source to mixing check valve (s).
6. Remove aerator from the spout assemblies and flush water system. (see step 7 sensor
installation instructions)
7. Check connections for leaks.
8. Replace aerator onto the spout (s).
9. We recommend sealing top of backsplash to wall as shown in illustration C.
Tools Required
Tape measure
Adjustable wrench
Drill motor and drill bits
Pipe wrench
Level
Safety glasses
Screw drivers: phillips and standard
Pencil
Socket wrench
WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),
Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects
or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
NOTE: Lead content originates from Brass components in valves and faucets and is certiξed under
NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.
Notice for California Consumers
Go to for more information on replacement parts and installation videos.columbiasinks.com
Illustration A
Illustration B
Illustration C
3
A C O R B AT T E R Y P O W E R E D
S C R U B S I N K W I T H E L E C T R O N I C S E N S O R
COLUMBIA SPECIFICATIONS
800.626.2117 columbiasinks.com info@columbiasinks.com
Β©2021 Columbia Products
24.75β(628.65mm)
.5β R
(12.7mm)
Hole Conο¬guration
Front
15.5β
(393.7mm)
1.5β (38mm)
19.5β (495.3mm)
2β (51mm)
45ΒΊ
35β (889mm)
suggested
ο¬oor to rim
height
Side
4β (101.6mm)
4β (101.6mm)
16.75β
(425.45 mm)
12.25β
(311.15mm)
4.5β (114.3mm)
Wall-mounting bracket
16β
(406.4mm)
19.5β
(495.3mm)
Top
31β(787.4mm)
15.5β
(393.7mm)
10.25β
(260.35mm)
Cross-breaks
to aid drainage
3.5β drain hole
(88.9mm)
28β (711.2mm)
1.5β (38mm)1.5β
(38mm)
8β
(228.6mm)
10.5β
(266.7mm)
8β
(228.6mm)
10.5β
(266.7mm)
.437β (6mm)
.75β (19mm) slot
.437β (6mm)
dia. hole
.875β (22mm)
dia. holes (1)
2β
(51mm)
.875β
(22.22mm)
Back
Splash
.375β
dia. hole
Wall Mounting Detail
7.5β (191mm)
Product specificaties
| Merk: | Sani-Lav |
| Categorie: | Spoelbak |
| Model: | 532A |
Heb je hulp nodig?
Als je hulp nodig hebt met Sani-Lav 532A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Spoelbak Sani-Lav
12 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
Handleiding Spoelbak
- Spoelbak Seima
- Spoelbak Laveo
- Spoelbak Saro
- Spoelbak Roca
- Spoelbak Kuchinox
- Spoelbak Schock
- Spoelbak Gustavsberg
- Spoelbak Shaws
- Spoelbak Nodor
- Spoelbak Franke
- Spoelbak Krowne
- Spoelbak Blanco
- Spoelbak IKEA
- Spoelbak Fulgor Milano
- Spoelbak Physa
Nieuwste handleidingen voor Spoelbak
11 Juni 2025
11 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
10 Juni 2025
9 Juni 2025
8 Juni 2025