PAC RP4.2-TY11 Handleiding

PAC Niet gecategoriseerd RP4.2-TY11

Lees hieronder de đź“– handleiding in het Nederlandse voor PAC RP4.2-TY11 (7 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 13 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/7
Radio Replacement and
Steering Wheel Control Interface
for Toyota / Lexus / Scion Vehicles
RP4.2-TY11
© 2019 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 1
Rev: V6
Date:050319
Introduction and Features
Important Notes
The RP4.2-TY11 interface allows the replacement of a factory radio in select Toyota/Lexus/Scion vehicles and will retain
factory features such as steering wheel controls (SWC) and the factory audio ampliîšżer. This interface also allows you to
program two radio functions to each SWC button by using short press long press dual command functionality, and also
provides outputs such as: vehicle speed signal (VSS), illumination, reverse trigger and parking brake.
1. These instructions only apply to R.3.1.2.46 or later revisions. The revision info can be found on a small white sticker on the
interface and packaging.
2. Connection of the OBD connector, with the White / Red and White / Black wires, is not always necessary. Use of these wires
will be dependent on whether or not the aftermarket radio requires speciîšżc connections, and whether the vehicle provides these
outputs at the radio. See the “Installation Steps” section starting on page 3 for additional information.
3. Adjustment of the vehicle settings through the original radio’s vehicle settings menu will be disabled after installation of the new
radio. It is advised to make sure all settings are as you desire prior to removal of the original radio.
4. The RP4.2-TY11 does not retain Rear Seat Entertainment.
5. After installation, if you do not initially hear any audio, you may need to cycle the ignition again to initialize the factory ampliîšżer.
6. Speaker fading on factory amplied systems is only supported with the “amplied output” connection of the RP4.2-TY11.
7. When using real time fade, if the fader setting is biased more to the front or rear, as the radio turns on the sound may begin at
the default setting and then quickly transition to your custom setting.
8. Aftermarket radio features such as High Pass Filters (crossovers), DSP or “Network Mode” will interfere with proper fader
function. In order for the RP4.2-TY11’s fader function to work, the audio from the aftermarket radio’s output must match so it can
compare the front and rear audio levels and determine the proper fader setting for the factory ampliîšżer.
9. The USB-TY1 or USB-TY2 must be purchased in order to retain the factory USB port. Please refer to www.pac-audio.com to see
which harness you will need.
10. The CAM-TY11 or CAM-TY12 must be purchased in order to retain the factory reverse camera. Please refer to
www.pac-audio.com to see which harness you will need. If the required harness is not available, it is possible to hardwire the
reverse camera using the information provided in Appendix A on Page 7.
Module Layout
Module Status LED
USB Status LED
Interface Connector 1
Expansion Port
Interface Connector 2
Ampliîšżed Audio Output
Non-Ampliîšżed Audio Output
Programming Button
USB Port
Radio Select DIP switches
Interface Connector 4
Ampliîšżed Audio Output Level Adjustment
Radio Replacement and
Steering Wheel Control Interface
for Toyota / Lexus / Scion Vehicles
RP4.2-TY11
© 2019 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 2
Rev: V6
Date:050319
Interface Connectors
Plug Interface Connectors 1, 2 and 4 into the appropriate port on the RP4.2-TY11 interface (using the diagram on page 1 or
the label on the bottom of the RP4.2-TY11 interface). The Connector 3 connection will be dependent upon whether or not the
vehicle has a factory ampliîšżed system. Connect to the appropriate port on the RP4.2-TY11.
Vehicle Connectors
Depending on the application, the
RP4.2-TY11 will need 2 or 3 of the
5 vehicle connectors. The additional
connectors will be left unused on
the harness. Any additional radio
harnesses in the vehicle that do
not plug into one of the vehicle
connectors shown above, will not
be used. Below you will îšżnd the
combinations needed for most
vehicles.
Interface Connector 1 Interface Connector 2 Interface Connector 4
Interface Connector 3
Vehicle Connector 1 Vehicle Connector 2 Vehicle Connector 3 Vehicle Connector 4 Vehicle Connector 5
Combination 1
Typical 2004 to 2013 NON-AMPLIFIED
Vehicle Connector 3 Vehicle Connector 4 Vehicle Connector 5
Combination 2
Typical 2004 to 2013 AMPLIFIED
Vehicle Connector 1 Vehicle Connector 3
Combination 3
Typical 2014 to 2017 AMPLIFIED AND NON-AMPLIFIED
Vehicle Connector 2 Vehicle Connector 4 Vehicle Connector 5
Combination 4
Non-Typical 2012 to 2014 AMPLIFIED
Vehicle Connector 2
Vehicle Connector 1
*OBD-2 V3 *The OBD-2 V3 harness provides
CAN bus from the vehicle to the
RP4.2-TY11 for select vehicles
that do not already provide CAN
bus to the radio. Only use the
OBD-2 V3 if the aftermarket radio
requires connections for Vehicle
Speed Sense, Parking Brake, or
Reverse Signal for the following
applications:
1. Combination 1 from below.
2. Combination 2 from below.
Radio Replacement and
Steering Wheel Control Interface
for Toyota / Lexus / Scion Vehicles
RP4.2-TY11
© 2019 AAMP Global. All rights reserved. PAC is a Power Brand of AAMP Global.
PAC-audio.com
C
Page 3
Rev: V6
Date:050319
Installation Steps
Purple Rear R + input
Purple / Black Rear R - input
Green Rear L + input
Green / Black Rear L - input
Gray Front R + input
Gray / Black Front R - input
White Front L + input
White / Black Front L - input
Blue / Yellow SWC Output / Key 1
Brown SWC Output / Key 2
3.5 mm Jack SWC Output
Pink Vehicle Speed
Sense Output
Light Green Parking Brake
Output
Violet / White Reverse Signal
Output
Orange / White Illumination Output
Blue / White Amp Turn On Input
Blue Not Used
1. Set the Radio Select DIP switches according to the radio you are installing.
2. Wire the aftermarket radio harness per the tables to the right and the information below.
If the aftermarket radio does not require connections for Vehicle Speed Sense, Parking
Brake, or Reverse Signal, proceed to step “3”.
a. If the vehicle does not use the 28-pin connector (Vehicle Connector 2), proceed
to step “III” below. There are three different methods for obtaining the analog
navigation outputs from the interface:
I. Vehicles that have the analog signals at the radio: Plug the 28-pin
connector (Vehicle Connector 2) from the RP4.2-TY11 into the vehicle harness.
Find the Pink (pin 17), Light Green (pin 15) and Purple / White (pin 2) wires in
the RP4.2-TY11 harness and check for wires populating these positions on the
factory side of the connector. If the wires are present, you can use the analog
navigation outputs coming from Vehicle Connector 2 in the PAC harness.
II. Vehicles that have CAN data at the radio: Plug the 28-pin connector
(Vehicle Connector 2) from the RP4.2-TY11 into the vehicle harness. Find the
White / Red (pin 9) and White / Black (pin 10) wires in the RP4.2-TY11 harness
and check for wires populating these positions on the factory side of the connector.
If the wires are present, you can use the “nav wires” coming from Interface
Connector 4 in the PAC harness.
III. Vehicles that do not have the CAN data or the analog wires at the radio:
Insulate the Yellow and Black loose wires in the OBD-2 V3 connector (they
will not be used). Connect the OBD-2 V3 connector to the vehicle’s OBDII
connector (found under the dash on the driver’s side). Run the two wires from the
OBD-2 V3 from the OBDII connection, up to the radio cavity in the dash. Next,
unplug the 2-pin connector between Interface Connector 4 and Vehicle Connector
2. Connect the OBD-2 V3 2-pin connector into the 2-pin connector that comes
from Interface Connector 2. This will allow for use of the “nav wires” coming from
Interface Connector 4 in the PAC harness.
3. Wire your aftermarket radio to the RP4.2-TY11 harness according to the wiring connections
chart on this page.
White / Red HS CAN + Input
White / Black HS CAN - Input
Yellow +12v
Red Accessory Output
(10 amp)
Black Ground
Pink Vehicle Speed
Sense Output
Light Green
Parking Brake
Outpu
t
Violet / White Reverse Signal
Output
Aftermarket Radio Wiring Table
Wires from Interface Connector 4
Wires Labeled “Connect To
Aftermarket Radio”
OBD-2 V3 Wires
4. Once all connections have been made, plug the interface into the vehicle.
5. Turn the ignition on and set the gain on the side of the interface to the desired level. See
“Testing and Verication” section on page 6 for further details on how to set the gain.
. If you wish to reassign functions to the SWC, or utilize short press, long press dual
command functionality, follow the programming instructions starting on the following page.
Yellow Not Used
Black Not Used
Insulate the unused Yellow and
Black wires in the OBD-2 V3
Connector
Alpine JVC Kenwood /
Lightning Audio
Clarion /
Nakamichi
2-Wire
Resistive
Pioneer /
Other* Sony Fusion
1 2 1 & 2 3 2 & 3 1, 2, & 3 4 1 & 4
Set DIP switches that correspond with your radio to the ON position.
Set all other DIP switches to the OFF position.
*Other - Dual / Axxera (these brands could also have 2-wire resistive), Jensen, Rockford Fosgate
Wires Labeled
“OEM CAMERA POWER”
Yellow / Black +6v Camera Power
Black Camera Ground
OEM Camera Retention
6v Power and Ground
(see page 7 for more details)

Product specificaties

Merk: PAC
Categorie: Niet gecategoriseerd
Model: RP4.2-TY11

Heb je hulp nodig?

Als je hulp nodig hebt met PAC RP4.2-TY11 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd PAC

PAC

PAC LPHHD04 Handleiding

6 Maart 2024
PAC

PAC RP4.2-TY13 Handleiding

8 December 2023
PAC

PAC PGHGM2 Handleiding

7 Juli 2023
PAC

PAC CAM-TY12 Handleiding

6 Juli 2023
PAC

PAC VCI-NIS2 Handleiding

24 Juni 2023
PAC

PAC SNI-1/3.5 Handleiding

22 Juni 2023
PAC

PAC ANC-CH01 Handleiding

21 Juni 2023
PAC

PAC RP4-FD11 Handleiding

20 Juni 2023
PAC

PAC AP4-GM61 Handleiding

19 Juni 2023
PAC

PAC IGN-3 Handleiding

19 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive

Playtive IAN 327221 Handleiding

1 Mei 2024
Samsung

Samsung UN32J4001AF Handleiding

1 Mei 2024
Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024