Pyle PDIC56 Handleiding

Pyle Speaker PDIC56

Lees hieronder de 📖 handleiding in het Nederlandse voor Pyle PDIC56 (1 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1

IN-CEILING SPEAKER

INSTALLATION MANUAL

www.pyleaudio.com

INSTALLATIONTECHNICAL PARAMETERS

TROUBLESHOOTING

IF T HERE IS NO SOUND FROM ANY OF THE SPEAKERS:

IF T HERE IS NO SOUND COMING FROM ONE SPEAKERS:

IF T HERE IS LOW(OR NO) BASS OUT PUT :

IF T HE SYSTEM PLAYS AT LO W VOLUM ES BUT SHUT S OFF AS VOLUM E IS INCREASED:

TOOLS NEEDED

The in-wall/in-ceiling speakers

were designed to be easily

installed.However,if you are

unsure of your ability to prop-

erly install these loudspeakers

please contact your dealer or a

quali fied installer.

Pencil Phillips #2 screwdriver

Measuring tape Utility knife

Carpenter’s level Awl

Check that receiver/amplifier is on and a source is playing.

Check all wires and connections between receiver/amplifier and speakers.Make sure all wires are connected.Make

sure none of the speaker wires are frayed,cut,punctured or tounching each other.

Review proper proper operation of your receiver/amplifier.

Check the“Balance”control on your receiver/amplifier.

Check allwires and connections between receiver/amplifier and speakers.Make sure all wires are connected.Make

sure none of the speaker wires are frayed,cut,punctured or tpunching each other.

Make sure the connections to the left and right“speaker Inputs”have the correct polarity(+ and -).

Consider adding a powered subwoofer to your system.

In Dolby Digital or DT S modes,make sure your receiver/processor is corectly configured.When using a subwoofer,

make sure thesubwoofer output of the receiver/processor has been enabled.If no subwoofer is being used,

make sure the left and right front and rear speakers have been configured as“LARGE”See your receiver/processor’s

owner’s manual for futher information on correct speaker configuration in Dolby Digital,DTS and other surround sound

modes.

Check all wires and connections between receiver/amplifier and speakers.Make sure all wires are connected.Make

sure none of the speaker wires are frayed,cut,punctured or touching each other.

If more than one pair of main speakers is being used,check the minimum-impedance requirements of your

receiver/amplifier.

Thank you for purchasing this PYLE in-wall/in-ceiling speaker system.It is a

state-of-the-art product carefully designed and manuf act ured for your installation

needs,and has been t horoughly tested to ensure consistent and reliable perfor-

mance.

If you have any question about the installation or operation of your PYLE

in-wall/in-ceiling speaker system which are not answered by this manual,contact

your dealer immediately.

INCLUDED

SPEAKER CONNECTIONS

REAR SPEAKERS

IN- CEILING

CONNECTION TIPS

SPEAKER PLACEMNT

IN- CEILING SPEAKERS

EXISTING CONSTRUCTION

IN- CEILING SPEAKERS

FRONT SPEAKERS

srtips of

adhesive Screws Tem plate

One pair of speakers with grilles.

One pc of speakers with grills

for PDIC56/PDIC66/PDIC86/PDIC106

M4x60mm

4pcs

40 60

0 0

WALL

5-6FT

WALL WALL WALL WALL

LEFT RIGHT

Front or Rear S peaker Outputs

Proper placement of the speakers is an imporant step in obtaining

the most realistic sound stage possible.These recommendations are

for the optimum placement of the londspeakers.Use these placement

recommendations as a guide. Slight variations will not diminish your

listening pleasure.The front speakers should be placed the same di--

stance from each other as they are from the listening position.They

should be placed at about the same height from the floor as the liste-

ner’s ears will be,with the tweeters aimed toward the listener at ear-level height.In a home theater configu-

ration,the two surround,speakers should be placed slightly behind the listening position and ideally should

face each other and be at a level higher than the listener’s ears.If that is not possible,they may be placed in

a wall(or in the ceiling)behind the listening position,facing forword.The surround speakers should not call

attention to themselves.T hey should provide a diffuse,ambient sound accompanying the main program mat-

erial heard in the front speakers. In Dolby*Digital and DTS systems,aim the tweeters toward the listening

position at ear-level height.

The wires for bot h speakers

should be the same length.If

one speaker is placed closer to

the amplifer than the other,

hide the excess wire behid

the wall.Speakers and elec-

tronics terminals have corre-

sponding(+)and(-)terminals.

We use red to denote the(+)termi-

nal and black for t he(-)termi-

nal.It is important to connect

both speakers identically:(+)on

the speaker to(+)on the ampli-

fier and(-)on the speaker to(-)

on the amplifier.Wireing “out

of phase” result s in thin sound,

weak bass and a poor stereo

image.With t he advent of mult i-

channel surround sound

systems,connecting all of the

speakers in your system with

the correct polarity remains

equally important in order to

preserve the proper ambience

and directionality of the

program material.

５．２５＂　２－Ｗａｙ　Ｃｅｉｌｉｎｇ　Ｓｐｅａｋｅｒ　Ｓｙｓｔｅｍ

＊Ｂｌａｃｋ　ＰＰ　Ｃｏｎｅ　Ｗｉｔｈ　Ｒｕｂｂｅｒ　Ｅｄｇｅ

＊１／２＂　Ｔｉｔａｎｉｕｍ　Ｄｏｍｅ　Ｔｗｅｅｔｅｒ　Ｉｎ　Ｓｗｉｖｅｌ　Ｍｏｕｎｔ

＊Ｐｏｗｅｒ：　１５０　Ｗａｔｔｓ　Ｒａｔｅｄ　Ｐｅａｋ

＊Ｆｒｅｑｕｅｎｃｙ　Ｒｅｓｐｏｎｓｅ：　８０ＨＺ－２０ＫＨＺ

＊Ｉｍｐｅｄａｎｃｅ：　８　Ｏｈｍｓ

＊Ｓｅｎｓｉｔｉｖｉｔｙ：　８８　ｄＢ　　　

＊ｗｉｔｈ　Ｅｌｅｃｔｒｏｎｉｃ　Ｃｒｏｓｓｏｖｅｒ　Ｎｅｔｗｏｒｋ

＊Ｓｕｐｐｌｉｅｄ　Ｗｉｔｈ　Ｒｏｕｎｄ　Ｇｒｉｌｌｅｓ　Ａｎｄ　Ｓｑｕａｒｅ　Ｇｒｉｌｌｅｓ

＊Ｓｉｚｅ：　Ｒｏｕｎｄ　／　Ｓｑｕａｒｅ　Ｇｒｉｌｌｅｓ：　８　　”／８　　　”＊８　　”　　　　

＊Ｃｕｔｏｕｔ　Ｓｉｚｅ：６　　” 　　

＊Ｍｏｕｎｔｉｎｇ　Ｄｅｐｔｈ：３ ”　　

ＰＤＩＣ５６ＰＤＩＣ６６

ＰＤＩＣ８６ＰＤＩＣ１０６

４

５／

３

１０／３

１０／

６．５＂　２－Ｗａｙ　Ｃｅｉｌｉｎｇ　Ｓｐｅａｋｅｒ　Ｓｙｓｔｅｍ

＊Ｂｌａｃｋ　ＰＰ　Ｃｏｎｅ　Ｗｉｔｈ　Ｒｕｂｂｅｒ　Ｅｄｇｅ

＊１／２＂　Ｔｉｔａｎｉｕｍ　Ｄｏｍｅ　Ｔｗｅｅｔｅｒ　Ｉｎ　Ｓｗｉｖｅｌ　Ｍｏｕｎｔ

＊Ｐｏｗｅｒ：　２００　Ｗａｔｔｓ　Ｒａｔｅｄ　Ｐｅａｋ

＊Ｆｒｅｑｕｅｎｃｙ　Ｒｅｓｐｏｎｓｅ：　６０ＨＺ－２０ＫＨＺ

＊Ｉｍｐｅｄａｎｃｅ：　８　Ｏｈｍｓ

＊Ｓｅｎｓｉｔｉｖｉｔｙ：　８９　ｄＢ　　　

＊ｗｉｔｈ　Ｅｌｅｃｔｒｏｎｉｃ　Ｃｒｏｓｓｏｖｅｒ　Ｎｅｔｗｏｒｋ

＊Ｓｕｐｐｌｉｅｄ　Ｗｉｔｈ　Ｒｏｕｎｄ　Ｇｒｉｌｌｅｓ　Ａｎｄ　Ｓｑｕａｒｅ　Ｇｒｉｌｌｅｓ

＊Ｓｉｚｅ：　Ｒｏｕｎｄ　／　Ｓｑｕａｒｅ　Ｇｒｉｌｌｅｓ：　９　　”／９　　　”＊９　　”　　　　

＊Ｃｕｔｏｕｔ　Ｓｉｚｅ：８ ”　　

＊Ｍｏｕｎｔｉｎｇ　Ｄｅｐｔｈ：３ ”　　

１

２／１

２／

８＂　２－Ｗａｙ　Ｃｅｉｌｉｎｇ　Ｓｐｅａｋｅｒ　Ｓｙｓｔｅｍ

＊Ｂｌａｃｋ　ＰＰ　Ｃｏｎｅ　Ｗｉｔｈ　Ｒｕｂｂｅｒ　Ｅｄｇｅ

＊１／２＂　Ｔｉｔａｎｉｕｍ　Ｄｏｍｅ　Ｔｗｅｅｔｅｒ　Ｉｎ　Ｓｗｉｖｅｌ　Ｍｏｕｎｔ

＊Ｐｏｗｅｒ：　２５０　Ｗａｔｔｓ　Ｒａｔｅｄ　Ｐｅａｋ

＊Ｆｒｅｑｕｅｎｃｙ　Ｒｅｓｐｏｎｓｅ：　４０ＨＺ－２０ＫＨＺ

＊Ｉｍｐｅｄａｎｃｅ：　８　Ｏｈｍｓ

＊Ｓｅｎｓｉｔｉｖｉｔｙ：　８９　ｄＢ　　　

＊ｗｉｔｈ　Ｅｌｅｃｔｒｏｎｉｃ　Ｃｒｏｓｓｏｖｅｒ　Ｎｅｔｗｏｒｋ

＊Ｓｕｐｐｌｉｅｄ　Ｗｉｔｈ　Ｒｏｕｎｄ　Ｇｒｉｌｌｅｓ　Ａｎｄ　Ｓｑｕａｒｅ　Ｇｒｉｌｌｅｓ

＊Ｓｉｚｅ：　Ｒｏｕｎｄ　／　Ｓｑｕａｒｅ　Ｇｒｉｌｌｅｓ：　１１　　” ／１１　　　” ＊１１　　”　　　　

＊Ｃｕｔｏｕｔ　Ｓｉｚｅ：９　　” 　　

＊Ｍｏｕｎｔｉｎｇ　Ｄｅｐｔｈ：３　　”　　

２

５

／

１５

／

１

２／

１５

／１５

／

１０＂　２－Ｗａｙ　Ｃｅｉｌｉｎｇ　Ｓｐｅａｋｅｒ　Ｓｙｓｔｅｍ

＊Ｂｌａｃｋ　ＰＰ　Ｃｏｎｅ　Ｗｉｔｈ　Ｒｕｂｂｅｒ　Ｅｄｇｅ

＊１／２＂　Ｔｉｔａｎｉｕｍ　Ｄｏｍｅ　Ｔｗｅｅｔｅｒ　Ｉｎ　Ｓｗｉｖｅｌ　Ｍｏｕｎｔ

＊Ｐｏｗｅｒ：　３００　Ｗａｔｔｓ　Ｒａｔｅｄ　Ｐｅａｋ

＊Ｆｒｅｑｕｅｎｃｙ　Ｒｅｓｐｏｎｓｅ：　３５ＨＺ－２０ＫＨＺ

＊Ｉｍｐｅｄａｎｃｅ：　８　Ｏｈｍｓ

＊Ｓｅｎｓｉｔｉｖｉｔｙ：　８９　ｄＢ　　　

＊ｗｉｔｈ　Ｅｌｅｃｔｒｏｎｉｃ　Ｃｒｏｓｓｏｖｅｒ　Ｎｅｔｗｏｒｋ

＊Ｓｕｐｐｌｉｅｄ　Ｗｉｔｈ　Ｒｏｕｎｄ　Ｇｒｉｌｌｅｓ　Ａｎｄ　Ｓｑｕａｒｅ　Ｇｒｉｌｌｅｓ

＊Ｓｉｚｅ：　Ｒｏｕｎｄ　／　Ｓｑｕａｒｅ　Ｇｒｉｌｌｅｓ：　１２　　”／１２　　”＊１２　　” 　　　　

＊Ｃｕｔｏｕｔ　Ｓｉｚｅ：１０　　”　　

＊Ｍｏｕｎｔｉｎｇ　Ｄｅｐｔｈ：３　　　”　　

４５

／

４

５／

１

２

／

４

５

／４

５

／

Ｔｈｉｓ　ｐｒｏｄｕｃｔ　ｇｅｔｓ　ｔｈｅ　ｐａｔｅｎｔ　ｏｆ　ｉｎｎｏｖａｔｉｏｎ　ｏｆ　ｔｈｅ　ｓｔｒｕｃｔｕｒｅ，　ｅａｓｙ　ｆｏｒ　　ｉｎｓｔａｌｌａｔｉｏｎ．

Ｕｓｅ　ｎｅｗ　ｅｎｖｉｒｏｎｍｅｎｔａｌ　ｐｒｏｔｅｃｔｉｏｎ　ＡＢＳ　ｍａｔｅｒｉａｌ，　ｗｉｔｈ　ｌｏｎｇｅｒ　ｓｅｒｖｉｃｅ　ｌｉｆｅ，　ｎｏｔ　ｅａｓｙ　ｔｏ　ｃｈａｎｇｅ　ｃｏｌｏｒ．

Cut the drywall.

Note:Always allow at least

one- half inch between a wall

stud and the speaker cutout or

the locking tabs will not be able

to swivel into place.

Connect the speaker wires to

the speaker.

Replace the metal grille. Complete.

Screw d own each of the four

Phillips head screws.The

locking tabs will swivel into

place and secure the unit to

the rear surface of the drywall.

Put in the strips of adhesive to

secure the grille.

-2- - 3- -4- -5- - 6-

1600-63rd Street

Brooklyn,NY 11204 USA

Product specificaties

Merk:	Pyle
Categorie:	Speaker
Model:	PDIC56
Kleur van het product:	Wit
Gewicht:	2409 g
Hoogte:	76.19 mm
Connectiviteitstechnologie:	Bedraad
Diameter:	210.82 mm
Gemiddeld vermogen:	- W
Impedantie:	8 Ohm
Geschikt voor buitengebruik:	Nee
Audio-uitgangskanalen:	2.0 kanalen
Speaker plaatsing:	Inbouw in de muur/plafond
Aantal drivers:	2
Woofer:	Ja
Peak Music Power Output (PMPO):	150 W
Frequentiebereik:	80 - 20000 Hz
Gevoeligheid:	88 dB
Luidspreker soort:	2-weg
Diameter woofer:	5.25 "
Diameter hogetonenluidspreker:	0.5 "
Tweeter:	Ja
Driver cone material:	Polypropyleen