Penton RCS6FT/EN Handleiding

Penton Speaker RCS6FT/EN

Lees hieronder de 📖 handleiding in het Nederlandse voor Penton RCS6FT/EN (1 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1

RoHS

Penton UK Ltd

Unit 2 Teville Industrials | Dominion Way | Worthing West Sussex | | BN14 8NW

T: +44 (0)1903 215315 F: +44(0)1903 215415 E: sales@pent onuk.co.uk | |

www.pentonuk.co.uk

1. LOUDSPEAKER

ENCLOSURE

2. REFERENCE AXIS

3. REFERENCE PLANE

4. HORIZONTAL PLANE

ROUND METAL CEILING

LOUDSPEAKERS

f RCS6FT/EN

f RCS6FT/ENC

INSTALLATION INSTRUCTIONS

EN54-24:2008

Certificate No: 0359-CPD-0120 TYPE A

Circuit Diagram

f RCS6FT/EN

f RCS6FT/ENC

* with capacitor

I IA

Slide

I ID

“C ”

“B”

1. Remove the wing nut “A” located on

the inside of the fire dome.

FITTING THE DOME INTO A CEILING

6. Cut a 200mm diameter hole paying attention to ensure that the cut-out is

accurately made. As if it is not, the speaker may not fit correctly into the ceiling

preventing the speaker from sitting flush to the surface.

7. Loosen the slider knob “D”, push the knob & plate upwards to the top of the fire

dome and re-tighten the knob to hold the slider in place. Repeat the same process

with the other slider.

8. Push the complete fire dome into the cut-out.

9. Once in place loosen the slider knob “D”, push the knob & plate downwards

until the slider makes firm contact with the ceiling. Tighten the knob to secure it into

place. Repeat the same process with the other slider.

10. The fire dome should be firmly

secured into the ceiling.

11. Take the speaker and

compress one of the mounting springs

& place both ends of the spring into

one of the retaining brackets located

on the inside wall of the fire dome.

Release the spring slowly into the

bracket. Once fully released the

spring will hold one side of the

speaker into the fire dome.

12. With the speaker in this position

connect the 3 wires hanging from the

termination plate on to the speaker using

the spade terminals provided.

13. Fit the second spring mount on

the speaker to the remaining bracket on

the inside of the fire dome. Finally push

the speaker into position.

14. If fitted correctly the speaker

should fit flush to the surface.

2. Lift the termination plate upwards

& away to separate it from the fire

dome “B”.

3. Gland the installation cable into the termination plate using

suitably rated 20mm glands. 2 gland entries are provided for

“loop in” “loop out” termination if required.

4. Terminate the installation cable into the terminal block on

the underside of the termination plate “C”.

5. Fix the termination plate back into the fire dome and secure

using the wing nut previously removed. Do not over tighten to

avoid damaging the thread.

EN54-24

ZCL0504-058/059

OCTOBER 2011

COMMON

1.5W

0.75W

0.25W

Product specificaties

Merk:	Penton
Categorie:	Speaker
Model:	RCS6FT/EN
Kleur van het product:	Wit
Gewicht:	1500 g
Breedte:	- mm
Diepte:	- mm
Hoogte:	120 mm
Materiaal behuizing:	Staal
Connectiviteitstechnologie:	Bedraad
Diameter:	239 mm
Gemiddeld vermogen:	6 W
Aanbevolen gebruik:	Universeel
Impedantie:	8 Ohm
Audio-uitgangskanalen:	- kanalen
Speaker plaatsing:	Plafond-montage
Aantal drivers:	1
Frequentiebereik:	180 - 18000 Hz
Versterker:	Nee
AC-ingangsspanning:	100 V
Bedrijfstemperatuur (T-T):	-10 - 55 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 95 procent
Transformatortrappen:	1.5, 3,6 W
Ingebouwde bijpassende transformator:	Ja