Ozito DMC-1000U Handleiding

Ozito Compressor DMC-1000U

Lees hieronder de đź“– handleiding in het Nederlandse voor Ozito DMC-1000U (3 pagina's) in de categorie Compressor. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
10. CLEANING & MAINTENANCE
B
AR
P
S
I
DIGITAL MINI
COMPRESSOR
12V
ORIGINAL INSTRUCTIONS
SPECIFICATIONS
Voltage: 12V
Max Current: 10Amp
Max Pressure: 100psi
Flow Rate: 16 l/min
Weight: 1kg
DMC-1000U
WHAT’S IN THE BOX
DESCRIPTION OF SYMBOLS
SPARE PARTS ozito-diy.co.uk
This appliance is not intended for use by young or inîšżrm persons unless
supervised by a responsible person to ensure that they can use the appliance
safely. Young children should be supervision to ensure that they do not play with
play with the appliance.
• When using the compressor, ensure you are parked in a safe, well lit location, off
the road and with the hand brake engaged.
• Ensure your personal safety is not at risk and never use the Digital Mini
Compressor while the car is in motion.
• Do not place the hose end against any part of your body when turned on, as this
may infuse air into your blood stream putting your health at serious risk.
• Do not make any alterations to this Compressor. Only use the adaptors supplied
with this product.
• Use this product only in accordance with operation instructions included in this
manual.
• If the vehicle fuse if blown, only replace with identical rated fuse.
• Inspect each part before use. Do not use if bent, broken, melted, burnt or if the unit
appears to be damaged.
• Check the tyre pressure before inating. Never exceed the suggested pressure of
the item being inated. If suggested pressure is exceeded, the item being inated
may burst.
• Do not bend or pinch the air hose while the Compressor is in use.
• It is not suggested that the Compressor work continuously for more than 10
minutes. If 10 minutes of use has been reached, turn it off and let it cool for 10
minutes before using again.
• If the Compressor is making abnormal sounds or its temperature if quite high, turn
off the power straight away and let it cool for at least 10 minutes before trying again.
Improper use may result in damage of the Compressor.
• Do not leave unattended and operating. Keep out of reach of children.
• Put the Compressor in a dry place if it is not in use for an extended period of time.
• Keep the Compressor away from ammable liquid or gas. Do not allow the
Compressor to become wet.
• Never put the connector and adaptors into your mouth, ear or eye. They are not
toys.
AIR COMPRESSOR SAFETY WARNINGS
WARNING! Read all safety warnings and all instructions. Failure to follow the
warnings and instructions may result in electric shock, îšżre and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the
warnings refers to your mains-operated (corded) power tool or battery-operated (cordless)
power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b.
Do not operate power tools in explosive atmospheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can cause
you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools. Unmodiîšżed plugs and
matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is earthed or
grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will
increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power
tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use a power tool while you are tired or under the inuence of drugs, alcohol
or medication.
A moment of inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection. Protective equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate
conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting
to power source and/or battery pack, picking up or carrying the tool. Carrying power
tools with your îšżnger on the switch or energising power tools that have the switch on invites
accidents.
d. Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better control
of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities,
ensure these are connected and properly used. Use of dust collection can reduce dust-
related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The correct
power tool will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from the power tool
before making any adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained
power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of the
power tool for operations different from those intended could result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualiîšżed repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
GENERAL POWER TOOL SAFETY WARNINGS-PERSONAL SAFETY
ELECTRICAL SAFETY
OPERATION
Cleaning
• Keep the ventilation vents of the Compressor clean at all times, if
possible, prevent foreign matter from entering the vents.
• After each use, blow air through the Compressor housing to ensure
it is free from all dust particles which may build up. Build up of dust
particles may cause the Compressor to overheat and fail.
• If the enclosure of the Compressor requires cleaning do not use
solvents but a moist soft cloth only. Never let any liquid get inside the
Compressor; never immerse any part of the Compressor into a liquid.
Note: Ozito Industries will not be responsible for any damage or
injuries caused by the repair of the Compressor by an unauthorised
person or by mishandling of the Compressor.
Digital Compressor
Accessories x 7
9. TROUBLESHOOTING 8. REPLACING FUSE
Problem Cause Solution
The compressor
does not start
Compressor not
connected to the power
Connect the 12V
socket to a 12V DC
outlet
Insufîšżcient supply
voltage
Try another 12V
outlet
Fuse needs replacing Replace Fuse
The compressor
starts but there is no
pressure
Loose hose
connections
Check the
compressed air
hose and adaptor
and replace if
necessary
The seals are damaged Check the seals
and have any
damaged seals
replaced by a
service centre
LED light wont turn
on
Compressor not
connected to the power
Plug the 12V socket
into a 12V outlet
High volume inating
does not completely
inate the item.
Not enough pressure
for high volume
ination
Inate using high
pressure air hose
not high volume
MAINTENANCE
WARNING! When using mains-powered tools, basic safety precautions, including the
following, should always be followed to reduce risk of îšżre, electric shock, personal injury
and material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before
operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
Before you connect the equipment to the power supply make sure that the data on the rating plate are
identical to the mains data.
If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid
a hazard.
1 Unscrew the top of the 12V socket to expose the fuse.
The 12V socket is îšżtted with a 10A fuse to protect the air compressor. If
the compressor has stopped working and no lights or LEDs illuminate,
the fuse may need to be replaced.
2 Replace the 10A fuse and screw the top back onto the 12V socket.
WARNING: ENSURE THE TOOL IS SWITCHED OFF AND
DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING STEPS.
WARNING: BEFORE CLEANING YOUR COMPRESSOR
OR CARRYING OUT ANY MAINTENANCE PROCEDURE,
ENSURE THE COMPRESSOR IS SWITCHED OFF AND
DISCONNECTED FROM THE POWER SUPPLY.
IMPORTANT: STORE THE COMPRESSOR ONLY IN A DRY
LOCATION WHICH IS NOT ACCESSIBLE TO UNAUTHORISED
PERSONS. ALWAYS STORE UPRIGHT, NEVER TILTED!
WARNING: WAIT UNTIL THE COMPRESSOR HAS
COMPLETELY COOLED DOWN TO PREVENT BURNS.
B
A
R
P
S
I
WARRANTY
OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG 0716
All of our products undergo strict quality checks to ensure that they reach
you in perfect condition. In the unlikely event that your device develops a
fault, please contact our service department at the address shown on this
guarantee card. You can also contact us by telephone using the customer
service number shown. Please note the following terms under which
guarantee claims can be made:
1. These warranty terms regulate additional warranty services, which the
manufacturer mentioned below promises to buyers of its new products
in addition to their statutory guarantee claims are not affected by this
guarantee. Our guarantee is free of charge to you.
2. The warranty services only covers defects due to material or
manufacturing faults on a product which you have bought from the
manufacturer mentioned below are limited to either the rectiîšżcation of said
defects on the product or the replacement of the product, whichever we
prefer.
Please note that our devices are not designed for use in commercial, trade
or professional applications. A guarantee contract will not be created if the
device has been used by commercial, trade or industrial business or has
been exposed to similar stresses during the guarantee period.
3. The following are not covered by our guarantee:
- Damage to the device caused by a failure to follow the assembly
instructions or due to incorrect installation, a failure to follow the operating
instructions (for example connecting it to an incorrect mains voltage or
current type) or a failure to follow the maintenance and safety instructions
or by exposing the device to abnormal environmental conditions or by lack
of care and maintenance.
- Damage to the device caused by abuse or incorrect use (for example
overloading the device or the use or unapproved tools or accessories),
ingress of foreign bodies into the device (such as sand, stones or dust,
transport damage), the use of force or damage caused by external forces
(for example by dropping it).
- Damage to the device or parts of the device caused by normal or natural
wear or tear or by normal use of the device.
4. Your Product is guaranteed for a period of 36 months from the original
date of purchase and is intended for DIY (Do It Yourself) use only. Lithium
Ion batteries and chargers are covered by a 12 month warranty. Warranty
excludes consumable parts. Guarantee claims should be submitted
before the end of the guarantee period within two weeks of the defect
being noticed. No guarantee claims will be accepted after the end of the
guarantee period. The original guarantee period remains applicable to the
device even if repairs are carried out or parts are replaced. In such cases,
the work performed or parts îšżtted will not result in an extension of the
guarantee period, and no new guarantee will become active for the work
performed or parts îšżtted. This also applies if an on-site service is used.
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST
RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR
REGISTER RECEIPT.
Please refer to the restrictions of this warranty concerning wearing parts,
consumables and missing parts as set out in the service information in
these operating instructions.
CUSTOMER SERVICE HELPLINE
GB: 0151 294 4488
IRL: 1850 882711
Ozito-diy.co.uk
Warning
Read instruction manual
VVolts Watts W
dc Direct current mA Milliamperes
Indoor use only
Spare parts can be ordered from the Special Orders Desk
at your local Bunnings Warehouse or Homebase store.
For further information, or any parts visit
www.ozito-diy.co.uk or contact Ozito Customer Service:
Great Britain: 0151 294 4488
Ireland: 1850 882711
E-mail: enquires@ozito-diy.co.uk
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
3. CONTROLS
Light Button
PSI / BAR Button
1 To turn the LED light on, press
the light button in.
1 To switch between the two
pressure units, press the PSI /
BAR button.
2 To turn the LED light off, press
the light button again.
Note: The compressor must be connected to the power for the LED
light to work.
The compressor has a built-in LED light for ease of use at night or in a
dark area.
The digital pressure reading can be switch between PSI and BAR to
match the requirements on the item being inated.
To identify the current pressure units, a light will be illuminated on the
right side of the digital display.
BA
R
P
S
I
B
A
R
P
S
I
B
A
R
P
S
I
2. SWITCHING ON & OFF
Connecting to a 12V outlet
Switching On and Off
1 Roll out the 12V socket from
the base of the unit.
1 To start the air compressor
press down the on/off button
with your foot.
The compressor is îšżtted with a foot peddel on/off button to allow ease
of use while holding adaptors and the item being inated.
2 Connect the 12V
socket to 12V DC
outlet which can be
found in your vehicle.
Check car outlet for
sufîšżcent power up to
120W.
2 Release the on/off
button to stop the
compressor.
BA
R
P
S
I
WARNING:COMPRESSED AIR CAN BE DANGEROUS.
NEVER POINT THE OUTLET NOZZLE TOWARDS ANY
PART OF YOUR BODY OR ANOTHER PERSON.
B
A
P
S
I
7. HIGH VOLUME APPLICATION
1 LED Light
2 Light Button
3 PSI / BAR Button
4 Digital Pressure Gauge
5 Carry Handle
6 On/Off Button
7 Side Compartment
8 Air Hose
9 12V Socket
10 High Volume Hose
11 Adaptor Storage
12 High Volume Air Outlet
FRONT VIEW
BACK / BASE VIEW
ACCESSORIES
KNOW YOUR PRODUCT
DMC-1000U
1. ADAPTORS 5. INFLATING TYRES 4. INFLATING 6. INFLATING SPORTING EQUIPMENT
SETUP & PREPARATION OPERATION
13 High Pressure Adaptor
14 Medium Adaptor
15 Large Adaptor
16 General Purpose Adaptors
17 Ball Adaptor
Removing Adaptors
Side Compartment
Base Compartment
1 Open the side
compartment and roll
out the air hose.
3 Attach the air hose
by screwing the
end of the hose in a
clockwise direction.
5 Uncrew the air hose
and tighten plastic
cap onto the tyre air
valve.
5 Remove the adaptor
from the inated
item.
5 Remove the adaptor
from the inated
item.
1 Open the side
compartment and roll
out the air hose.
1 Remove the high
volume hose from
the base of the
compressor and
insert into the high
volume air outlet.
The air compressor is deisgned for quick and easy ination of high air
volume objects such as air matresses, rafts and pool toys.
2 Connect the 12V
socket to a power
supply. The current
pressure rating of the
item you are inating
will now appear on
the digital display.
3 Insert the connected
adaptor into the
inatable item.
3 Insert the connected
adaptor into the
inatable item.
4 Once the pressure
has reached the
desired rating,
remove the air hose
and roll up into the
side compartment.
1 To open the side compartment,
slide the door up. Lower the
door to expose the adaptors.
1 Turn the unit over so you can
see the base.
2 Remove the
required adaptor.
2 The 3 adaptors and
air hose can now be
removed.
3 To close the side compartment
raise the door and slide down
to secure.
The compressor unit has 7 adaptors to allow a range of functions. All
the adaptors are secured in either the compartment on the side or
base.
3 Press down the on/off switch
to inate the tyre to the
recomended pressure is
reached.
NOTE: The required pressure
should be written on the item.
1 Attach the required adator for
the job.
NOTE: See the following
pages to select the correct
adaptors. 2 Unscrew the cap on the tyre air
valve.
4 Follow steps 2 - 3 in section 3.
“Inating” to inate the tyre. 4 Follow steps 2 - 3 in section 3.
“Inating” to inate the item.
4 Follow steps 2 - 3 in section 3.
“Inating” to inate the item.
6 Place the adaptors and air
hose back into thier original
compartments. Disconnect the
12V socket.
6 Place the adaptors and air
hose back into thier original
compartments. Disconnect the
12V socket.
NOTE: The same proccess can be used to inate balloons using the
general purpose adaptors instead of the ball adaptor.
6 Place the adaptors and air
hose back into thier original
compartments. Disconnect the
12V socket.
2 Remove the ball adaptor from
the base of the compressor
and screw onto the end of the
air hose. 2 Attach the desired size adaptor
from the side compartment.
WARNING: ENSURE THE TOOL IS SWITCHED OFF AND
DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING STEPS.
IMPORTANT: BEFORE CONNECTING OR DISCONNECTING
ACCESSORIES, ALWAYS MAKE SURE THAT THE
COMPRESSOR IS OFF.
WARNING: AVOID INFLATING THE OBJECTS ABOVE
THE RECOMMENDED INFLATION PRESSURE. THIS MAY
LEAD TO DAMAGE AND/OR INJURIES.
1 2 3 4 5
6 7
8 9 10
11
12
13
14
15
16
17

Product specificaties

Merk: Ozito
Categorie: Compressor
Model: DMC-1000U

Heb je hulp nodig?

Als je hulp nodig hebt met Ozito DMC-1000U stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Compressor Ozito

Ozito

Ozito PXOFCS-636 Handleiding

8 April 2024
Ozito

Ozito ACK-0015 Handleiding

16 Maart 2024
Ozito

Ozito ACP-2415 Handleiding

16 Maart 2024
Ozito

Ozito PXHDIS-240U Handleiding

29 Augustus 2023
Ozito

Ozito AMC-3000U Handleiding

28 Mei 2023
Ozito

Ozito ACP-24151U Handleiding

22 Mei 2023
Ozito

Ozito DMC-1000U Handleiding

20 Mei 2023
Ozito

Ozito ACK-190U Handleiding

18 Mei 2023
Ozito

Ozito SAC-2110 Handleiding

16 Mei 2023
Ozito

Ozito MACP-015 Handleiding

29 Maart 2023

Handleiding Compressor

Nieuwste handleidingen voor Compressor

Unimac

Unimac ACM-200s Handleiding

9 April 2024
Unimac

Unimac ACM-150s Handleiding

9 April 2024
Unimac

Unimac ACM-160s Handleiding

9 April 2024
Merlin

Merlin Vago Handleiding

3 April 2024
Holzmann

Holzmann LSR 10HQ Handleiding

27 Maart 2024
Aerotec

Aerotec 25/GR 80 Handleiding

27 Maart 2024
Hazet

Hazet 9037 SPC Handleiding

25 Maart 2024
Herkules

Herkules AIRTECH 2500/1 Handleiding

16 Maart 2024
Global

Global GK 210/24 Handleiding

16 Maart 2024
OKAY

OKAY EURO 2200/1 Handleiding

16 Maart 2024