Reflecta 23122 Handleiding

Reflecta Flat panel steun 23122

Lees hieronder de 📖 handleiding in het Nederlandse voor Reflecta 23122 (7 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/7

6. Installing the Display

INSTALLATION MANUAL

LCD Ceiling Mount

23 12 2

42"

MAX

75x75/100x100

200x100/200x200

ISSUED: MAY. 2015

330

00k

kkg

(

((6

666

66l

llb

bbs

ss)

)

))

RRATE

ATE

ATEATED

30kg

(66lbs)

RATED

7. Adjustment

Use the tilt adjusting knob to adjust your display to the desired angle then tighten it.

Maintenance

• Check that the bracket is secure and safe to use at regular intervals(at least every three months).

• Please contact your dealer if you have any questions.

M-A

M-B M-E

180 °

+20 °

-20 °

Tighten all screws but do not over tighten.

Lift the display and match the holes on your display with the holes on the mount. Secure your display to

the mount by tightening screws.

Note: Choose the appropriate screws, washers and spacers (if necessary) according to the type of screen.

M-D

M-F

M-G

M-D

M-F M-G

TVTV

M-C

M-D M-F

or or

CAUTION: DO NOT EXCEE D

RATED LISTED WEIGHT. SERIOUS

INJURY OR PROPERTY DAMAGE

MAY OCCUR!

reflecta gmbh

Merkurstrasse 8

72184 Eutingen i.G.

Germany

mail@reflecta.de

www.reflecta.de

Component Checklist

IMPORTANT: Ensure that you have received all pa rts according to the component checklist prior to installation.

If any parts are miss ing or faulty, telephone y our local distributor for a replacement.

Package M

Package W

concrete anchor (x4)

W-B

ST6.3x55 (x4)

W-A

D8 washer (x4)

M-F

D5 washer (x4)

M-E

small spacer (x8)

M-G

M5x14 (x4)

M-B

M6x14 (x4)

M-C

M8x20 (x4)

M-D

M4x14 (x4)

M-A

plastic cover (x1)

grip holder (x1)

ceiling plate (x1)

plastic bushing (x2)

outer column (x1)

Inner column (x1)

M8 washer (x2)

M6x45(x3)

M8x45(x1)

M8 (x1)

plastic pad (x1)

M6 nut (x3)

M8 nut (x1)

washer (x1)

M8x20 (x1)

VESA plate

(x1)

D8 washer (x2)

NOTE: Read the entire instruction manual before you start installation and assembly.

WARNING

• Do not begin the installation until you have read and understood all the instructions

and warnings contained in this installation sheet. If you have any questions

regarding any of the instructions or warnings, please contact your local distributor.

• This mounting bracket was designed to be installed and utilised ONLY as

specified in this manual. Improper installation of this product may cause damage

or serious injury.

• This product should only be installed by someone with good mechanical ability

who has basic building experience and fully understands this manual.

• Make sure that the supporting surface will safely support the combined weight of

the equipment and all attached hardware and components.

• If mounting to wooden joist ceiling, make sure that mounting screws are anchored

into the center of the joist. The use of a stud finder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position

the equipment.

• Tighten screws firmly, but do not over tighten. Over tightening can cause damage

to the items, This greatly reduces their holding power.

• This product is intended for indoor use only. Using this product outdoors could

lead to product failure and personal injury.

Product specificaties

Merk:	Reflecta
Categorie:	Flat panel steun
Model:	23122
Kleur van het product:	Zilver
Montagewijze:	Plafond
Maximale gewichtscapaciteit:	30 kg
Paneelmontage-interface:	50 x 50,75 x 75,100 x 100,200 x 100,200 x 200 mm
Draaihoek:	90 °
Montage interface compatibiliteit (min):	50 x 50 mm
Montage interface compatibiliteit (max):	200 x 200 mm
Aantal displays ondersteund:	1
Bereik kantelhoek:	-20 - 20 °
Maximale schermgrootte:	37 "
Minimale schermgrootte:	17 "