Panduit RT2HT Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor Panduit RT2HT (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 134 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Website: www.panduit.com
E-mail: techsupport@panduit.com
For Technical Support:
888-506-5400, ext. 83255
RT2HT
MLT TENSIONING TOOL
© Panduit Corp. 2012
INTRODUCTION
The RT2HT Tool installs Panduit Pan-Steel coated and
uncoated MLTEH (Extra Heavy Cross Section), MLTEH15
(Extra Heavy Cross Section .015” Thick Body), and
MLTSH (Super Heavy Cross Section .015” and .025”
Thick Body) stainless steel ties.
Note: This tool is not intended for other uses such as
cutting or tensioning other types of fastening
devices.
TOOL FEATURES
A. Rear Handle
B.* Tension Pawl Release - Knob pointing towards the front
of tool for pawl engagement and to rear of tool for
disengagement.
C.* Anti-Backup Pawl Release - Lever up against tool for
pawl engagement and pulled down to disengage pawl.
D.* Detent Lock Pins - For controlled tension, pull both pins
forward; for manual tension, push both pins backward.
E. Cutter Handle - Cuts tie when tie is tensioned properly.
F. Cutter Blade
G. Tensioning Mandrel
H.* Tension Indicator Window - Located on the back of front
handle.
I.* Adjustment Knob - Adjust tension of tie application and
lock to desired tension with tension locking screw.
J. Tension Locking Screw
K. Front Handle - With ratchet controlled tensioning.
* See Page 2 for Feature Detail
E
D
C
A
B
FIGURE 1
TOOL OPERATION
1. Loop tie around bundle, thread tie into nose of tool and
through slot of tensioning mandrel.
2. Pull front handle to tension tie. Under controlled tension,
the front handle will break free when pre-determined
tension is attained.
3. Push cutter lever downward to cut tie.
4. Remove cut-off portion of tie from tool.
PA25757A01
Rev: 01 12-2012
I
J
H
G
F
FIGURE 2
K
RT2HT: PA25757A01_01 Page: 1 of 2 12-2012
PUSH BACKWARD
FOR MANUAL
TENSION
PULL FORWARD
FOR CONTROLLED
TENSION
D
B
C
TROUBLESHOOTING
TO RELEASE AND REMOVE TIE
FROM TOOL BEFORE CUTTING,
DISENGAGE BOTH KNOB AND
LEVER.
MULTI-POSITION HANDLE
ALLOWS ACCESS TO TIGHT AREAS.
A
TOOL MAINTENANCE
TO INHIBIT CORROSION AND MAINTAIN PERFORMANCE OF THE TOOL, KEEP THE METAL SURFACES COATED
WITH A LIGHT OIL (WD-40 ®OR EQUIVALENT).
6
4
2
7
5
3
1
-+
I
J
LOW
TENSION
HIGH
TENSION
ADJUSTMENT
KNOB
TENSION
INDICATOR
WINDOW
H
TENSION LOCKING
SET SCREW
TIE SIZE SETTING
1/2” (EH) TIE 1 – 2
1/2” (EH15) TIE 1 – 4
5/8” (SH) TIE 1 – 7
RT2HT MLT TENSIONING TOOL
RT2HT: PA25757A01_01 Page: 2 of 2 12-2012


Product specificaties

Merk: Panduit
Categorie: Niet gecategoriseerd
Model: RT2HT

Heb je hulp nodig?

Als je hulp nodig hebt met Panduit RT2HT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Panduit

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd