PAC LCCH21 Handleiding

Bekijk gratis de handleiding van PAC LCCH21 (2 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 14 mensen en kreeg gemiddeld 4.6 sterren uit 3 reviews. Heb je een vraag over PAC LCCH21 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Pacic Accessory Corporation

®

| Ph. 866-931-8021 | [email protected]

©2015 Pacic Accessory Corporation

www.pac-audio.com

C

Rev. 092115

Page 1

Radio Replacement Interface

with Nav Outputs for

Chrysler / Dodge / Jeep Vehicles

With or Without Premium Audio Systems

LCCH11/LCCH21

1. Vehicles without a factory amplier: Connect the aftermarket radio’s front and

rear speaker wires to the 22 pin plug.

2. Vehicles with a factory amplier: Connect the front outputs of the

aftermarket radiorear inputs of the 22 pin radio connector to the . This will allow

navigation voice prompts and Bluetooth calls to be heard. The rear speaker outputs

of the aftermarket radio are not used. The factory amplier only accepts two audio

channels (left and right). The amplier’s fading is controlled by data communication

from the factory radio. The aftermarket radio does not have the ability to control the amplier’s fader.

3. The accessory output wire is located on the 11 pin CAN INTERFACE harness - connect this wire to the radio’s accessory

wire. The accessory wire supplies +12v, 1 amp max when key is in the accessory or ignition position (g. 1: If more current is

needed).

4. 11 pin plug (to CAN INTERFACE):

• Blue/White - Connect this wire to the radio’s amplifier remote output. Connect this wire with or without OEM amp

present! This connection is VERY IMPORTANT! Some of the LCCH11/

LCCH21 features will not function if this wire is not connetced!

• White/Green - SWC output.

• Green - Connect this wire to the radio’s reverse input wire only.

• Orange/White - Connect this wire to the radio’s Illumination input wire only.

• Violet/White - Connect this wire to the radio’s VSS input wire only.

• Red/White - Connect this wire to the radio’s parking brake input wire only.

Note: Do not connect these wires to any circuit other than the radio’s wire harness.

5. 11 pin plug (to SWC INTERFACE): This is a quick connection to a radio

specic SWC interface. No additional connections are necessary other than

radio control connections. Plug the radiospecic SWC interface in to this

connector and program the radio specic SWC interface for version 2. Do not

cut the loops. Refer to the SWC interface instruction manual for the radio specic control function programming order.

Fig. 1

(using a SPDT relay)

8586

30

87

87a

Ground

High Current 12v

(Fused)

12v Acc.

From

Interface

New High

Current Output

Diode 1N4005

or equivelant

23456

78

1011

Accessory Output

+12volts 1amp max.

Ch

91

23456

78

1011

91

SWC Interface.

Program for Version 2

Radio Specific Steering

Wheel Control Interface

(Sold Separately)

Program SWC

Interface for Version 2.

CAN INTERFACE

Navigation outputs and

Amplifier Remote Input

See Chart for wire color

descriptions.

Radio Connections. See aside

Chart for color description.

YellowBattery +12v

BlackGround

BlueAntenna On Input

WhiteFront L + input

White / BlackFront L - input

GreyFront R + input

Grey / BlackFront R - input

GreenRear L + input

Green / BlackRear L - input

PurpleRear R + input

Purple / BlackRear R - input

(Read the Installation Notes before making

connections to the provided radio harness)

CAN Interface Connection Chart:

RedAcc. Output (1 amp)

Red / WhiteP.B. Output (-)

Purple / WhiteVSS Output (Pulse)

Orange / WhiteIllum. Output (+)

GreenReverse Output (+)

White / GreenSWC Output

Blue / WhiteAmp Turn On Input

Installation Notes

Radio Connection Chart

Product specificaties