Park Tool RC-1 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Park Tool RC-1 (1 pagina's) in de categorie Fietsaccessoire. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
5115 Hadley Ave. N., St. Paul, MN 55128 (USA) www.parktool.com
PARK TOOL CO.
RC-1 Press Fit
Retaining Compound
Note:Park Tool AP-1 Adhesive
Primer must be used to prep all
components, fasteners and carbon
fiber surfaces prior to application of
Park Tool threadlockers or retaining
compound. Failure to do so could
result in permanently bonded parts.
Not recommended for titanium
threads.
Instructions:Clean and dry parts.
Twist off cap. Snip off tip. Apply prod-
uct to fastener and assemble. Fixture:
30 minutes. Full cure: 24 hours.
RC-1 Compo de
Rétention Press Fit
Note :Le Primaire Adhésif Park Tool
AP-1 doit être utilisé an de prépa-
rer tous composants, serrage ou sur-
face en fibre de carbone avant lappli-
cation du Frein Filet Park Tool ou autre
compo de rétention. Ne pas s’y tenir
pourrait sceller les pièces de façon
permanente. Non recommandé sur-
letages en titane.
Instructions :Nettoyer et sécher les
pièces. Dévisser le bouchon. Couper
la pointe. Appliquer le produit sur les
pièces et assembler. Fixation : 30 mi-
nutes. chage complet : 24 heures.
RC-1 Press Fit
Montagesicherung
Hinweis:Alle Komponenten und Ge-
winde, die mit Carbonfaser in Kontakt
kommen sowie Carbonfaser-Oberflä-
chen müssen vor der Verwendung von
Schrauben- oder Montagesicherung
mit AP-1 Oberflächengrundierung be-
handelt werden. Bei Nichtbeachtung
droht die permanente Verklebung der
betroffenen Teile. Nicht zu empfehlen
für Titan Gewinde.
Anleitung:Teile reinigen und trock-
nen. Verschluss aufdrehen. Spitze
abschneiden. Produkt auf Gewinde
auftragen und verschrauben. Handfes-
tigkeit: 30 min. Volle Wirksamkeit: 24 h.
RC-1 Sellador para
Piezas no Roscadas
Nota:El Preparador para Adhesión
AP-1 debe ser utilizado para preparar
todos los componentes, sujeciones y
superficies de fibra de carbón previo
a la aplicación de losjadores de ros-
cas. El no hacerlo, podría resultar en
piezas unidas de manera permanen-
te. No es recomendado para cuerdas
de titanio.
Instrucciones:Limpie y seque las par-
tes a tratar, retire la tapa, aplique el
producto y ensamble, el producto tar-
da 30 minutos para secar y 24 horas
para secar por completo.
RC-1 Instructions / Instructions / Anleitung / Instrucciones


Product specificaties

Merk: Park Tool
Categorie: Fietsaccessoire
Model: RC-1

Heb je hulp nodig?

Als je hulp nodig hebt met Park Tool RC-1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Fietsaccessoire Park Tool

Handleiding Fietsaccessoire

Nieuwste handleidingen voor Fietsaccessoire