Planet POE-E101 Handleiding

Planet Wifi-repeater POE-E101

Lees hieronder de 📖 handleiding in het Nederlandse voor Planet POE-E101 (4 pagina's) in de categorie Wifi-repeater. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

- 1 -

- 2 -

- 3 -

- 4 -

- 5 -

- 6 -

- 7 -

- 8 -

Introduction

1.1 Packet Contents

Thank you for purchasing PLANET POE-E101 IEEE

802.3af Power over Ethernet Extender, your Power

over Ethernet Extender package shall contains following

contents:

Check the contents of your package for following parts:

Power over Ethernet Extender x 1

User's Manual x 1

If any of these pieces are missing or damaged, please

contact your dealer immediately, if possible, retain the

carton including the original packing material, and use

them against to repack the product in case there is a

need to return it to us for repair.

1.3 TechnicalSpecication

Model POE-E101

Interfaces

LAN IN

1 x 10/100Base-TX Ethernet with IEEE

802.3af PoE “Data + DC” in Auto

MDI/MDI-X, Auto-negotiation RJ-45

connector

LAN OUT

1 x 10/100Base-TX Ethernet with IEEE

802.3af PoE “Data + DC” out Auto

MDI/MDI-X, Auto-negotiation RJ-45

connector

Power over Ethernet

PoE

Standard IEEE 802.3af Power over Ethernet

PoE Power

Supply Type Mid-Span / Type B

PoE Power

Output 48V DC, 270mA, Max. 13 Watts

Power Pin

Assignment 4/5(+), 7/8(-)

2.2 Ports Connection

IN Port

Connect the PoE IN port from following

802.3af PSE device through a CAT-5e/6

UTP cable:

• PoE Injector

• PoE Injector Hub

• PoE Ethernet Switch

• Previous POE-E101

OUT Port

Connect the PoE OUT port to following

802.3af PD device through a CAT-5e/6

UTP cable:

• PoE IP Camera

• PoE VoIP Phone

• PoE Wireless AP

• PoE Splitter

• Next POE-E101

2.3 LEDDenition:

LED Color Function

PoE IN Green Lights to indicate the port is

providing 48V DC in-line power.

LNK/

ACT Green

Lights

indicate

the

port

is link up.

Blink: indicate that the extender is

actively sending or receiving data

over port.IN

PoE

OUT Green Lights to indicate the port is

providing 48V DC in-line power.

Standards Conformance

Regulation

Compliance FCC Part 15 Class A, CE

Standard

Compliance

IEEE 802.3 10Base-T Ethernet

IEEE 802.3u 10/100Base-TX Fast

Ethernet

IEEE 802.3af Power over Ethernet PSE

/ Mid-Span

IEEE 802.3af Power over Ethernet PD /

Mid-Span

IEEE 802.3x Flow Control

Environment

Operating

Temperature:

0 ~ 50 Degree C

Relative Humidity:

0 ~ 95% (non-condensing)

Storage

Temperature:

-40 ~ 85 Degree C

Relative Humidity:

5 ~ 95% (non-condensing)

1.2 Key Features

Complies with IEEE 802.3af Power over Ethernet

Extends the range of PoE an additional 100 meters

(328ft.)

Forwards both Ethernet data and PoE power to

remote device

Auto-detect and protect of PoE equipment from being

damaged by incorrect installation

Multiple units, daisy-chain installation support

No external power cable installation required

Compact size, Wall-mountable design

Plug-and-Play installation

Hardware Specication

Data Rate 10/100Mbps

Switch

Architecture Store-and-Forward

Switch

Throughput 148810pps@64Bytes

Latency 7.840µs

Maximum

Frame Size 1552Bytes

Flow Control Back pressure for Half-Duplex

IEEE

802.3x

Pause

Frame

for

Full-Duplex

LED

Indicators

• 1 x PoE IN (Green)

• 1 x LAN Data (Green)

• 1 x PoE OUT (Green)

Protection ESD (Ethernet) : 6KV (TBD)

Surge (EFT for power) : 6KV (TBD)

Dimension

(W x D x H) 94 x 70 x 26 mm

Weight 215g

Power

Requirement

IEEE 802.3af compliant with voltage

within 44V-56V DC

Power

Consumption 2 Watts (system maximum)

Mechanical Metal / Wall Mountable

Cable TIA/EIA-568, Category 5/5e cable

Hardware Description

2.1 Product Outlook

Hardware Installation

This product provides two different running speeds –

10Mbps, 100Mbps in the same device and automatically

distinguishes the speed of incoming connection.

This section describes the hardware features of

POE-E101. Before connecting any network device to the

POE-E101, read this chapter carefully.

3.1 Before Installation

Before your installation, it is recommended to check

your network environment. If there is any far away IEEE

802.3af devices need to power on, the POE-E101 can

provide you a way to supply power for this Ethernet

device conveniently and easily.

The POE-E101 is installed between the PSE (Power Source

Equipment) and the PD (Powered Device); it is powered

by PSE and forwards the Ethernet data and remaining

POE power to the PD. The POE-E101 doesn’t require

an external power supply and it can be installed easily

just plug and play; that means the operator does not

need to congure the POE-E101. The POE-E101 injects

power to the PDs without affecting the data transmission

performance. It offers a cost effective and quick solution

to extend power and data an additional 100m.

Note

The POE-E101 can be installed with third-party

device if the device complied with IEEE 802.3af

standard.

- 9 -

- 10 -

- 11 -

- 12 - - 13 - - 14 -

3.2 Connect POE-E101 to the Power Source

Equipment (PSE)

There are 2 RJ-45 ports in the PoE Extender, of which

the port functions as “IN” “PoE (Data and Power)

input" ”OUT” and the port on the other side functions

as “PoE (Data and Power) output”.

Step 1: Connect a standard CAT-5e/6 UTP cable from

Power Source Equipment (PSE), such as

PoE Switch, PoE Injector hub and single port

PoE injector, to the “IN” port of POE-E101.

Step 2: The PSE delivers both Ethernet Data and PoE

power over UTP cable to the POE-E101 and the

“PoE IN” LED will be steady on.

Note

1. The PoE IN LED turn on steady green means

POE-E101 is being powered successfully with

PoE class 0.

2. If PoE IN LED does not turn on, please check

the remote PSE or the cable with a PC or a

network device to see if the cable is correct.

Or with an 802.3af device such as the target

PD to check the power injection is correct

either.

3.4 Multiple PoE Extender Installation

The POE-E101 PoE Extender supports multiple units,

daisy-chain installation. They can be employed in

series for even longer distances based on remote

PoE IP Camera or PoE Wireless Access Point power

requirement.

Step 1: Connect the additional CAT-5e/6 cable from

the “OUT” port of the rst POE-101, the other

end of the UTP cable be used to connect to the

“IN” port of remote / next POE-E101.

Step 2: “PoE OUT” The LED indicator of the rst

POE-101 will be steady to shows it is providing

power to next PoE Extender.

Step 3: “PoE IN” The LED on the next POE-101 will

steady on.

Step 4: Connect the additional CAT-5e/6 cable to the

remote PoE powered device to the “OUT” port

of next or third POE-E101.

3.3 Connect POE-E101 to the Powered

Device (PD)

Step 3: Connect the additional CAT-5e/6 cable that

will be used to connect to the remote Powered

Device (PD) to the “OUT” port of POE-E101.

Step 4: The “OUT” port is also the power injectors

which transmit DC Voltage to the CAT-5e/6

cable and transfer data and power

simultaneously between the PSE and PD.

Step 5: Once POE-E101 detects the existence of an

IEEE 802.3af device, the “PoE OUT” LED

indicator will be steady, ON to shows it is

providing power.

PoE IP Camera PoE Injector

POE-E101

PoE Extender

PoE P oE

100 meters100 meters

200 meters

PoE

100Base-TX UTP with PoE

100Base-TX UTP

DC Power Line (DC)

Power Line (AC)

Note

1. If the connected device is not fully complying

with IEEE 802.3af standard or in-line

power device, the PoE OUT LED indicator of

POE-E101 will not be steady on.

2. According to IEEE 802.3af standard, the

POE-E101 will not inject power to the cable

if not connecting to a standard IEEE 802.3af

device.

POE-E101

PoE Extender

PoE Ethernet Switch/

Injector Hub

PoE

100 meters100 meters100 meters

100 meters100 meters

PoE Access Point

PoE IP Camera

Non-PoE IP Camera

PoE Splitter

100 meters100 meters

Power Output

300 meters 200 meters 100 meters 0 meters

PoE

100Base-TX UTP with PoE

100Base-TX UTP

DC Power Line (DC)

Power Line (AC)

POE-E101

PoE Extender

POE-E101

PoE Extender

POE-E101

PoE Extender

Note

1. Per POE-E101 will take 2 watts maximum

for the system itself, please check the total

power consumption of your 802.3af PD

and the POE-E101 before you make the

daisy-chain connection. If the overall power

consumption is overloaded, the local PSE

could shutdown the whole power system.

2. Per POE-E101 cable segment is limited in 100

meters CAT-5e/6 UTP wire from its IN/OUT

port to the other data end, use of any other

non standard cable or over distance could

results in unstable connection.

3.5 Optional - DIN-Rail mounting

There are two DIN-Rail holes on the left side of the

POE-E101 that allows the converter can be easily

installed with DIN-Rail mounting. The PLANET optional

DIN-Rail mounting Kit – RKE-DIN can be order

separately. When need to replace the wall mount

application with DIN-Rail application on the POE-E101,

please refer to following gures to screw the DIN-Rail on

the converter. To hang the POE-E101, follow the below

steps:

Step 1: screw the DIN-Rail on the POE-E101.

Step 2: Lightly press the button of DIN-Rail into the

track.

Step 3: Check the DIN-Rail is tightly on the track.

You must use the screws supplied with

the mounting brackets. Damage caused to

the parts by using incorrect screws would

invalidate your warranty.

Product specificaties

Merk:	Planet
Categorie:	Wifi-repeater
Model:	POE-E101
Kleur van het product:	Blauw
Gewicht:	215 g
Breedte:	94 mm
Diepte:	70 mm
Hoogte:	26 mm
Soort:	Netwerkzender & -ontvanger
Materiaal behuizing:	Metaal
LED-indicatoren:	LAN,PoE
Montagewijze:	Muur
Aantal Ethernet LAN (RJ-45)-poorten:	2
Certificering:	FCC Part 15 Class A, CE
Plug and play:	Ja
Bekabelingstechnologie:	10/100Base-T(X)
Netwerkstandaard:	IEEE 802.3,IEEE 802.3af,IEEE 802.3u,IEEE 802.3x
Temperatuur bij opslag:	-10 - 85 °C
Luchtvochtigheid bij opslag:	5 - 95 procent
Power over Ethernet (PoE):	Ja
Maximaal bereik:	300 m
Overdrachtssnelheid:	100 Mbit/s
Auto MDIX IEEE:	Ja
Stroomverbruik (typisch):	2 W
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Ondersteundende kabel types:	Cat5,Cat5e,Cat6
Duplex systeem:	Volledig