PowerWalker AVR 600 Handleiding
PowerWalker
Niet gecategoriseerd
AVR 600
Bekijk gratis de handleiding van PowerWalker AVR 600 (5 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 9 mensen en kreeg gemiddeld 5.0 sterren uit 5 reviews. Heb je een vraag over PowerWalker AVR 600 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/5
Automac Voltage Regulator (AVR)
PowerWalker AVR 1200
PowerWalker AVR 1000
PowerWalker AVR 600
Quick Start Guide
EN
1. Introducon
Thank you for purchasing PowerWalker product. This series is designed to automacally maintain a
constant voltage level to protect sensive electronics from brownouts and overvoltages. With its
fashionable and exible cabinet, it can be installed on a desk or wall without causing an unsightly or
unprofessional image, and will perfectly ulize a limited working environment. This series oers
one-step boost and one-step buck stabilizer to connuously supply a clean power source to its
connected equipment.
2. Product Overview
1. Output receptacles (for connected equipment)
2. AC Input 5. Power Switch
3 Circuit breaker 6. Power LED .
4 .Modem/phone line surge protecon 7. Boost/Buck LED
Wall Mount the Unit
The unit can be mounted to a wall surface. Please follow below steps:
1. Use tape to hold this page in place against the wall.
2. Use a sharp nail to puncture the center of the two holes to mark the wall.
(see below chart 1)
3. Mount the unit by posioning the key-hole slots over the mounng nails.
(see chart 2)
EN
3. Installaon and Inial Startup
Inspecon
Remove the unit from the shipping package and inspect it for damage that may occur during
transportaon. Nofy the carrier and place of purchase if any damage is found.
Placement & Storage Condions
Install the unit in a protected area that is free of excessive dust and has adequate air ow. Please
place the AVR away from other units at least 2.5cm to avoid interference. Do NOT block the top or
side air vents on the unit.
Do not operaon the unit in an environment where the ambient temperature or humidity is outside
the limits listed in the specicaons. Operate the unit in an environment free of excessive dust,
mechanical vibraon, inammable gases and explosive or corrosive atmospheres.
Connect to the Wall Outlet
Plug the input power cord of the unit to the wall outlet.
Connect the Loads
Plug in the loads to output receptacles of the unit and switch the unit “ON” by pressing the
side panel ON/OFF switch to “ON” posion. Then the connected devices will be powered.
Connect Modem/Phone for Surge Protecon (Only for the model with RJ-11)
Connect a single modem/phone line into surge-protected “IN” outlet on the unit. Connect
from “OUT” outlet to the computer with phone line cable.
Turn On/O the Unit
Turn on the unit by pressing the power switch to “ON” (l)posion. This switch may be
used as the master ON/OFF switch for all connected devices.
EN
Product specificaties
| Merk: | PowerWalker |
| Categorie: | Niet gecategoriseerd |
| Model: | AVR 600 |
Heb je hulp nodig?
Als je hulp nodig hebt met PowerWalker AVR 600 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd PowerWalker
22 Mei 2025
22 Mei 2025
22 Mei 2025
21 Mei 2025
21 Mei 2025
21 Mei 2025
21 Mei 2025
21 Mei 2025
21 Mei 2025
Handleiding Niet gecategoriseerd
- DNA
- Apple
- Silva
- Compex
- KoolScapes
- SVS
- Magic Care
- Crivit
- Brother
- VAIS
- Ultimate Support
- Opus
- Clarke
- Quartet
- HPI Racing
Nieuwste handleidingen voor Niet gecategoriseerd
23 Juli 2025
23 Juli 2025
22 Juli 2025
22 Juli 2025
22 Juli 2025
22 Juli 2025
22 Juli 2025
22 Juli 2025
22 Juli 2025
22 Juli 2025