Roberts SportsDAB 55 Handleiding
Pagina's 2 Radio
Bekijk de handleiding van Roberts SportsDAB 55 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
Important:The batteries should not be exposed to excessive heat such as sunshine, re or the
like. After use, disposable batteries should if possible be taken to a suitable recycling centre. On
no account should batteries be disposed of by incineration. Replace batteries only with Caution:
the same or equivalent type. Danger of explosion if the batteries are incorrectly replaced.
1 Remove the battery cover on the back of the unit by sliding
the cover in the direction of the arrow.
2 Insert 2 x AA / LR6 size batteries into the spaces in the
compartment. Take care to ensure all batteries are inserted
with the correct polarity as shown inside the battery
compartment. Replace the cover.
3 When the batteries are exhausted the radio will go off.
Reduced power, distortion and a ‘stuttering’ sound are all
signs that the batteries may need replacing.
4 If the radio is not used for any extended period of time it is
recommended that the batteries are removed from the radio.
5 Battery replacement does not cause the station list or preset
stations to be lost.
The Keylock functionis used to prevent unintentional
operation of your radio.
1 Set the Lock switch located on the rear of your radio to
the 'Lock'position. The On/Off and all other buttons
will be disabled. This will prevent accidental operation
when your radio is packed in a suitcase or travel bag.
If a button is accidentally pressed then ‘Key Locked’
will show on the display.
2 To release the Lock switch, move the lock switch to
the position.‘Unlock'
12
The lead connecting the headphones to your radio acts
as an aerial when plugged into the Headphone socket.
The lead should be fully extended as much as possible
to increase reception.
1 Plug the headphones into the Headphone socket on
the top of your radio. Check that the Volume levelis
not too loud before placing the ear-pieces into your
ears.
IMPORTANT: Plug the headphones into the radio and switch on the
radio before inserting the headphones into your ears. Excessive sound
pressure from headphones can cause hearing loss. To prevent possible
hearing damage, do not listen at high volume levels for long periods.
Scanning...
Stations: 115
Scan11:43
Key Locked
11:43DAB
Station Order
Slide Show
Sleep
System Settings
Back
Alphan>
Full Scr>
>
>
Signal error: 25
Strength:
DAB
BBC Radio5Live
11:43
11:43DAB
Mode -> FM
Scan
Manual Tune
Prune
DRC
>
>
O>
1 Carefully, fully extend the headphone antenna.
2 Press the On/Off button to switch on your radio. The
display will show ‘ROBERTS SportsDAB 55’.
3 If this is the rst time the radio is used a scan of the
Band III DAB channels will be carried out. If the radio
has been used before the last used station will be
selected.
4 When the scanning is completed the rst station (in
numeric-alpha order 0...9...A....Z) will be selected.
Your radio will automatically set to the current time.
If the station list is still empty after the scan your radio
will display ‘No stations found’.
5 If no signals are found it may be necessary to relocate
your radio to a position giving better reception. Then,
either switch your radio off and on again, or repeat
the scan.
1 When in DAB mode, push the either up or Jog wheel
down to scroll through the list of available stations.
2 Press the to select the station. Adjust the Jog wheel
Volume to the required setting.
• If you are currently in FM mode, press and hold the
Jog wheelto enter the menu and then press the Jog
wheel again to switch modes from FM to DAB.
• Press the to cycle through the various Jog wheel
options. The display options are scrolling text, program
type, multiplex name, channel/frequency, signal
strength (the minimum signal marker () shows the
minimum strength needed for good DAB reception),
bit rate and date.
Some radio stations may have one or more additional
broadcasts associated with them. If these are available
they will appear immediately after the main station.
As time passes new stations may become available. To
nd new stations proceed as follows:-
1 Ensure your radio is in DAB mode. Press and holdthe
Jog wheel.
2 Push the Jog wheel down until is highlighted ‘Scan’
on the display and press the to select.Jog wheel
3 The display will show ‘Scanning...’ and your radio
will perform a scan of the Band III DAB channels. As
new radio stations are found the station counter on
the right-hand side of the display will increase and
the radio stations will be added to the list stored in
the radio.
1 Press and holdin the to access the main Jog wheel
menus.
2 Many operations require the user to make a selection
from the menus. Push the Jog wheel up or down to
highlight the desired menu item and then press the
Jog wheel to select that item. Arrows are used to show
that there are more items in that menu.
3 If an error is made or you wish to go to the previous
screen there is a menu item in most menus. Push ‘Back’
the Jog wheel Up or Down until is highlighted ‘Back’
and press the Jog wheel to select it. After a period
of inactivity the display will revert to the previous
information display.
continued overleaf...
STEP 1 - Before first useSTEP 2 - Operating your radio DAB
What is in the Box?
Personal radio | stereo headphones | quick start guide | safety/warranty leaet
• DAB+ / FM wavebands
• 10 direct access presets (5 DAB and 5 FM)
• Automatic time set
• Colour LCD display
• Keylock
• Stereo headphones
• 2x AA / LR6 batteries (not included)
12
3
4
5
6
7
8
9
10
11
The day’s main
news stories,
topical debate
and interviews.
DAB
BBC Radio5Live
11:43
154
A
F
G
E
I
H
J
B
C
D
Controls
Display Icons
Features
Battery Operation
Lock Switch
Navigation
Selecting a Station
Finding New Radio Stations
Headphones
Operation
12
Headphone socket1
Presets 1 - 52
On/Off button3
Headphones4
Colour LCD Display5
6 Jog wheel (Tuning/Select/
Menu/Back)
A DAB/FM mode
Radio station/FrequencyB
DAB/FM symbolC
D Sleep timer
Battery indicatorE
F Time (24 hour format)
G Information
H Stereo indicator
I Signal strength indicator
Preset indicatorJ
7 USB socket for service use only (inside
battery compartment)
Battery Compartment8
9 Volume Up button
10 Volume Down button
11 Keylock Switch
12 QR code for online instructions
Manual tuning allows you to tune directly to the various DAB Band III channels.
1 Press and hold the . Push the Jog wheelJog wheel up or down until ‘Manual Tune’ is
highlighted on the display.
2 Press the Jog wheelto select ‘Manual Tune’ and then push the up or down Jog wheel
to highlight the desired channel.
3 Press the Jog wheel. The graph will indicate the signal strength and the upper line
will show the name of the DAB multiplex (group of stations). Any stations found will
be added to the stored list in the radio. Press the to return to the list of DAB Jog wheel
channels.
4 Press and hold the to return to the menu.Jog wheel
Dynamic Range Control (also known as DRC) can make quieter sounds easier to hear
when your radio is used in a noisy environment.
1 Press and holdthe . Push the Jog wheelJog wheelup or down until is highlighted ‘DRC’
on the display. Press the Jog wheel to enter the DRC settings menu.
2 Push the Jog wheelup or down to select the required DRC setting, ‘’, ‘’ or ‘OffLowHigh’
(the default is off). The current DRC setting will be marked with a tick.
3 Press the Jog wheel. The display will return to the previous display. Not all DAB Note:
broadcasts are able to use the DRC function. If the broadcast does not support DRC,
then the DRC setting in the radio will have no effect.
1 Push the Jog wheel up or down to tune to a station. With each push of the Jog wheel
the frequency will change up or down by 50 kHz. When the waveband end is reached
the radio will recommence tuning from the opposite waveband end.
2 Set the Volume to the desired settings.
• Press the Jog wheel to cycle through the various options. The display options are
scrolling text, program type, audio mode, time and date.
If a station is weak some hiss may be audible.
1 To reduce the hiss, press and hold the Jog
wheel to enter the menu and then push up or
down until is highlighted. Press ‘Audio Setting’
the .Jog wheel
2 Choose ‘Forced Mono’. Your radio will select
the mono audio mode.
3 To return to stereo mode, choose ‘Stereo
Allowed’. Your radio will switch to stereo mode.
1 Press and hold the Jog wheel to enter the menu and then push
up or down until ‘Scan Setting’ is highlighted.
2 Press the Jog wheel.
3 Choose between ‘Strong Stations Only’ (local) and ‘All Stations’
(distant) options. The ‘All Stations’ option will allow the radio to
nd weaker signals when scanning. The local or distant setting
is stored in the radio and remains in force until changed or until
a system reset.
You may store your preferred DAB
and FM radio stations to the preset
station memories. There are 10
memory presets in your radio, 5 for
DAB and 5 for FM.
1 Press and release the button to switch on the radio.On/Off
2 Select the desired waveband and tune to the required station.
3 Press and hold the required Preset button (1-5) until the display
shows, for example, ‘Preset 1 saved’. The station will be stored
under the chosen preset button.
4 Repeat this procedure for the remaining presets. Stations stored
in preset memories may be overwritten by following the above
procedure.
1 To recall preset stations, press and release the On/Off button to
switch on the radio and then select the desired waveband.
2 Press and release the required Preset button. Your radio will tune
to the chosen preset station stored in the preset memory. The
display will show, ‘Preset Empty’ if no station has been stored to
that preset.
Your radio can be set to turn off after a preset time has elapsed.
1 Enter the menu and then choose ‘Sleep’.
2 Choose the desired sleep time between 15 and 120 minutes or
‘Off’ which will cancel the sleep function.
3 The sleep timer indicator
S
will show on the display. Your radio
will switch off after the preset sleep time has elapsed.
4 To cancel the sleep timer and switch off your radio before the
chosen sleep time has elapsed, press the On/Off button or set
the sleep timer to Off.
The display backlight has two settings that can be accessed from the
‘System Settings’ menu. The backlight can either be left on whilst the
radio is in use or can be set to automatically dim to low brightness after
10 seconds of inactivity. This will improve battery life.
1 To set the backlight to automatically dim after 10 seconds of
inactivity, press and holdthe Jog wheel and choose ‘System Settings’
and then choose ‘Backlight Settings’.
2 Choose ‘Backlight Auto’and select ‘Yes’, so that the backlight
will dim after 10 seconds of inactivity. The radio will return to the
previous menu.
3 If you require the backlight to be on continuously choose .‘No’
The display brightness can also be set in the ‘’ menu. Backlight Settings
1 Within the ‘Backlight Settings’ menu, choose ‘’.Brightness
2 Select either ‘’, ‘’ or ‘HighMediumLow’. The radio will return to the
previous menu.
If your radio fails to operate correctly,
1 Press and holdthe Jog wheel. Choose ‘System Settings’, ‘Factory
Reset’ and then ‘Yes’. A full reset of your radio will be performed.
All presets and station lists will be erased.
1 Press and hold the Jog wheel. Choose ‘System Settings’,
‘Language’ and then the desired language.
The software cannot be altered and is just for your reference.
1 To view the software version the press and holdJog wheel.
Choose ‘System Settings’ and then ‘Software Version’.
11D 222.064MHz
Strength:
Manual Tune11:43
11:43DRC
High
Low
O
Proceed to prune the
invalid stations?
Prune
Yes
No
11:43
93.20MHz
RDS
FM
BBC R4
11:43
Step 2 - Operating your radio DAB cont.
Step 3 - Operating your radio - FM
Other information
Over time, some DAB services may stop broadcasting, or may change location. This
function will delete the DAB stations from your station list that can no longer be received.
1 Press and holdthe . Push the Jog wheelJog wheelup or down until ‘Prune’is highlighted
on the display. Press the Jog wheel.
2 Push the Jog wheel down to highlight ‘Yes’.
3 Press the Jog wheel to cause the stations list to be pruned, eliminating unavailable
stations.
1 Carefully extend the aerial lead fully. Press the On/Off button to switch on your radio.
2 If you are currently in DAB mode, press and holdthe Jog wheelto enter the menu and
then press the Jog wheel again to switch modes from DAB to FM.
3 Push the Jog wheel up and hold for 2 seconds, your radio will scan in an upwards
direction (low to high frequency) and stop automatically when it nds a station of
sufcient strength.
4 After a few seconds the display will update. The display will show the frequency of
the signal found. If the signal is strong enough and there is RDS data present then
the radio may display the station name.
5 To scan the FM band in a downwards direction (high to low frequency) push the Jog
wheel down and hold for 2 seconds. Adjust the Volume to the required setting.
Batteries 2 x AA size / LR6 (not included)
Battery life 10 - 18 hours depending on operating mode
when using alkaline batteries.
Frequency coverage FM 87.5 - 108MHz, DAB 174.928 -
239.200MHz
Aerial system DAB / FM earphone antenna
Earphone Jack 3.5mm stereo
Please read this guide and the safety/
warranty leaet before use
DAB+/FM Personal Digital Radio
SportsDAB 55
ROBERTS RADIO LIMITED
www.robertsradio.com
© 2026 Roberts Radio Limited
Issue 1
2026-03-31
Designed & Engineered in the UK
Roberts Radio Ltd, Roberts House, Hanworth Lane, Chertsey, KT16 9JX, UK
Glen Dimplex Europe Ltd, Airport Road, Cloghram, Co. Dublin, K67 VE08, Ireland
Manual Tuning - DABPreset StationsSleep Function
Backlight Settings
System Reset
Language
Software Version
Specications
Scan Sensitivity - FM
Manual Tuning - FM
Stereo/Mono - FM
Search Tuning - FM
Dynamic Range Control - DAB
Prune Stations - DAB
Product specificaties
| Merk: | Roberts |
| Categorie: | Radio |
| Model: | SportsDAB 55 |
Heb je hulp nodig?
Als je hulp nodig hebt met Roberts SportsDAB 55 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden