Ozito PXHTWLS-4000 Handleiding

Ozito Verlichting PXHTWLS-4000

Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito PXHTWLS-4000 (6 pagina's) in de categorie Verlichting. Deze handleiding was nuttig voor 26 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6
STANDARD EQUIPMENT
PXHTWLS-4000
INSTRUCTION MANUAL
SPECIFICATIONS
Input: 18V DC or 220-240V AC
Power: 2 x 20W
Light Output: 2 x 2,000lumens
Colour Temperature: 5,000K
Ambient Temperature: 25°C (Max)
Rotation Range: 360° (in 2 axes)
Tripod Height: 850 - 1,780mm
Weight: 4.965kg
ozito.com.au
0419
2 x Hybrid Worklights
Mounting Bar, Cable Junction
& Tripod
3 x Fastening Knobs, 3 x
Washers & 2 x Wingnuts
HYBRID TWIN
LED WORKLIGHTS
& TRIPOD
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
OZITO Australia/New Zealand (Head Ofce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other than that specied
on the tool.
• If the tool shows signs of damage or defects caused by or resulting from
abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty and are excluded from the warranty extension. Warranty excludes
consumable parts.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
Attaching The Mounting Bar & Cables
1. Loosen the leg fastening knob on
the stem of the tripod by turning
it anti-clockwise.
2. Push down on the tripod leg ring
while maintaining a rm grasp
on the tripod stem to extend the
tripod legs.
3. Turn the leg fastening knob clockwise to lock the tripod legs in place.
4. Slide a fastening knob into the
bracket on the cable junction
unit, then through the central
hole on the mounting bar.
Note: The cable end with the
3-pin power plug (longest cable
length) should be pointing towards
the ground.
5. Slide a washer onto the end
of the fastening knob and then
screw this assembly into the
channel on the top of the tripod.
Installing The Worklights
1. Place a fastening knob through
the hole in the frame of a
worklight, then slide a washer
onto the fastening knob.
2. Insert the assembly through the
hole on one end of the mounting
bar and fasten from below with
one of the supplied wingnuts.
3. Repeat steps 1 & 2 with the other worklight.
1. AC Power Socket
2. Battery Seating
3. Dimming Control Knob
4. Worklight Frame
5. Rotation Adjustment Bolt
6. Frame Fastening Knob
7. Tripod Upper Section
8. Stem Fastening Knob
9. Tripod Stem
10. Leg Fastening Knob
11. Tripod Legs
12. Leg Support Bars
13. Cable Management Hook
14. AC Power Cord
15. Mounting Bar
16. LED Worklight
17. Mounting Bar Knob
This tool is compatible with all batteries & chargers from the Ozito Power X Change
range.
HYBRID TWIN LED WORKLIGHTS
& TRIPOD
BATTERY & CHARGER
KNOW YOUR PRODUCT
1. ASSEMBLY
SETUP & PREPARATION
16
17
1
13
2
6
8
10
9
5
11
12
7
3
15
14
4
Setting Up The Tripod Base
1. Loosen the leg fastening knob on the stem of the tripod by turning it
anti-clockwise.
2. Push down on the tripod leg ring
while maintaining a rm grasp
on the tripod stem to extend the
tripod legs.
3. Turn the leg fastening knob clockwise to lock the tripod legs in place.
Extending The Tripod Stem
1. Loosen the stem fastening knob
on the tripod stem by turning it
anti-clockwise.
2. Maintain a rm hold on the tripod
stem whilst pulling on the upper
section of the tripod to increase
the height of the tripod.
3. Turn the stem fastening knob clockwise to fasten to hold the extended
stem in place.
Note: The tripod leg support bars
can be inverted to increase the
extension height of the tripod even
with the legs widened to provide a
sturdier base. To do so, loosen the
leg fastening knob on the tripod
stem and pull on the stem while
holding on to the tripod legs.
Collapsing The Tripod
1. Loosen the stem fastening knob on the tripod and push down on the
upper part of the tripod stem to shorten the tripod. Retighten the stem
fastening knob once done to lock the stem height in place.
WARNING! MAINTAIN A FIRM HOLD ON THE TRIPOD
AS COLLAPSING THE LEGS CAN CAUSE THE UNIT
TO BECOME TOP HEAVY AND TOPPLE OVER.
2. Loosen the leg fastening knob on the tripod.
3. Maintain a rm hold on the tripod stem whilst pulling up on the tripod
leg ring. The tripod legs and the leg support bars should form a diamond
shape for the legs to collapse fully.
4. Retighten the leg fastening knob once done to lock the legs in place.
Turning The Worklights
1. Each worklight can also be
rotated individually by loosening
the fastening knob on the frame
of the worklight slightly, and
rotating the worklight to the
desired direction.
2. Retighten the fastening knob once adjustments are complete.
Rotating The Worklight
1. Loosen the bolts on the side of
the worklight frame slightly with
a hex key.
2. Rotate the worklight to the
desired angle.
Note: If the worklight does not remain at the set angle, tighten the bolts
on the side of the worklight frame slightly to hold it in place.
2. ADJUSTING THE TRIPOD 3. CHANGING LIGHTING DIRECTION
(1)
(2)
(1)
(2)

Product specificaties

Merk: Ozito
Categorie: Verlichting
Model: PXHTWLS-4000

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito PXHTWLS-4000 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Verlichting Ozito

Ozito

Ozito PXHTWLS-4000 Handleiding

20 Februari 2023

Handleiding Verlichting

Nieuwste handleidingen voor Verlichting

Aveo Engineering

Aveo Engineering Powerburst Daylite Handleiding

27 April 2024
Aveo Engineering

Aveo Engineering Redbaron XP Galactica Handleiding

27 April 2024
Aveo Engineering

Aveo Engineering Maxx Atlas Handleiding

27 April 2024
Aveo Engineering

Aveo Engineering Ultra Embedded Handleiding

27 April 2024
GVM

GVM -PRO-SD300C Handleiding

25 April 2024
GVM

GVM -PD60B Handleiding

25 April 2024
Lucide

Lucide Brackx-LED Handleiding

23 April 2024
Lucide

Lucide Dica LED Handleiding

23 April 2024
Lucide

Lucide Yazoo Led Handleiding

23 April 2024
Lucide

Lucide Dyvor-LED Handleiding

23 April 2024