Ozito RTR-4100 Handleiding
Lees hieronder de đ handleiding in het Nederlandse voor Ozito RTR-4100 (8 pagina's) in de categorie Multitool. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/8
ROTARY
TOOL KIT
170W
INSTRUCTION MANUAL
SPECIFICATIONS
Voltage: 220-240V ~ 50Hz
Power: 170W
No Load Speed: 8,000 - 35,000/min
Collet Chuck Size: ø 1.5 - 3.2mm
Flexible Shaft Length: 1.0m
Tool Weight: 678g
RTR-4100
WHATâS IN THE BOX
Rotary Tool
Flexible Shaft
Rotary Bits x 189
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase and is intended for DIY (Do It
Yourself) use only. If a product is defective it will be replaced in
accordance with the terms of this warranty. Warranty excludes
consumable parts, for example: accessories, carbon brushes etc.
WARNING
The following actions will result in the warranty being void.
⢠If the tool has been operated on a supply voltage other
than that speciďŹed on the tool.
⢠If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
⢠Failure to perform maintenance as set out within the
instruction manual.
⢠If the tool is disassembled or tampered with in any way.
⢠Professional, industrial or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head OfďŹce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The beneďŹts provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ozito.com.au
1016
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
1 Collet Nut
2 Shaft Collar
3 Spindle Lock Button
4 Accessible Brushes
5 Variable Speed Dial
6 On/off Switch
7 Hanging Ring
8 Power Cord
ROTARY TOOL
KNOW YOUR PRODUCT
1. CHANGING ACCESSORIES
9 Flexible Shaft
10 Locking Chuck
11 Spindle Lock
12 Fitting Collar
13 Rotary Bits x 189
ACCESSORIES
SETUP & PREPARATION
1 2 3 4 5 6 7 8
9 10 12 1311
WARNING! ENSURE THE TOOL IS DISCONNECTED
FROM THE POWER SUPPLY BEFORE PERFORMING ANY
OF THE FOLLOWING OPERATIONS.
CAUTION! IT IS RECOMMENDED THAT NO ACCESSORY
LARGER THAN 55MM IN DIAMETER SHOULD BE FITTED
TO THE ROTARY TOOL.
1 Press and hold the spindle
lock button.
2 Unscrew the collet nut and
remove completely.
3 Select a suitable collet for
the accessory to be used
and insert. Then cover
with collet nut.
4 Lightly tighten the collet nut so
that it stays in place.
5 Insert shaft of accessory
into the collet.
6 Tighten collet nut using spindle
lock and spanner.
2. CHANGING ACCESSORIES CONT. 3. CHANGING ACCESSORIES CONT.
Locating a cutting/sanding disc Locating a sanding drum
2î îFitîtheîîżbreîîangeîeitherîsideî
of the cutting disc, then insert
the screw.
1 Loosen the screw on the top
of the sanding drum holder.
3 Tighten the cutting disc onto
the cutting disc holder.
2 Slide the sanding drum onto
the sanding drum holder.
1 Remove the screw from
the end of the disc holder.
Note: Do not over-tighten the screw as it could result in damage to the
cutting disc.
3 Tighten the screw until
the sanding drum sleeve
is secured.
Product specificaties
| Merk: | Ozito |
| Categorie: | Multitool |
| Model: | RTR-4100 |
Heb je hulp nodig?
Als je hulp nodig hebt met Ozito RTR-4100 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Multitool Ozito
14 Juni 2023
9 Juni 2023
6 Juni 2023
15 Mei 2023
3 Mei 2023
3 Mei 2023
21 April 2023
14 April 2023
2 Februari 2023
17 Januari 2023
Handleiding Multitool
- Multitool Bosch
- Multitool AEG
- Multitool DeWalt
- Multitool Bavaria
- Multitool Dremel
- Multitool Einhell
- Multitool Extech
- Multitool Fein
- Multitool Ferm
- Multitool Festool
- Multitool Gamma
- Multitool Gude
- Multitool Hama
- Multitool Hikoki
- Multitool Kress
- Multitool Makita
- Multitool Metabo
- Multitool Milwaukee
- Multitool Parkside
- Multitool Powerfix
- Multitool Powerplus
- Multitool Renovator
- Multitool Robust
- Multitool Rocktrail
- Multitool Ryobi
- Multitool Silvercrest
- Multitool Silverline
- Multitool Skil
- Multitool Stiga
- Multitool Taurus
- Multitool Toolcraft
- Multitool Topcraft
- Multitool Trotec
- Multitool Varo
- Multitool Vonroc
- Multitool Westfalia
- Multitool Worx
- Multitool Black And Decker
- Multitool Cocraft
- Multitool Meec Tools
- Multitool Cotech
- Multitool Fieldmann
- Multitool Lezyne
- Multitool Proxxon
- Multitool Porter-Cable
- Multitool EGO
- Multitool Leatherman
- Multitool Dedra
- Multitool Graphite
- Multitool RIDGID
- Multitool Craftsman
- Multitool G-Technology
- Multitool SKS
- Multitool Baumr-AG
- Multitool MTM
- Multitool Meister Craft
- Multitool McKenzie
- Multitool Ergotools Pattfield
- Multitool CMT Orange Tools
- Multitool Donau Elektronik
Nieuwste handleidingen voor Multitool
17 April 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024
10 April 2024
8 April 2024
19 Maart 2024
16 Maart 2024