QTX QX10BT Handleiding

QTX Speaker QX10BT

Lees hieronder de đź“– handleiding in het Nederlandse voor QTX QX10BT (4 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
QX BT
Active Speakers with Bluetooth®
Order ref: QX8BT (178.752 ) UK
QX10BT (178.753 ) UK
User Manual
Version 1.1
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
QXBT User Manual
Introduction
Thank you for choosing the QXBT active speaker with Bluetooth™ technology. This versatile active speaker
can deliver playback from a paired Bluetooth device and a mic or line input source simultaneously.
Package Contents
Please check the contents to ensure that the product has been received in good condition with the
appropriate mains lead(s). If you find any accessory is missing or the product has arrived with any
problems, please contact your retailer at once.
Warning
This product contains no us -serviceable parts so make no attempt to try to fix or modify this item er
yourself as this will invalidate the warranty. We recommend you keep the original package and proof of
purchase for any possible replacement or returned demand. To prevent the risk of fire or electric shock, do
not expose this appliance to rain or moisture. To prevent electric shock do not remove the cover. No user
serviceable parts inside. Refer servicing to qualified service personnel.
Safety: Labelling Conventions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
This symbol indicates that dangerous voltage constituting a risk of electric shock
is present within this unit
This symbol indicates that there are important operating and maintenance
instructions in the literature accompanying this unit.
Prior to connecting mains, check the supply voltage is correct and the mains lead is OK.
Avoid ingress of water or particles into the enclosure.
If the mains or D.C. fuse blows, refer the unit to qualified service personnel
Placement
Keep the unit out of direct sunlight and away from heat sources.
Keep the unit away from moisture or dusty environments.
Mount the unit on a stable surface, 35mm pole mount or suspend using the integral flying points.
Ensure that any supporting structures have adequate load capacity for the weight of the unit.
Cleaning
Use a soft cloth with a neutral detergent to clean the cabinet, panel and controls.
To avoid damage, do not use solvents to clean this equipment.
QXBT User Manual
Rear Panel Layout
Operation
Connect any line input (CD, mp3 player, home keyboard etc.) to the QXBT speaker via the 6.3mm jack line
input (12) or alternatively, connect a microphone to the XLR mic input (11)
Turn the VOLUME control (7) down and turn the POWER switch (3) BASS and TREBLE controls fully on.
(8, 9) should remain pointing vertically (12-o-clock position).
Turn up the VOLUME control part way and test the input signal (line or microphone) for output through
the speaker. Adjust the VOLUME to the required output level and TREBLE and BASS controls to adjust the
overall tone of the output (clockwise to boost, anti-clockwise to cut).
Bluetooth™ Connection
QXBT units are fitted with a Bluetooth receiver, which is operated via a rotary control and play b(4) utton
(5) on the rear panel. When the rotary control is turned fully off, power to the Bluetooth receiver is off.
If switched off, turn the Bluetooth rotary control clockwise to switch power on to the Bluetooth receiver.
Turning the rotary control up increases Bluetooth output level halfway is a reasonable position to start –.
Press and hold the Bluetooth play button for 3 seconds and the Bluetooth indicator (6) will flash blue If .
the playback source is already paired, the connection will be made with the QXBT speaker and a chime will
sound to confirm this.
If not paired, press the play button briefly again to see the LED flash between blue and red .
At this point, the Bluetooth receiver is made visible to all Bluetooth devices in range.
Scan for Bluetooth devices on your playback source and check for a device called “ luetooth”b (lower case).
Select this device and opt to connect and your sending device should state that it is connected to
“ luetooth” for audio outputb and the LED should flash blue and a beep will confirm the pairing .
Play audio from your sending device and check for output through the QXBT speaker.
1.
Fig.8 mains inlet
5.
Bluetooth play button
9.
Bass EQ control
2.
Mains fuse holder
6.
Bluetooth indicator
10.
Line output XLRM
3.
Power on/off switch
7.
Volume control
11.
Mic input XLRF
4.
Bluetooth off/volume
8.
Treble EQ control
12.
Line input 6.3mm jack

Product specificaties

Merk: QTX
Categorie: Speaker
Model: QX10BT

Heb je hulp nodig?

Als je hulp nodig hebt met QTX QX10BT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Speaker QTX

QTX

QTX QUEST-12A Handleiding

9 Juli 2023
QTX

QTX QUEST-10A Handleiding

7 Juli 2023
QTX

QTX PartyPod Handleiding

27 April 2023
QTX

QTX QR12K Handleiding

10 April 2023
QTX

QTX QR15K Handleiding

2 April 2023
QTX

QTX QR15PA Handleiding

30 Maart 2023
QTX

QTX QR5B Handleiding

27 Maart 2023
QTX

QTX QX12A Handleiding

21 Maart 2023
QTX

QTX QX12PA+ Handleiding

18 Maart 2023
QTX

QTX QR10PABT Handleiding

16 Maart 2023

Handleiding Speaker

Nieuwste handleidingen voor Speaker

OTTO

OTTO Bluetooth Revo NC2 Handleiding

20 April 2024
REL Acoustics

REL Acoustics Strata Handleiding

20 April 2024
REL Acoustics

REL Acoustics Strata III Handleiding

20 April 2024
Soen

Soen Transit Handleiding

18 April 2024
Miller & Kreisel

Miller & Kreisel MP300RC Handleiding

18 April 2024
Soen

Soen Transit XS Handleiding

18 April 2024
Miller & Kreisel

Miller & Kreisel MP7 Handleiding

18 April 2024
Qian

Qian QRBT1801 Handleiding

17 April 2024
Focal

Focal Twin6 Handleiding

17 April 2024
Kenwood

Kenwood KFC-WPS1000F Handleiding

16 April 2024