Rane RPM 26z Handleiding
Rane
Niet gecategoriseerd
RPM 26z
Bekijk gratis de handleiding van Rane RPM 26z (10 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 7 mensen en kreeg gemiddeld 5.0 sterren uit 4 reviews. Heb je een vraag over Rane RPM 26z of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/10
RPM 26z
PROGRAMMABLE MULTIPROCESSOR
INPUT AES3 OUTPUT
1 2 A B 1 432 65LOCK
VIP POWER
ETHERNET STATUS
RPM 26z
PROGRAMMABLE
MULTIPROCESSOR
PRESET
24
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
To reduce the risk of electrical shock, do not open the unit. No user
serviceable parts inside. Refer servicing to qualied service personnel.
e symbols shown below are internationally accepted symbols that warn
of potential hazards with electrical products.
is symbol indicates that a dangerous voltage
constituting a risk of electric shock is present within
this unit.
is symbol indicates that there are important
operating and maintenance instructions in the
literature accompanying this unit.
WARNING
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, registers, stoves, or other apparatus (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A ground-
ing-type plug has two blades and a third grounding prong. e wide blade or third prong is provided for your safety. If the provided plug does not
t into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord and plug from being walked on or pinched particularly at plugs, convenience receptacles, and the point where it exits from
the apparatus.
11. Only use attachments and accessories specied by Rane.
12. Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply
cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
15. e plug on the power cord is the AC mains disconnect device and must remain readily operable. To completely disconnect this apparatus from
the AC mains, disconnect the power supply cord plug from the AC receptacle.
16. is apparatus shall be connected to a mains socket outlet with a protective earthing connection.
17. When permanently connected, an all-pole mains switch with a contact separation of at least 3 mm in each pole shall be incorporated in the electri-
cal installation of the building.
18. If rackmounting, provide adequate ventilation. Equipment may be located above or below this apparatus, but some equipment (like large power
ampliers) may cause an unacceptable amount of hum or may generate too much heat and degrade the performance of this apparatus.
19. is apparatus may be installed in an industry standard equipment rack. Use screws through all mounting holes to provide the best support.
WARNING: To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture. Apparatus shall not be exposed to dripping
or splashing and no objects lled with liquids, such as vases, shall be placed on the apparatus.
NOTE: is equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
ese limits are designed to provide reasonable protection against harmful interference in a residential installation. is equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio commu-
nications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUT ION: Changes or modications not expressly approved by Rane Corporation could void the user's authority to operate the equipment.
is Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Shielded CAT5e or better cables are required in order to comply with the FCC Rules part 15 limits for a Class B digital device.
Manual-1
RPM 26z
PROGRAMMABLE MULTIPROCESSOR
HARDWARE MANUAL
WEAR PARTS: is product contains no wear parts.
QUICK START
is section is intended to help you make the physical connec-
tions and software manipulations necessary to get up and run-
ning with your sleek new RPM 26z. If you don’t read the entire
Hardware Manual, at least read this section. It is also recom-
mended that you read the Quick Start section of the Drag Net
Software Manual. If the Drag Net software is not yet installed
on your computer, please install it now.
To be safe, leave the audio connections until last. Begin by
connecting the IEC power cord. Observe that the LED POWER
on the front panel illuminates. After a few seconds, the STATUS
LED should turn from red to yellow to green, and the PRESET
display should have a number in it (00, if it’s the rst time you’ve
powered the device). If the comes on, but the POWER STATUS
LED does not turn green, contact the factory.
Connect one end of the Ethernet crossover cable (supplied
with the unit) to the jack on the rear panel. Connect 10Base-T
the other end of the cable to an Ethernet port on your computer.
e LED on the rear panel should be lit. If it is not, LINK
verify that you are indeed using a crossover cable, not a standard
Ethernet cable. A standard Ethernet cable should only be used
if you are connecting the RPM 26z and a computer indirectly
using an Ethernet switch. Launch the Drag Net application
and follow the steps to create a new project and new RPM
26z device conguration. Click the Congure Hardware IP
shortcut and follow the instructions to set the unit’s IP address
to be compatible with your computer’s Network settings. Tip: If
you aren't sure what IP to use, try the address 192.168.69.69 and
subnet 255.255.255.0. is nds the default factory address without
manually setting it.
INPUT
AES3 OUTPUT
1 2
A
B
1
43
2
6
5
LOCK
VIP POWER
ETHERNET
S TUSTA
RPM 26z
PROGRAMMABLE
MULTIPROCESSOR
PRESET
24
Now click on the button in the toolbar. A device name Poll
and IP address should appear under the folder in the Live
Project window. If a device does not appear, consult Drag Net’s
online Help for instructions on conguring and verifying your
computer’s Network settings.
e audio path within the RPM 26z is displayed in Drag
Net’s Device Conguration window as a collection of blocks
wired together to form a . ese maps are cre-Processing Map
ated oine as congurations, which are then trans-Storage
ferred to a unit. Drag blocks from the onto the Live Palette
Processing Map and wire them together to create the audio
path. Save this le frequently using the . File > Save command
Transfer the selected conguration to a unit using Storage Live
the Transfer Cong button in the Project window. A new,
minty green Device Conguration window opens once the
transfer is complete, indicating you are now online with a Live
device. Double-click a processing block to display and adjust its
Properties (parameters) in real time on a Live device — there
is no need to go oine to make parameter changes.
Once you have a useful conguration in the unit, connect
balanced audio INPUTS and OUTPUTS to the Euroblocks on
the rear panel, then turn on the amplier. As a precautionary
measure, all outputs are muted during after a conguration and
transfer. Unmute each output individually, or use the handy
Mute Outputs button in the toolbar. Once all outputs are
unmuted, audio passes through the unit along the connections
you dened.
Product specificaties
| Merk: | Rane |
| Categorie: | Niet gecategoriseerd |
| Model: | RPM 26z |
Heb je hulp nodig?
Als je hulp nodig hebt met Rane RPM 26z stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Rane
19 Juni 2025
18 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
Handleiding Niet gecategoriseerd
- DV8 Offroad
- MPM
- Gamma
- A-NeuVideo
- Kontakt Chemie
- Veritas
- Catit
- Rugged Geek
- Rinnai
- AXESS
- Insect Lore
- Narva
- Bar Fly
- Juwel
- Hansgrohe
Nieuwste handleidingen voor Niet gecategoriseerd
22 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025
21 Juni 2025