Sani-Lav 512FFL Handleiding

Sani-Lav Spoelbak 512FFL

Lees hieronder de 📖 handleiding in het Nederlandse voor Sani-Lav 512FFL (6 pagina's) in de categorie Spoelbak. Deze handleiding was nuttig voor 14 personen en werd door 7.5 gebruikers gemiddeld met 4.4 sterren beoordeeld

Download PDF

Pagina 1/6

F L O O R M O U N T W A S H S TAT I O N

Operating Manual for -Person Floor Mount Stainless Steel Wash Station 6

Models 512FFL 512FFL-0.5 and

of Domestic and Foreign Parts

Columbia does not recommend use with harsh chemicals.

Product Compliance

NSF/ANSI 2 Food Equipment, NSF/ANSI 61, Section 9, ASME A112.18.1/CSA B125.1

C O L U M B I A S P E C I F I C AT I O N S

F L O O R M O U N T W A S H S TAT I O N

800.626.2117 columbiasinks.com info@columbiasinks.com

Installation Instructions

Step 1

1. Assemble legs for the 54 and 56 series. For series 58, 510 and 512 the legs are pre-assembled.

2. Place wash station sink on the leg assembly. Secure legs to bowl with hardware provided.

3. Place wash station sink at the desired location.

4. Mark the floor where the mounting holes are at the base of the legs. See illustration A.

5. Drill holes as required for mounting hardware. Hardware not included.

Step 2

1. Install Faucet to the sink using faucet mounting kit provided. We recommend using pipe thread

sealant instead of Teflon tape.

2. Install strainer assembly to the drain hole.

3. Connect hot and cold water supply lines (not included) to the back of faucets.

Step 3

1. Position wash station sinks to pre-drilled holes and secure sink to the floor.

2. Connect waste line or drain pipe to the strainer assembly. Not included.

3. Connect water supply lines (Hot and Cold) to the water source. Not included.

4. Remove aerator from the spout and flush the water system.

5. Replace aerator to the spout.

6. Check for leaks and tighten connections if necessary.

Step 4

1. Seal gap between bowl and leg assembly as shown in illustration B.

2. When mounting against wall, it is recommended sealing the top of the backsplash to wall as

shown on illustration C.

Parts List

(1) Floor mount wash station

(1) Leg assembly set

(18) Nuts, bolts and washers for leg assembly

(8) Washers and nuts for connection sink to leg assembly set

(6) 8” on center faucet

(6) Faucet mounting kit

(3) Strainer assembly with basket

Trouble Shooting Guide

Problem Possible Cause To Diagnose Remedy

Water drips

from the spout

or from under

the lever.

1. Seat washer is worn

2. Seat is worn

3. O-rings are worn

Shut cold water source

off. See if water still leaks

from the spout. If leaks

continues repair hot side

if not repair cold side.

Recommend

installing hot

or cold faucet

repair kit.

Go to for more information on replacement parts and installation videos.columbiasinks.com

WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),

Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects

or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

NOTE: Lead content originates from Brass components in valves and faucets and is certied under

NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.

Notice for California Consumers

Tools Required

Tape measure

Adjustable wrench

Drill motor and drill bits

Pipe wrench

Level

Safety glasses

Screw drivers: phillips and standard

Pencil

Socket wrench

Illustration A

Illustration B

Illustration C

C O L U M B I A S P E C I F I C AT I O N S

F L O O R M O U N T W A S H S TAT I O N

800.626.2117 columbiasinks.com info@columbiasinks.com

10”

(254mm)

8” (203mm)

.5” R

(12.7mm)

27” (686mm)

38” (965mm) 38” (965mm) 38” (965mm)

20” (508mm)

7.5” (191mm)

45º

Side

Front

7”

(178mm)

8”

(203mm)

8”

(203mm)

14”

(355.6mm)

14”

(355.6mm)

10”

(254mm)

10”

(254mm)

10”

(254mm)

8”

(203mm)

8”

(203mm)

8”

(203mm)

8”

(203mm)

7”

(178mm)

Hole Conﬁgurations

120” (3048mm)

20” (508mm)20” (508mm) 40” (1016mm) 40” (1016mm)

117” (2972mm)

20”

(508mm)

16.5”

(407mm)

.5” R

(12.7mm)

1.5” (38mm)

2” (51mm)

1.5” (38mm)

Top

6”(152.4mm)

.875” (22mm)

dia. holes (12)

1.5” (38mm)

35” (889mm)

ﬂoor to rim

height

10.25”

(267 mm)

2” drain hole

mounting holes

9” (228.6mm)

on center

9”

(228.6mm)

.75”

(20mm)

2.875”

(73.02mm)

Floor Mounting Detail

.5” dia. Floor

Mounting Holes

9” on Center

1.5” Leg

Thickness

.75” From

Edge of Leg

to First Hole

Supply Line Detail

Back Splash

1/2” Male NPT

Hot

from Wall

Cold

from Wall

Product specificaties

Merk:	Sani-Lav
Categorie:	Spoelbak
Model:	512FFL

Heb je hulp nodig?

Als je hulp nodig hebt met Sani-Lav 512FFL stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Spoelbak Sani-Lav

Sani-Lav 510FA Handleiding

12 Juni 2025

Sani-Lav 54FBL Handleiding

11 Juni 2025

Sani-Lav 56FK1 Handleiding

11 Juni 2025

Sani-Lav 54F1 Handleiding

11 Juni 2025

Sani-Lav 56FBL Handleiding

11 Juni 2025

Sani-Lav 56F8 Handleiding

11 Juni 2025

Sani-Lav 532A Handleiding

11 Juni 2025

Sani-Lav 510F1 Handleiding

11 Juni 2025

Sani-Lav 5030 Handleiding

11 Juni 2025

Sani-Lav 512FFL Handleiding

11 Juni 2025

Handleiding Spoelbak

Nieuwste handleidingen voor Spoelbak

Sloan SS-3036 Handleiding

11 Juni 2025

Sloan SS-3026 Handleiding

11 Juni 2025

Krowne MS-1818 Handleiding

10 Juni 2025

Sloan SS-3017 Handleiding

10 Juni 2025

Stern-Williams SS-2424 Handleiding

10 Juni 2025

Sloan SS-3117 Handleiding

10 Juni 2025

Sloan SS-3055 Handleiding

10 Juni 2025

Advance Tabco 9-OP-36FM Handleiding

10 Juni 2025

Kernau KGS M 6078 1B1D Handleiding

9 Juni 2025

Kernau KGS B 90 1B1D Handleiding

8 Juni 2025