Peerless ECMU-01-I Handleiding

Peerless Flat panel steun ECMU-01-I

Lees hieronder de 📖 handleiding in het Nederlandse voor Peerless ECMU-01-I (31 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/31

Installation and Assembly:

Wind Rated I-beam Tilt Mount for 32" - 65" Outdoor Flat Panel

Displays

Models: ECMU-01-I, ECMU-01-I-S, ECMU-02-I, ECMU-02-I-S

ECMU-03-I, ECMU-03-I-S, ECMU-04-I, ECMU-04-I-S

Max Wind Rating: 90 mph, elevation 200 ft, Category D

ISSUED: 06-22-10 SHEET #: 061-9055-7 07-08-15

Max UL Load Capacity: 200 lb (90.7 kg)

2 of 36 ISSUED: 06-22-10 SHEET #: 061-9055-7 07-08-15

NOTE: Read entire instruction sheet before you start installation and assembly.

• Do not begin to install your Peerless product until you have read and understood the instructions and warnings

contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, for US

customers please call Peerless customer care at 1-800-865-2112, for all international customers, please contact

your local distributor.

• Due to outdoor environmental conditions such as strong wind gusts, heavy snow, hail, rain, etc. The environmental

enclosure, together with its mount, extension tube and hardware, must be inspected at least once a year, and

immediately following any time winds exceed 90 mph. A qualied installer or inspector must check for signs of rust,

loose fasteners, bent metal, etc. If evidence of excessive wear, deterioration or any unsafe condition is observed,

this product must be taken out of service immediately. Direct all inquiries to customer care if you have any

questions.

• This product should only be installed by someone of good mechanical aptitude, has experience with basic building

construction, and fully understands these instructions.

• Make sure that the supporting surface will safely support the combined load of the equipment and all attached

hardware and components.

• Never exceed the Maximum UL Load Capacity. See page one.

• If mounting to wood wall studs, make sure that mounting screws are anchored into the center of the studs. Use of

an "edge to edge" stud nder is highly recommended.

• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.

• Tighten screws rmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding

power.

• This product was designed for use with other outdoor products only.

WARNING

Tools Needed for Assembly

• phillips screwdriver, 5/32" allen wrench, 3/16" allen wrench

• level

Table of Contents

Parts List.................................................................................................................................................................................3

Installation to I-beam ..............................................................................................................................................................4

Installing Tilt Brackets .............................................................................................................................................................7

Mounting and Removing Flat Panel Screen ...........................................................................................................................8

3 of 36 ISSUED: 06-22-10 SHEET #: 061-9055-7 07-08-15

ECMU-01-I

ECMU-02-I

ECMU-03-I

ECMU-04-I

ECMU-01-I-S

ECMU-02-I-S

ECMU-03-I-S

ECMU-04-I-S

Description Qty. Part # Part # Model # Part #

ceiling plate 1 061-T1283 061-7283 ECMU-01-I 061-T1266

Bsupport column 1 see chart see chart ECMU-01-I-S 061-7266

Cceiling clamp 2 061-T1281 061-7281 ECMU-02-I 061-T1267

Dadapter box 1 061-T1264 061-7264 061-7267ECMU-02-I-S

E5/16"-18 x 1" socket screw 4 520-5035 520-5035 061-T1268ECMU-03-I

F7/16" x 4" hex head bolt 3 520-5014 520-5014 ECMU-03-I-S 061-7268

G7/16" nylock nut 3 530-5003 530-5003 ECMU-04-I 061-T1269

Hadapter plate 1 061-T1258 061-7258 061-7269ECMU-04-I-S

I1/4-20 x .75" socket screw 8 520-5034 520-5034

Jleft tilt bracket 1 061-T1383 061-7383

right tilt bracket 1 061-T1382 061-7382

Lsecurity allen wrench 1 560-9646 560-9646

MM6 x 12 mm socket pin screw 4 520-5023 520-5023

NM6 x 25 mm socket pin screw 4 520-5024 520-5024

OM8 x 15 mm socket pin screw 4 520-5026 520-5026

PM6 x 20 mm socket pin screw 4 520-5025 520-5025

QM8 x 25 mm socket pin screw 4 520-5027 520-5027

washer 4 540-5014 540-5014

S1/2-13 x 2" square head screw 4 520-5036 520-5036

T1/2-13 x 4" bolt 12 520-5019 520-5019

U1/2-13 nylock nut 8 530-5005 530-5005

1/2" washer 16 540-5010 540-5010

W5' wire rope (not shown) 1 560-0056 560-0056

Xcable clip 2 560-0069 560-0069

Y1/2-13 hex nut 4 530-5010 530-5010

Support Column (B)

Parts List

Parts may appear slightly different than illustrated.

Before you begin, make sure all parts shown are included with your product.

DFG

M N O

R S T

P Q

Product specificaties

Merk:	Peerless
Categorie:	Flat panel steun
Model:	ECMU-01-I
Kleur van het product:	Zwart
Gewicht:	29000 g
Breedte:	498 mm
Diepte:	381 mm
Hoogte:	781 mm
Gewicht verpakking:	32000 g
Montagewijze:	Plafond
Maximale gewichtscapaciteit:	90.7 kg
Montage interface compatibiliteit (min):	600 x 400 mm
Montage interface compatibiliteit (max):	600 x 400 mm
Aantal displays ondersteund:	1
Maximale schermgrootte:	65 "
Minimale schermgrootte:	32 "
Maximum afstand tot plafond:	382 mm