Roland MDS-Standard 2 Handleiding

Bekijk gratis de handleiding van Roland MDS-Standard 2 (1 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 56 mensen en kreeg gemiddeld 4.9 sterren uit 5 reviews. Heb je een vraag over Roland MDS-Standard 2 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

NOTE

•Whensetting-uporadjustingthestand,takecarenottopinchyourngersbetweenmovablepartsandthemainunit.Ifusingthisinalocationwherechildrenarepresent,besuretoprovideadultsupervisionorguidance.

•Prepareanareainwhichyoucanperformtheassemblysafely.

•Donotuseapowertool(e.g.,anelectricscrewdriver)toassemblethestand.Youriskdamagingorstrippingthescrews.

•Whenremovingthepartsfromthepackingcarton,takecarethatyourboxcutterorothersharpimplementdoesnotscratchthepipes.

•Ifyouwillbeusingthisdrumstandforanextendedperiodoftimeinthesamelocation,werecommendthatyouuseadrummat(TDMseries)madebyRolandtopreventtherubberfeetfromsoilingthesurfaceonwhichtheyareplaced.

Beforeusingthisunit,carefullyread“USINGTHEUNITSAFELY”and“IMPORTANTNOTES.”Afterreading,keepthedocument(s)

whereitwillbeavailableforimmediatereference.

Roland,V-DrumsareeitherregisteredtrademarksortrademarksofRolandCorporationintheUnitedStatesand/orothercountries.

Owner’s Manual

©2019RolandCorporation

How to Set Up the Stand

1.

Check the parts

Beforeyoustartassemblingthestand,makesurethat

youhavealloftheparts.

1

2

3

4

56

7

8

10

9

11

12

13

NumberNameQuantity

1StraightpipeL(Long)1

2

CurvedpipeL

(withonepadmount,withonememorylock)

1

3Centerpipe(upper)(withtwopadmounts)1

4Centerpipe(lower)1

5MainunitpipeL(secondholderhigher)1

6MainunitpipeR(secondholderlower)1

7

CurvedpipeR

(withtwopadmounts,withonememorylock)

1

8StraightpipeR(Short)1

9Cymbalmount3

10Padmount3

11Cableclip4

12Drumkey1

13Cabletie4

2.

Assembling the center section

2–1. Attachthecenterpipes(upper

3

/lower

4

)tothe

mainunitpipeL

5

.

•Insertthecenterpipe(upper)

3

intothetop

holderofthemainunitpipeL

5

.

•Insertthecenterpipe(lower)

4

intothethird

holderfromthetop.

Center pipe (upper)

3

Main unit pipe L

5

Center pipe (lower)

4

Aligntheguideholewiththegapoftheholder,

andtighten(twolocations)usingthedrumkey

12

.

2–2. AttachthemainpipeR

6

.

•Insertthecenterpipe(upper)

3

intothetop

holderofthemainunitpipeR

6

.

•Insertthecenterpipe(lower)

4

intothe

secondholder.

Center pipe (upper)

3

Main unit pipe R

6

Center pipe (lower)

4

Aligntheguideholewiththegapoftheholder,

andtighten(twolocations)usingthedrumkey

12

.

3.

Attaching the left arm section

3–1. Positionthesecondholderfromthetopofthemain

unitpipeL

5

facingoutward,andinsertthecurved

pipeL

2

.

Curved pipe L

2

Main unit pipe L

5

Aligntheguideholewiththegapoftheholder,

andtightenusingthedrumkey

12

.

3–2. Alignthememorylockwiththeholder,andtighten

usingthedrumkey

12

.

Alignpositions

Memory lock

3–3. AttachthestraightpipeL

1

.

Aligntheguideholewiththegapoftheholder,

andtightenusingthedrumkey

12

.

Straight pipe L

1

4.

Attaching the right arm section

4–1. PositionthebottomholderofthemainunitpipeR

6



facingoutward,andinsertcurvedpipeR

7

.

Curved pipe R

7

Main unit pipe R

6

Aligntheguideholewiththegapoftheholder,

andtightenusingthedrumkey

12

.

4–2. Alignthememorylockwiththeholder,andtighten

usingthedrumkey

12

.

4–3. AttachthestraightpipeR

8

.

Aligntheguideholewiththegapoftheholder,

andtightenusingthedrumkey

12

.

Straight pipe R

8

4–4. Verifythatthefourverticalpipesaretrulyvertical.

Ifthestandwobbleswhenplacedontheoor,

loosentheholdersandmakeadjustments.

5.

Assembling the cymbal mount

5–1. Loosenthehandknobandpullouttherod.

Hand knob

Joint

Rod

5–2. Rotatethejointandinserttherod.

Joint

5–3. Tightenthehandknob.

6.

Attaching the pad mounts and cymbal mounts

Pad mounts

10

Cymbal mounts

9

6–1. Raisethemountholders(threelocations)ofthe

centerpipe(upper)

3

andthecurvepipeR

7

.

Mount holders

6–2. Attachpadmounts

10

totheholdersthatyouraised,

andtightenusingthehandknobs(threelocations).

Hand knobs

6–3. Attachthecymbalmounts

9

inthepositionsshown

intheillustration,andtightenusingthehandknobs

(threelocations).

Notes

•Whensettinguporstoringthestand,becarefulnot

topinchthengersyouusetohandlethestand.

•Regardingthewayofmountingadrumsound

module,pads,orcymbals,pleaserefertothesetup

guideofyourdrumkit.

Aligning the position of pipes and holders

Align the guide hole with the gap of the holder

Rotatetheinserted

pipe,adjustingitso

thattheguideholeis

visiblethroughthegap

oftheholder.

Guide hole

Gap

Rotate pipe to adjust

Usethecableclips

11

andcableties

13

tomanagethecables

neatlywhenattachingthepadsandthesoundmodule.

Whensettingup,payattentiontosafetysothatthestanddoesnotfallover.

Refertothesetupguideofyourdrumkit,andobservethesafetyprecautionswhensettingup.

Assembly for a Left-Handed Player

Forleft-handeduse,assemblethestandwithleftandrightreversedasshownintheillustration.

•Beforeyoubeginwork,loosenthememorylocksofcurvedpipesL

2

andR

7

.Whenyounishassembly,

adjustthepositionandretighten.

•Forthepositionatwhichtoattacheachmount,refertothesetupguideofyourdrumkit.

Straight pipe L

1

Center pipe (upper)

3

Center pipe (lower)

4

Main unit pipe L

5

Straight pipe R

8

Pad mount

10

Main unit pipe R

6

Cymbal mount

9

Memory lock

Curved pipe L

2

Curved pipe R

7

Aligning the position of pipes and holders

1. Turn the inserted pipe to align the guide hole with

the holder notch (the mark at which to align the

memory lock), and push it all the way in.

Holdernotch

Guidehole

Adjusting the memory lock

1. Use the drum key

12

to loosen the screw of the

memory lock.

2. Rotate the memory lock 180 degrees, and align

the hock mark.

Alignpositions

Memorylock

3. Use the drum key

12

to securely tighten the

memory lock screw.

2

English

Product specificaties