Ozito MWR-9045 Handleiding
Ozito
Lasapparaat
MWR-9045
Lees hieronder de 📖 handleiding in het Nederlandse voor Ozito MWR-9045 (8 pagina's) in de categorie Lasapparaat. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/8
GASLESS
MIG WELDER
50 / 90 Amp
INSTRUCTION MANUAL
SPECIFICATIONS
Input Voltage: 240V ~ 50Hz
Welding Current: 50 / 90Amp
Welding Wire Size: 0.8, 0.9mm Flux-Cored Wire
Duty Cycle: 60%@50A, 10%@90A
Insulation Type: Class I
Max. Wire Spool Weight: 0.4kg
Weight (tool only): 14kg
MWR-9045
WHAT’S IN THE BOX
MIG Welder
Carrying Strap
Wire Feed Roller,
Shroud & Torch Tip
0.8mm Welding Wire
& Welding Mask
Chipping Hammer /
Wire Brush
ozito.com.au
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from
the original date of purchase. If a product is defective it will
be replaced in accordance with the terms of this warranty.
Warranty excludes consumable parts, for example: Welding tips,
torch nozzles, flexible inner tube, welding wire, wire feed rollers,
welding lenses, wire brushes and chipping hammer.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the
instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional or high frequency use.
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
1118
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
MIG WELDER
ACCESSORIES
1 Wire Feed Speed
2 Carry Handle
3 Overload Protection LED
4 On/OSwitch
5 Current Control Switch
6 Earth Clamp
7 MIG Torch
8 Torch Tip
9 Welding Mask
10 Chipping Hammer / Wire
Brush
11 Welding Wire (0.8mm)
12 Shroud (spare)
13 Torch Tip (spare)
14 Wire Feed Roller 0.8-0.9mm
(Fitted)
KNOW YOUR PRODUCT
1. WELDING MASK & CARRY STRAP
SETUP & PREPARATION
1 32 4 5
6 7 8
9 10 11 12 13 14
Fitting the Welding Screen
1 Insert the glass retaining pins
into the holes from the outside
ofthemaskandthentthe
retaining clips from the inside.
Rotate the clip to allow the
glass to be inserted.
3 Bend the sides and top of the
welding mask inwards and clip
together at the corners.
2 First insert the clear glass
into the recess of the welding
mask, followed by the dark
safety glass and then the
plastic frame.
Rotate the retaining clips to
lock in position.
4 Insert the 3 screws into the
handle mounting holes from
the outside. Fit the handle
onto the screws from inside
the mask and then secure
using the 3 nuts.
Theincludedweldingmaskmustbettedwiththeweldingscreenand
handle before using for welding.
TheMIGweldercanbettedwith0.8mmor0.9mmgaslesswelding
wire.Weldingwireupto0.4kgcanbettedtothiswelder.
2. FITTING THE WELDING WIRE COIL
4. WIRE DRIVE ROLLER SIZE
WARNING: ENSURE THE TOOL IS SWITCHED OFF AND
DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING STEPS.
2 Rotate the roller locking dial
anti-clockwiseandlifto.
4 Secure the wire drive roller
byttingtherollerlockingdial
and rotating it clockwise.
2 Remove the wing nut by
rotating anti-clockwise and
remove the drive washer.
4 Align the drive washer lug
with the slot in the drive shaft
and secure with the wing nut
by rotating clockwise.
There are two sizes on the roller included with the MIG welder; one side
oftherollersuits0.8mmgaslessux-coredweldingwireandtheother
suits0.9mmgaslessux-coredweldingwire.
1 Rotate the locking arm
up and then swing the
pressure arm away from
the guide roller.
3 Lift the wire drive roller
otheshaftandinspect
ittoconrmthewire
groove size stamped on
either face. Ensure the
wire drive roller size you
require is facing upwards
when assembled.
3 Slide the welding wire
coil onto the shaft.
Ensure the unwound
end of the welding
wire is on the closest
side to the wire guide.
1 Open the top cover
by rotating the locking
knob and then lifting
the panel.
a
b
a b
CAUTION: IT IS CRITICAL THAT YOU CHOOSE THE
CORRECT WIRE DRIVE ROLLER SIZE.
Product specificaties
| Merk: | Ozito |
| Categorie: | Lasapparaat |
| Model: | MWR-9045 |
Heb je hulp nodig?
Als je hulp nodig hebt met Ozito MWR-9045 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Lasapparaat Ozito
16 Maart 2024
30 Juni 2023
30 Juni 2023
18 Juni 2023
27 April 2023
22 Maart 2023
15 Oktober 2022
Handleiding Lasapparaat
- Lasapparaat Bavaria
- Lasapparaat Ferm
- Lasapparaat Gude
- Lasapparaat Gys
- Lasapparaat Holzmann
- Lasapparaat Hyundai
- Lasapparaat Kemppi
- Lasapparaat Kibani
- Lasapparaat Parkside
- Lasapparaat Powerplus
- Lasapparaat Scheppach
- Lasapparaat Silverline
- Lasapparaat Stanley
- Lasapparaat Taurus
- Lasapparaat Telwin
- Lasapparaat Topcraft
- Lasapparaat Weller
- Lasapparaat Workzone
- Lasapparaat Miller
- Lasapparaat Hilti
- Lasapparaat Herkules
- Lasapparaat SainSmart
- Lasapparaat Lincoln Electric
- Lasapparaat Hyper Welding
- Lasapparaat Mag-Torch
- Lasapparaat UNIMIG
- Lasapparaat Amico Power
- Lasapparaat THUN
- Lasapparaat Esab
Nieuwste handleidingen voor Lasapparaat
8 April 2024
8 April 2024
8 April 2024
8 April 2024
8 April 2024
8 April 2024
8 April 2024
8 April 2024
8 April 2024
8 April 2024