Randall RG3003H Handleiding

Randall Versterker RG3003H

Lees hieronder de 📖 handleiding in het Nederlandse voor Randall RG3003H (2 pagina's) in de categorie Versterker. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2

A M P L IFIE R S

RM50/RM80

M O D U L A R T U B E C O M B O S

O W N E R S M A N U A L

RANDALL RG3003H

300 Watts @ 4 Ω

3 Channels with Gain and Level

Integrated Noise Gate with Threshold

EQ with Bass,Mid,Treble,Presence

Bass EQ Boost

Mid EQ Scoop

Switchable Serial effects loop

XLR Output with Ground Lift

RF1503 Footswitch switches all three

Channels and Loop

Randall Warranty!

Randall Ampliﬁers, a Division of U.S. Music Corporation warrants the product

you have purchased to be free of defects in materials and workmanship in normal

use for a period of two (2) years from the date of original purchase. This warranty

shall run to the original purchaser when purchased from an Authorized Randall

Dealer. The manufacturer warrants speakers for a period of (1) years. The

manufacturer warrants tubes for a period of (90) days. Defective parts found

during the applicable warranty period with proof of purchase will be replaced or

repaired without charge if the complete product is returned to US Music Corp or

any Authorized Randall Service Center within the U.S.A. Randall reserves the

right to use materials readily available at the time of the repair. All Warranty

service requires Proof of Purchase (sales receipt) to be presented at time of service

request. Any repair or service performed by any person of entity other than an

Authorized Service Center is not covered by this limited warranty. The customer

pays transportation to and from Randall factory service or any Randall Authorized

Service Center. Rental stock is warranted for (1) year from date of invoice to the

Authorized dealer. Warranty on rental units is not transferable.!

What is covered against manufacturing defects!

Parts and Labor to correct any defect in materials used and any defect attributable

to workmanship.!

What is not covered:!

Shipping Damage. Report damage upon receipt of item to the carrier (i.e. UPS).

Freight carrier must be notiﬁed upon receipt of items to insure freight damage

claim resolution. Shipping damage not ﬁled with carriers within (48) hrs upon

receipt will not be covered under warranty. Report any shipping damage within

(48) hrs of receipt to the Randall Customer Service Dept at 1-800-877-6863, ext.

5120. Keep all original documents and packing materials to insure freight damage

claim resolution. Merchandise that has been modiﬁed after original shipment from

the Randall factory. Products whose serial numbers have been altered or removed.

Exterior normal wear and tear damage to the ﬁnish due to misuse, operation

outside the speciﬁed ratings, neglect or accident. Warranty claims by anyone other

than the original purchaser. Randall is not responsible for any items left in

protective covers or cases, (We strongly advise that all personal items such as

chords, cables, tuners, etc… be removed!) freight charges to and from the factory

or an Authorized service center on customer owned goods, any and all charges

incurred from priority service requests (Rush Service) or priority shipping for

replacement parts. Any and all charges if no problem is found.!

Return Authorization!

All items being returned for any reason must have a Return Authorization number.

This RA# must be placed on the outside of the carton of the item being returned or

the carton will be refused upon delivery. Please call the customer service

department at 1-800-877-6863, ext. 5120, for the return authorization number.

Dealer stock items will be returned to the dealer freight prepaid.!

An Authorized Warranty Service Center must perform any and all ﬁeld warranty

service work. Customer will not pay for parts and/or labor provided the problem

found is within warranty guidelines. Proof of purchase must be provided at the

time of service request. Transportation charges to and from the Authorized

Warranty Service Center are the responsibility of the customer. Rush service

charges and special freight charges for required parts are not covered under

warranty and are also the responsibility of the customer. If a unit is not easily

transported to an authorized service center, the customer is responsible for

technician travel charges. Any charges for labor or processing when no problem is

found are also not covered under warranty. Any charges incurred for work

performed by an unauthorized service center are the responsibility of the customer. !

Warranty terms may very per country, check warranty terms

with local Distributor or at point of purchase.

For detailed product videos please visit our

website at :www.randallamplification.com

OPERATION

MANUAL

RG3003H

A M P L IFIE R S

RM50/RM80

M O D U L A R T U B E C O M B O S

O W N E R S M A N U A L

1. 1/4” Guitar Input.

2. Channel selector switch toggles between 3 channels (footswitchable).

3. Channel 1 gain controls amount of pre amp drive to channel 1.

4. Bright switch adds Hi-Frequency EQ “Sparkle” to Channel 1.

5. Channel 1 volume controls the amount of Channel 1 signal being sent to the master volume

output.

6. Channel 2 gain controls amount of pre amp overdrive to channel 2 - this will control the amount of

“distortion”.

7. Channel 2 volume controls the amount of Channel 2 signal being sent to the master volume

output.

8. Channel 3 gain controls amount of preamp overdrive to channel 3 - this will control the amount of

“searing distortion”.

9. Channel 3 volume controls the amount of Channel 3 signal being sent to the master volume

output.

10. The Bass knob controls the amount of low frequency equalization for the entire signal.

11. The BASS BOOST will enhance low EQ - Warning: use of boost with the Bass knob turned up can

cause speaker damage.

12. The Middle knob controls the mid-frequency equalization for the entire signal.

13. The MID SCOOP will decrease middle EQ similar to a “smiley face” setting on a graphic EQ.

14. The Treble knob will control the amount of High frequency equalization for the entire signal.

15. The Presence knob controls the uppermost High EQ frequencies above the Treble EQ shelf.

16. NOISE GATE BYPASS removes the noise suppression circuit from the signal path.

17. THRESHOLD controls the Noise Reduction function. After setting your preferred gain and tone

settings, play your guitar very softly and turn up the threshold until it begins to eliminate the

softest notes then turn it slightly under that “threshold”.

Congratulations on the purchase of your new RANDALL Amplifier! We at Randall Amplification appreciate that you chose the RG3003H Amplifier and wish you

years of great tone and enjoyable playing time. Please review the safety instructions below and be aware that the documentation provided in this manual references

120volt USA versions of the models covered. Note that the POWER listed on the back of the unit should be for your countries’ power standard.

18. The MASTER VOLUME controls the amps volume going to whatever speaker cabinet is

connected.

19. The PHONES output allows for headphones to be plugged in - Note: speaker out is

muted during headphone operation.

20. STEREO MEDIA INPUT allows for 1/8” media source such as MP3 player to be inserted

into signal to play along.

21. The POWER switch turns the amplifier on and off.

22. AC Inlet this jack is for the power cable supplied for your regions power - plug this cable

in and the other side to the source.

23. SPEAKER OUTPUT #1 is parallel with Speaker output #2 and utilizes standard 1/4” with

MINIMUM 4 OHMS LOAD FOR BOTH OUTPUTS #1 & #2 -(this means maximum

2-8ohm cabs combined for both speaker outputs).

24. SPEAKER OUTPUT #2 is parallel with Speaker output #1 and utilizes standard 1/4” with

MINIMUM 4 OHMS LOAD FOR BOTH OUTPUTS #1 & #2 -(this means maximum

2-8ohm cabs combined for both speaker outputs).

25. XLR Line Out provides “mic cable” output to carry amp output signal to PA, mixing

console or recording device.

26. GND LIFT - lifts the ground or “Earth” of the XLR OUT to avoid noise/hum when

interfacing external gear via XLR.

27. EFFECTS LOOP RETURN - plug 1/4” guitar cable from the output from Effects pedal or

device here.

28. EFFECTS LOOP SEND - plug 1/4” guitar cable to the input of Effects pedal or device

here.

29. FOOTSWITCH - 7 PIN DIN connector of included 4 button RF1503 footswitch inserts

here to operate.

Product specificaties

Merk:	Randall
Categorie:	Versterker
Model:	RG3003H

Heb je hulp nodig?

Als je hulp nodig hebt met Randall RG3003H stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Versterker Randall

Randall RG3003H Handleiding

17 April 2023

Handleiding Versterker

Nieuwste handleidingen voor Versterker

Marshall Code 25 Handleiding

16 September 2023

Marshall Code - PEDL-91009 Handleiding

16 September 2023

DAP Audio Palladium Vintage P1200 Handleiding

15 September 2023

Engl Screamer 50 Handleiding

17 September 2023

DAP Audio Palladium P2000 Handleiding

15 September 2023

DAP Audio Palladium P900 Handleiding

15 September 2023

DAP Audio Palladium Vintage P1600 Handleiding

15 September 2023

DAP Audio Palladium Vintage P500 Handleiding

15 September 2023

DAP Audio MPA-4250 Handleiding

15 September 2023

DAP Audio Palladium P1600 Handleiding

15 September 2023