RDL TX-TPR2A Handleiding

RDL Niet gecategoriseerd TX-TPR2A

Lees hieronder de 📖 handleiding in het Nederlandse voor RDL TX-TPR2A (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
TWISTED PAIR FORMAT-A
Models D-TPR2A, DB-TPR2A, DS-TPR2A
Format-A Two-Pair Receivers
• Two Unbalanced -10 dBV Phono Jack Audio Outputs
• L (Left) Output From Pair B; R (Right) From Pair C
• Signal and Power Pair Pass-Through on RJ45s
• Remote Powering through Twisted Pair Cable
• Fused Local Power Feeds all Connected Modules
• Local Power Input on Terminal Block
• Blue LED Indicates Module is Powered
• Daisy-Chain with Additional Format-A Receivers
• Studio-Quality Precision Active Balanced Circuitry
The D SERIES-TPR2A modules are two-pair audio receiving modules compatible with RDL Format-A twisted pair products. These modules are designed to be
mounted in wall boxes, cabinets or other enclosures that allow users to connect external equipment. The -TPR2A models mount in RDL WB-1U and WB-2U wall
boxes, or in standard U.S. electrical boxes. The D-TPR2A features a white front-panel laminate with gray lettering that matches RDL Decora©-style remote controls.
The DB-TPR2A features a black front-panel laminate. The DS-TPR2A is c
onstructed of stainless steel to coordinate with RDL Decora-style stainless steel remote
controls in commercial/industrial installations.
APPLICATION: The D SERIES-TPR2A modules feature two RCA phono jack outputs, one for the left channel
output and one for the right channel. The audio signals received from pairs B and C of the twisted pair cable are
buffered to drive the output jacks at the standard -10 dBV consumer level.
This module receives signal from only two cable pairs, so the D SERIES-TPR2A modules have a second RJ45 jack
to connect cables to additional receiver modules. A separate single-pair receiver may be chained to the second
RJ45 jack. In addition to completing the reception of signals from all three FORMAT-A pairs, additional receivers
may be connected to the same twisted pair feed. The bridging input circuits used in all FORMAT-A twisted pair
receivers allow connection of up to 10 receiver outputs for each cable pair. The possibility of multiple receiver
locations adds enormous flexibility in the design of audio routing systems using RDL FORMAT-A products. The
power pair and all three audio pairs are fed through both rear-panel RJ45 jacks.
The D SERIES-TPR2A may be powered directly from a 24 Vdc power supply using the rear-panel detachable
terminal block. Local power connected to the module is also fed to all connected remote modules. The -TPR2A
may be remotely powered through the twisted pair cable from any other module, signal distributor or RDL power
inserter connected to the same twisted pair cable. Module power is indicated by a front-panel LED.
RDL FORMAT-A features superior audio performance that rivals or exceeds shielded wiring. Design simplicity,
ease of installation, unsurpassed flexibility, automatic fused power, exceptional hum rejection, low noise, and low
distortion provide designers and installers the optimum choice in economical twisted pair products.
RDL ï‚·
ï‚·
ï‚·
ï‚·ï‚· 659 6th St. ï‚·
ï‚·
ï‚·
ï‚·ï‚· Prescott, AZ., USA 86301 ï‚·
ï‚·
ï‚·
ï‚·ï‚· ï‚·
ï‚·
ï‚·
ï‚·ï‚· (928) 443-9391 FAX (928) 443-9392 ï‚·
ï‚·
ï‚·
ï‚·ï‚· www.rdlnet.com
D-TPR2A DS-TPR2A DB-TPR2A
TWISTED PAIR FORMAT-A
Models D-TPR2A, DB-TPR2A, DS-TPR2A
Format-A Two-Pair Receivers
TYPICAL PERFORMANCE
Input: RDL FORMAT-A
Input Connection: RJ45
Format-A Signal Pairs Used (2): B (Left); C (Right)
Format-A Output: RJ45
Output: 100 Ω unbalanced
Output Connection: RCA Phono
Frequency Response: 10 Hz to 50 kHz (+/- 0.1 dB)
THD+N: < 0.005%
Noise below +4 dBu: < -90 dB
Crosstalk: < 90 dB (1 kHz); < 75 dB (20 Hz to 20 kHz)
Headroom above +4 dBu: > 18 dB
CMRR: > 80 dB (50 Hz to 150 Hz)
Indicator: Power In
Power Connections (2): Detachable terminal block; RJ45
Power Requirement: 24 Vdc @ 45 mA plus connected loads
Maximum Load Current: 155mA
Dimensions: 1.6" (4.06 cm) W; 4.11" (10.45 cm) H; 1.89" (4.8 cm) D
Mounting Box Minimum Depth: 2.4"
Declaration of Conformity available from rdlnet.com.
Sole EMC specifications provided on product package.
Specifications are subject to change without notice.
Installation/Operation
STEP 1: Connect 24 Vdc to the power input terminals if this module is not being powered through the twisted pair cable from another module, or if
this module is located an excessive distance from the next powered module on the cable. Note: The front-panel power LED will
be illuminated if
this module is powered. If this module is powering other modules through the cable and if there is a wiring short, the short must be cleared then
power must be turned off to this module for 10 seconds to reset the internal protection circuit.
STEP 2: Connect the twisted pair cable coming from Format-A senders or distributors.
STEP 3: Connect the twisted pair cable feeding additional Format-A receiver(s), if any, and fasten the module in its mounting box.
891-4580C
Radio Design Labs Technical Support Centers
U.S.A. (800) 933-1780, (928) 778-3554; Fax: (928) 778-3506
Europe [NH Amsterdam] (++31) 20-6238 983; Fax: (++31) 20-6225-287
(1) + White / Green
(2) – Green
(3) + White / Orange
(4) – Blue
(5) + White / Blue
(6) – Orange
(7) + White / Brown
(8) – Brown
Pair A: Audio +4 dBu
Pair B: Audio +4 dBu
Pair C: Audio +4 dBu
Pair D: Power +24 Vdc
Tab on bottom of connector
RJ45 Standard wirin
g
RJ45 conductor colors shown are for 568A standard. The 568B standard may be used if the connectors at both ends of the cable are wired identically.
TP CABLE
24 VDC
D SERIES-TPR2A
TWISTED
PAIR CABLE TWISTED
PAIR CABLE
REQUIRED CONNECTION OPTIONAL CONNECTION
NOTE: Connect a 24 Vdc power supply
to the module if power is not being
supplied through a twisted pair cable
from a connected module.
24 Vdc power
connection
(see note)
Connection from Single-Pair, Two-Pair
or Three-Pair Senders (direct, or via an
RDL Twisted Pair Power Inserter)
or
Connection from Format-A Distributor
or
Connection from other Format-A
Receivers
Connection to additional Format-A
Receiver(s)
or
Connection to Format-A Receiver(s) via
an RDL Twisted Pair Power Inserter
or
Connection to Format-A Distributor Input

Product specificaties

Merk: RDL
Categorie: Niet gecategoriseerd
Model: TX-TPR2A

Heb je hulp nodig?

Als je hulp nodig hebt met RDL TX-TPR2A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd RDL

RDL

RDL D-BT1A Handleiding

8 Januari 2024
RDL

RDL TX-TPR1A Handleiding

8 Januari 2024
RDL

RDL ST-LCR1 Handleiding

27 Juni 2023
RDL

RDL DDS-RN40 Handleiding

19 April 2023
RDL

RDL DDB-RN31 Handleiding

27 Maart 2023
RDL

RDL DDB-BTN44 Handleiding

4 Maart 2023
RDL

RDL DDB-RN40 Handleiding

30 Januari 2023
RDL

RDL DD-RN40 Handleiding

18 Januari 2023
RDL

RDL TX-TPR2A Handleiding

13 November 2022
RDL

RDL DDS-RN31 Handleiding

8 November 2022

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024
Sony

Sony PDW-U4 Handleiding

26 April 2024
Sony

Sony NXL-FR318 Handleiding

26 April 2024