Planet ISW-800T Handleiding

Planet Niet gecategoriseerd ISW-800T

Lees hieronder de 📖 handleiding in het Nederlandse voor Planet ISW-800T (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

- 1 - - 2 - - 3 - - 4 -

1. Package Contents

Thank you for purchasing PLANET industrial 5-/8-port 10/100TX

Compact Ethernet Switch, ISW-500T/800T. In the following section, the

term “Industrial Ethernet Switch” means the ISW-500T or ISW-800T.

Open the box of the Industrial Ethernet Switch and carefully unpack it.

The box should contain the following items:

Industrial Ethernet Switch x 1 User’s Manual x 1

DIN-rail Kit x 1 Wall-mount Kit x 1 RJ45 Dust Cap

ISW-500T x 5

ISW-800T x 8

If any of these are missing or damaged, please contact your dealer

immediately; if possible, retain the carton including the original packing

material, and use them again to repack the product in case there is a

need to return it to us for repair.

2.ProductSpecications

Product ISW-500T ISW-800T

Hardware Specications

Copper Ports 5 10/100BASE-TX RJ45

auto-MDI/MDI-X ports

8 10/100BASE-TX RJ45

auto-MDI/MDI-X ports

Switch Architecture Store-and-Forward

Switch Fabric 1Gbps (non-blocking) 1.6Gbps (non-blocking)

Throughput

(packet per second) 0.74Mpps@ 64 bytes 1.19Mpps@ 64 bytes

Address Table 1K entries, automatic source address learning

and aging

Shared Data Buer 448K bits

Flow Control IEEE 802.3x pause frame for full-duplex

Back pressure for half-duplex

ESD Protection 6KV DC

Enclosure IP30 metal case

Installation DIN-rail kit and wall-mount kit

Connector

Removable 6-pin terminal block for power input

Pin 1/2 for Power 1, Pin 3/4 for fault alarm, Pin

5/6 for Power 2

Alarm One relay output for power failure.

Alarm relay current carry ability: 1A @ 24V DC

LED Indicator

System:

Power 1 (Green), Power 2 (Green)

Fault Alarm (Red)

Per 10/100TX RJ45 Ports:

10/100 LNK/ACT (Green)

Dimensions

(W x D x H) 30 x 70 x 104 mm 41 x 70 x 115 mm

Weight 255g 300g

Power Requirements Dual 12~48V DC, 24V AC

Power Consumption Max. 2 watts/6.86BTU

(Ethernet full loading)

Max. 2.5 watts/8.57BTU

(Ethernet full loading)

Standards Conformance

Regulatory

Compliance FCC Part 15 Class A, CE

Stability Testing

IEC60068-2-32 (free fall)

IEC60068-2-27 (shock)

IEC60068-2-6 (vibration)

Standards Compliance

IEEE 802.3 10BASE-T

IEEE 802.3u 100BASE-TX/100BASE-FX

IEEE 802.3x ow control and back pressure

IEEE 802.1p Class of Service

IEEE 802.3az Energy Ecient Ethernet (EEE)

Environment

Operating

Temperature -40 ~ 75 degrees C

Storage Temperature -40 ~ 85 degrees C

Humidity 5 ~ 95% (non-condensing)

3. Hardware Introduction

3.1 Three-View Diagram

The three-view diagram of the Industrial Ethernet Switch consists

of ve or eight auto-sensing 10/100/BASE-TX RJ45 port and one

removable 6-pin terminal block. The LED indicators are also located

on the front panel.

104.00

30.00

70.00

18.00

9.00

91.00

52.00 52.00

50.00

30.00

28.00

48.80 40.00

18.00

40.00

18.00

147.00

Mounting Kit

DIN-Rail Kit

Unit: mm

Rear ViewSide View Side View

Top View

Front View

Bottom View

P1 P2 Fault

ACTLNK

10/100

Max . F ault Alarm Loa ding: 24V, 1A

DC Inp ut: 12-48V

, 0.17A max .

AC Inpu t: 24V

, 0.15A max .

Fault

V1+ V2 +

PWR 2PWR 1

Figure 1: ISW-500T Three-View Diagram

115.00

41.00

70.00

18.00

9.00

103.00

28.65

27.19

70.00

40.00 48.80 40.00

28.00 18.00 28.00

159.00

Top View

Front View

Mounting Kit

DIN-Rail Kit

Unit: mm

Rear View

Bottom View

Side View Side View

P1 P2 Fault

ACTLNK

10/100

Max . Fault Alar m Lo ading: 24V, 1A

DC In put: 12-48 V

, 0.2A max .

AC Inpu t: 24V

, 0.16A max .

Fault

V1+ V2 +

PWR 2PWR 1

Figure 2: ISW-800T Three-View Diagram

[ISW-500T]

1. Insert positive and negative DC power wires into contacts 1 and 2 for

Power 1, or 5 and 6 for Power 2.

Max. Fault Alarm Loading: 24V, 1A

DC nput: 12-48V

, 0.17A max.

AC I ut: 24V

, 0.15A max.

Fa ult

V1+ V2+

PWR2PWR1

1 2 3 4 5 6

Wire Range Wire Type Torque In-lbs (N.m)FW

12-24 AWG Str/Sol 5 (0.56)Cu 2

2. This product is intended to be supplied with a UL-listed power adapter

or power source, rated 24V AC 50/60Hz min. 0.15A or 12-48V DC

min. 0.17A, and Tma 75°C (max.).

3. Tighten the wire-clamp screws for preventing the wires from loos-

ening.

123456

Power 1 Fault Power 2

+ - + -

Note

1. The power input range is 12V ~ 48V DC and supports

24V AC.

2. Use one power input when using 24V AC.

Note

1. La plage d’entrée d’alimentation est de 12V ~ 48V DC

et prend en charge 24V AC.

2. Utilisez une entrée d’alimentation lorsque vous utilisez

24V AC.

[ISW-800T]

1. Insert positive and negative DC power wires into contacts 1 and 2 for

POWER 1, or contacts 5 and 6 for POWER.

Max. Fault Alarm Loading: 24V, 1A

D nput: 12-48V

, 0.2A max.

AC I ut: 24V

, 0.16A max.

Fa ult

V1+ V2+

PWR2PWR1

1 2 3 4 5 6

Wire Range Wire Type Torque In-lbs (N.m)FW

12-24 AWG Str/Sol 5 (0.56)Cu 2

2. This product is intended to be supplied with a UL-listed power adapter

or power source, rated 24V AC, 50/60Hz min. 0.16A or 12-48V DC,

min. 0.2A, and Tma 75°C (max.).

3. Tighten the wire-clamp screws for preventing the wires from loos-

ening.

123456

Power 1 Fault Power 2

+ - + -

Note

1. The power input range is 12V ~ 48V DC and supports

24V AC.

2. Use one power input when using 24V AC.

Note

1. La plage d’entrée d’alimentation est de 12V ~ 48V DC

et prend en charge 24V AC.

2. Utilisez une entrée d’alimentation lorsque vous utilisez

24V AC.

3.2 Front View

P1 P2 Fault

ACTLNK

10/100

P1 P2 Fault

ACTLNK

10/100

Figure 3: ISW-500T Front View ISW-800T Front ViewFigure 4:

3.3 LEDDenition:

System

LED Color Function

DC1 Green Lights to indicate DC power input 1 has power.

DC2 Green Lights to indicate DC power input 2 has power.

Fault Red Lights to indicate that AC or DC power has failed.

Per 10/100BASE-TX Port

LED Color Function

10/100

LNK/ACT Green

Lights

Indicating the port is running at

10/100Mbps speed and successfully

established.

Blinks Indicating that the switch is actively

sending or receiving data over that port.

3.4 Top View

Max. Fault Alarm Loading: 24V, 1A

DC Input: 12-48V

, 0.17A max.

AC Input: 24V

, 0.15A max.

Fa ult

V1+ V2+

PWR2PWR1

1 2 3 4 5 6

Figure 5: ISW-500T Top View

Max. Fault Alarm Loading: 24V, 1A

DC Input: 12-48V

, 0.2A max.

AC Input: 24V

, 0.16A max.

Fa ult

V1+ V2+

PWR2PWR1

1 2 3 4 5 6

Figure 6: ISW-800T Top View

3.5 Wiring the Power Inputs

The 6-contact terminal block connector on the top panel of Industrial

Ethernet Switch is used for two DC redundant power inputs. Please

follow the steps below to insert the power wire by professionals.

Caution

When performing any of the procedures like inserting the

wires or tightening the wire-clamp screws, make sure the

power is OFF to prevent from getting an electric shock.

Caution

Lorsque vous effectuez l’une des procédures telles que

l’insertion des fils ou le serrage des vis de serrage,

assurez-vous que l’alimentation est coupée pour éviter tout

choc électrique.

- 5 - - 6 - - 7 -

3.6 Wiring the Fault Alarm Contact

The fault alarm contacts are in the middle of the terminal block

connector as the picture shows below. Inserting the wires, the Industrial

Ethernet Switch will detect the fault status of the power failure and then

forms an open circuit. The following illustration shows an application

example for wiring the fault alarm contacts.

1 2 3 4 5 6

Fault Alarm Contacts

The Fault Alarm Contacts are

energized (CLOSE) for normal

operation and will OPEN when

failure occurs

Fault

Insert the wires into the fault alarm contacts

Wire Range Wire Type Torque In-lbs (N.m)FW

12-24 AWG Str/Sol 5 (0.56)Cu 2

Alarm relay circuit accepts up to 24V DC, 1A.

3.7 Grounding the Device

Users MUST complete grounding wired with power cord adapter or

power supply source should be connected to a socket outlet with an

earthing connection; otherwise, a sudden lightning could cause fatal

damage to the device

Max. Fault Alarm Loading: 24V, 1A

DC Input: 12-48V

, 0.17A max.

AC Input: 24V

, 0.15A max.

Fault

V1+ V2+

PWR2PWR1

1 2 3 4 5 6

Note

EMD (Lightning) DAMAGE IS NOT CONVERED UNDER

WARRANTY.

Note

LES DOMMAGES EMD (éclair) NE SONT PAS PRIS SOUS

GARANTIE.

4. Installation

This section describes the functionalities of the Industrial Ethernet

Switch’s components and guides you to installing it on the DIN rail and

wall. Please read this chapter completely before continuing.

Note

This following pictures show the user how to install the

device, and the device is not ISW-500T or ISW-800T.

4.1 DIN-rail Mounting Installation

4.2 Wall-mount Plate Mounting

Mount on product or wall (Screw size and quantity: 4mm (L), 3mm

(dia.) and 4pcs); DIN-rail mount on product (Screw size and quantity:

4mm (L), 3mm (dia.) and 3pcs)

4.3 Side Wall-mount Plate Mounting

Caution

You must use the screws supplied with the wall-mounting

brackets. Damage caused to the parts by using incorrect

screws would invalidate your warranty.

Attention

Vous devez utiliser les vis fournies avec les supports

muraux. Les dommages causés aux pièces par l’utilisation

de vis incorrectes invalideraient votre garantie.

5. Customer Support

Thank you for purchasing PLANET products. You can browse our online

FAQ resource on PLANET web site rst to check if it could solve your

issue. If you need more support information, please contact PLANET

switch support team.

PLANET online FAQs:

http://www.planet.com.tw/en/support/faq.php

Support team mail address:

support @planet.com.tw

Contents are subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.

FCC Warning

This equipment has been tested and found to comply with the

regulations for a Class A digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in

a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used in

accordance with this user’s guide, may cause harmful interference to

radio communications. Operation of this equipment in a residential area

is likely to cause harmful interference, in which case the user will be

required to correct the interference at his own expense.

Avertissement de la FCC

Cet équipement a été testé et jugé conforme à la réglementation pour

un appareil numérique de classe A, conformément à la partie 15 des

règles de la FCC. Ces limites sont conçues pour fournir une protection

PLANET TECHNOLOGY CORPORATION

e-mail: sales@planet.com.tw http://www.planet.com.tw

10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2- - -2- -2219 9518 Fax:886 2219 9528

EC Declaration of Conformity

For the following equipment:

*Type of Product : Industrial 5- -/8 Port 10/100TX Compact Ethernet Switch

*Model Number : ISW-500T, -8ISW 00T

* Produced by:

Manufacturer‘s Name : Planet Technology Corp.

Manufacturer‘s Address : 10F., N Xindian Dist.,o.96, Minquan Rd.,

New Taipei City 231, Taiwan, R.O.C.

is herewith confirmed to comply with the requirements set out in the Council Directive on the

Approximation of the Laws of the Member States relating to Electromagnetic Compatibility

D 2014/30 Uirective on ( /E ).

For the evaluation regarding the EMC, the following standards were applied:

EN 55032 (2015 + AC:2016)

EN 55024 (2010 + A1:2015)

Responsible for marking this declaration if the:

Manufacturer Authorized representative established within the EU

Authorized representative established within the EU (if applicable):

Company Name: Planet Technology Corp.

Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan, R.O.C.

Person responsible for making this declaration

Name, Surname Kent Kang

Position / Title : Director

Taiwan

Apr. 12 18, 20

Place

Date

Legal Signature

raisonnable contre les interférences nuisibles lorsque l’équipement est

utilisé dans un environnement commercial. Cet équipement génère,

utilise et peut émettre de l’énergie radiofréquence et, s’il n’est pas

installé et utilisé conformément au présent guide de l’utilisateur,

peut causer des interférences nuisibles aux communications radio. Le

fonctionnement de ces équipements dans une zone résidentielle est

susceptible de provoquer des interférences préjudiciables, auquel cas

l’utilisateur sera tenu de corriger les interférences à ses propres frais.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may

cause radio interference, in which case the user may be required to take

adequate measures.

This equipment is compliant with Class A of CISPR 32. In a residential

environment this equipment may cause radio interference.

Avertissement de marquage CE

Il s’agit d’un produit de classe A. Dans un environnement domestique,

ce produit peut provoquer des interférences radio, auquel cas l’utilisateur

peut être tenu de prendre des mesures adéquates.

Cet équipement est conforme à la classe A du CISPR 32. Dans un

environnement résidentiel, cet équipement peut causer des interférences

radio.

WEEE Warning

To avoid the potential eects on the environment and human

health as a result of the presence of hazardous substances in

electrical and electronic equipment, end users of electrical and

electronic equipment should understand the meaning of the

crossed-out wheeled bin symbol. Do not dispose of WEEE as

unsorted municipal waste and have to collect such WEEE separately.

Avertissement WEEE

An d’éviter les eets potentiels sur l’environnement et la

santé humaine résultant de la présence de substances

dangereuses dans les équipements électriques et électroniques,

les utilisateurs naux d’équipements électriques et

électroniques devraient comprendre la signication du symbole

du bac à roulettes barré. Ne jetez pas les WEEE en tant que déchets

municipaux non triés et devez les collecter séparément.

Product specificaties

Merk:	Planet
Categorie:	Niet gecategoriseerd
Model:	ISW-800T
Kleur van het product:	Blauw
Gewicht:	300 g
Breedte:	70 mm
Diepte:	115 mm
Hoogte:	41 mm
Internationale veiligheidscode (IP):	IP30
LED-indicatoren:	Ja
Certificering:	FCC Part 15 Class A, CE
Netwerkstandaard:	IEEE 802.1p, IEEE 802.1x, IEEE 802.3, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x
Temperatuur bij opslag:	-40 - 85 °C
Vermogenstoevoer inclusief:	Nee
Ophangsysteem voor aan de muur:	Ja
Auto MDI/MDI-X:	Ja
Power over Ethernet (PoE):	Nee
Switchingcapaciteit:	1.6 Gbit/s
MAC-adrestabel:	1000 entries
10G support:	Nee
Datastroombeheer:	Ja
Switch type:	Unmanaged
Aantal basis-switching RJ-45 Ethernet-poorten:	8
Switch-laag:	L2
Type basis-switching RJ-45 Ethernet-poorten:	Fast Ethernet (10/100)
Throughput:	1.19 Mpps
Full duplex:	Ja
Koperen ethernetbekabelingstechnologie:	10BASE-T, 100BASE-TX
Wand montagekit:	Ja
Warmtedissipatie:	8.57 BTU/h
Buffergrootte:	448 KB
Stroomverbruik (typisch):	2.5 W
Bedrijfstemperatuur (T-T):	-40 - 75 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Code geharmoniseerd systeem (HS):	85176990
DIN rail bevestiging:	Ja
Store-and-forward:	Ja
Klemmenblok inclusief:	Ja
MAC-adres zelfverouderende functie:	Ja
MAC-adres zelflerende functie:	Ja
Klemmenblokpoort:	Ja
Authenticatie:	Poortgebaseerde authenticatie