Orion TV1929 Handleiding

Orion Televisie TV1929

Lees hieronder de 📖 handleiding in het Nederlandse voor Orion TV1929 (8 pagina's) in de categorie Televisie. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8

Converter/Descrambler

Splitter A/B Switch

Converter/Descrambler

VHF Antenna

Incoming CATV

Combination VHF/UHF Antenna (Single 75 ohm

cable or 300 ohm twin-lead wire)

Connect the 75 ohm cable from a combination VHF/UHF

antenna to the antenna jack.

If your combination antenna has a 300 ohm twin-lead wire,

use the 300-75 ohm matching transformer (not supplied).

Combination VHF/UHF Antenna (Separate VHF

and UHF 300 ohm twin-leads)

Connect the UHF twin-lead wire to a combiner (not supplied).

Connect the VHF twin-lead to the 300-75 ohm matching

transformer (not supplied). Attach the transformer to the

combiner. Attach the combiner to the antenna jack.

Separate VHF/UHF Antennas

Connect the 75 ohm cable from the VHF antenna and the

UHF antenna twin-lead to a combiner (not supplied). Attach

the combiner to the antenna jack.

NOTE:If your VHF antenna has a twin-lead wire, use the

300-75 ohm matching transformer (not supplied), then

connect the transformer to the combiner.

For Subscribers to Basic Cable TV Service

For basic cable service not requiring a converter/

descrambler box, connect the CATV 75 ohm coaxial cable

directly to the antenna jack on the back of the television.

For Subscribers to Scrambled Cable TV Service

If you subscribe to a cable service which requires the use of

a converter/descrambler box, connect the incoming cable to

the converter/descrambler box and connect the output of

the box to the antenna jack on the back of the television.

Follow the connections shown left. Set the television to the

output of the converter/descrambler box (usually channel 3 or

4) and use the converter/descrambler box to select

channels.

For Subscribers to Unscrambled Basic Cable

with Scrambled Premium Channels

If you subscribe to a cable service in which basic cable

channels are unscrambled and premium channels require

the use of a converter/descrambler box, you may wish to

use a two-set signal splitter (sometimes called a "two-set

coupler") and an A/B switch box from the cable installer or

an electronics supply store. Follow the connections shown

left. With the switch in the "B" position, you can directly tune

any nonscrambled channels on your TV. With the switch in

the "A" position, tune your TV to the output of the converter/

descrambler box (usually channel 3 or 4) and use the box to

tune scrambled channels.

Indoor Antenna

A single pole antenna is supplied

with the unit (TV1329 only),

insert the antenna holder into

the mounting hole on the back

of the cabinet until it locks into

place. Attach the antenna plug

to the antenna jack. Adjust the

length and angle of the

antenna rod to receive the best

possible picture.

This television has an extended tuning range and

can tune most cable channels without using a cable

company supplied converter box. Some cable

companies oﬀer "premium pay channels" in which

the signal is scrambled. Descrambling these signals

for normal viewing requires the use of a descrambler

device which is generally provided by the cable

company.

ANTENNA/CATV CONNECTIONS

ANT

Single 75 ohm cable

Combination VHF/UHF Antenna

300 ohm twin-lead wire

Splitter

Take oﬀ the Splitter 300-75 ohm Matching

Transformer

(not supplied)

Single 75 ohm cable

300 ohm twin-lead wire

UHF Antenna

Combiner

(not supplied)

300-75 ohm Matching

Transformer

(not supplied)

TV/CATV MODE SELECTION

When shipped from the factory, the TV/CATV menu option is set to the "CATV"

(Cable Television) mode. If not using CATV, set this menu option to "TV " mode.

ATTENTION

If you purchase a universal remote control from your local retailer, please contact

the remote manufacturer for the required programming code.

CAUTION

Changes or modiﬁcations not expressly approved by the party responsible for

compliance with the FCC Rules could void the user's authority to operate this

equipment.

Quartz PLL Frequency Synthesized Tuning System - Electronically locks in and

memorizes available channels for perfect reception.

181 Channel Tuner - The tuning system is capable of receiving all 68 VHF/UHF

standard broadcast channels that are available in your area. When operating on a cable

system, it can tune to the standard VHF channel frequencies plus up to 113 cable

channel frequencies. The actual number of channels received depends upon channel

reception in your area or your cable system.

On-Screen 3 Language Display - Consists of channel, sleep timer, volume level,

muting, text/caption indicators and picture control adjustments. These can be displayed

in English, Spanish or French.

Picture Adjustments Using The Remote Control - The On-Screen display allows

precise remote control adjustment of BRIGHTNESS, COLOR, CONTRAST,

SHARPNESS and TINT.

Sleep Timer - Operable from the remote control, this TV can be programmed up to 120

minutes to turn oﬀ automatically.

Memory Back Up - This system prevents loss of memorized channel selections in case

a power interruption to the TV should occur.

V-Chip - The V-Chip function can rate a TV program or movie content. It allows you to

set a restriction level.

Closed Captioned Decoder - Displays text captions or 1/3 of full screen text on the

screen for hearing impaired viewers.

FEATURES

Printed in Thailand

ENGLISH

OWNER'S

MANUAL

COLOR TELEVISION

ORION warrants this product to be free from manufacturing defects in material and workmanship under

normal use and conditions for a period of twelve (12) months from date of original purchase in the United

States only.

Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction

during the ﬁrst twelve (12) months from date of original purchase, ORION will provide carry-in repair

service at an ORION authorized Independent Service Center at no charge. Also, if an original part fails due

to manufacturing defect in material and workmanship within one year from date of original purchase (two

years from date of original purchase for picture tube) we will replace the defective part only (LABOR NOT

INCLUDED AFTER THE INITIAL ONE YEAR WARRANTY PERIOD) provided the defect or malfunction is

veriﬁed along with dated proof of purchase.

There are Independent Service Centers located throughout the country. For the one nearest you, DIAL

TOLL FREE: 1-800-289-0980.

In the event there is no such local Independent Service Center, the product may be returned to the ORION

Factory Service Center* listed below.

• Pack the unit in a well-padded heavy corrugated box.

• Enclose your check or money order payable to ORION in the amount of $19.00 to cover shipping and

handling costs.

• Enclose proof of purchase (warranty service will not be performed without dated proof of purchase).

• Ship the unit prepaid via UPS or parcel post (insured).

Note: This warranty is void if the product is:

(a) Damaged through negligence, misuse, abuse, or accident.

(b) Used in a commercial application or rentals.

eﬀect warranty repairs to the class of product or by the ORION Factory Service Center.

(d) Damaged because it is improperly connected to the equipment of other manufacturers.

This warranty does not cover:

(a) Damage to equipment not properly connected to the product.

(b) Costs incurred in the shipping of the product to an authorized Independent Service Center or ORION

Factory Service Center.

follow operating instructions provided with the product.

(d) Ordinary adjustments to the product which can be performed by customer as outlined in the owner's

manual.

(e) Signal reception problems caused by external antenna or cable systems.

THIS WARRANTY IS NON-TRANSFERABLE AND APPLIES ONLY TO THE ORIGINAL PURCHASER

AND DOES NOT EXTEND TO SUBSEQUENT OWNERS OF THE PRODUCT. ANY APPLICABLE

IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED IN

DURATION TO A PERIOD OF THE EXPRESS WARRANTY AS PROVIDED HEREIN BEGINNING WITH

THE DATE OF ORIGINAL PURCHASE AT RETAIL AND NO WARRANTIES, WHETHER EXPRESS OR

IMPLIED SHALL APPLY TO THIS PRODUCT THEREAFTER. ORION MAKES NO WARRANTY AS TO

THE FITNESS OF THE PRODUCT FOR ANY PARTICULAR PURPOSE AND USE.

UNDER NO CIRCUMSTANCES SHALL ORION BE LIABLE FOR ANY LOSS, DIRECT, INDIRECT,

INCIDENTAL, SPECIAL, OR CONSEQUENTIAL DAMAGE ARISING OUT OF OR IN CONNECTION

WITH THE USE OF THIS PRODUCT.

THIS WARRANTY IS VALID ONLY IN THE UNITED STATES OF AMERICA. THIS WARRANTY GIVES

YOU SPECIFIC LEGAL RIGHTS, HOWEVER, YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY

FROM STATE TO STATE. SOME STATES DO NOT ALLOW LIMITATION ON IMPLIED WARRANTIES

OR EXCLUSION OF CONSEQUENTIAL DAMAGE, THEREFORE, THESE RESTRICTIONS MAY NOT

APPLY TO YOU.

*ORION SALES, INC.

HIGHWAY 41

ORION PLACE

PRINCETON, INDIANA 47670

LIMITED WARRANTY

TV1329

TV1929

3H40101D K

99/09

3H40101D E 28.09.99, 10:222

1 2 3 4

5 6 7 8

POWER

QUICK

VIEW CALL

SLEEP

RESET

CAPTION/TEXT

CH.1/2

SET ENTER

MUTING

VOL CH

Wider Hole

and Blade

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR

MOISTURE.

IMPORTANT SAFEGUARDS

CAUTION:TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER

(OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING

TO QUALIFIED SERVICE PERSONNEL.

d. If the unit does not operate normally by

following the operating instructions.

Adjust only those controls that are

covered by the operating in structions, as

an improper adjustment of other controls

may result in damage and will often

require extensive work by a qualiﬁed

technician to restore the unit to its normal

operation.

e. If the unit has been dropped or the

cabinet has been damaged.

f. When the unit exhibits a distinct change

in performance, this indicates a need for

service.

REPLACEMENT PARTS- When replace-

ment parts are required, be sure the service

technician uses replacement parts specified

by the manufacturer or those that have the

same characteristics as the original part.

Unauthorized substitutions may result in fire,

electric shock or other hazards.

SAFETY CHECK- Upon completion of any

service or repairs to this unit, ask the service

technician to perform safety checks to

determine that the unit is in proper operating

condition.

WALL OR CEILING MOUNTING- The

product should be mounted to a wall or

ceiling only as recommended by the

manufacturer.

HEAT- The product should be situated away

from heat sources such as radiators, heat

registers, stoves, or other products

(including ampliﬁers) that produce heat.

NOTE TO CATV SYSTEM INSTALLER

This reminder is provided to call the CATV

system installer's attention to Article 820-40

of the NEC that provides guidelines for proper

grounding and, in particular, speciﬁes that

the cable ground shall be connected to the

grounding system of the building, as close to

the point of cable entry as practical.

POWER-CORD PROTECTION- Power-supply

cords should be routed so that they are not

likely to be walked on or pinched by items

placed upon or against them, paying particular

attention to cords at plugs, convenience

receptacles, and the point where they exit from

the appliance.

LIGHTNING- To protect your unit during a

lightning storm, or when it is left unattended

and unused for long periods of time, unplug it

from the wall outlet and disconnect the

antenna or cable system. This will prevent

damage to the unit due to lightning and power

line surges.

POWER LINES- An outside antenna system

should not be located in the vicinity of

overhead power lines, or other electric light or

power circuits, or where it can fall into such

power lines or circuits. When installing an

outside antenna system, extreme care should

be taken to keep from touching such power

lines or circuits as contact with them might be

fatal.

OVERLOADING- Do not overload wall outlets

and extension cords as this can result in a risk

of ﬁre or electric shock.

OBJECT AND LIQUID ENTRY- Do not push

objects through any openings in this unit as

they may touch dangerous voltage points or

short out parts that could result in ﬁre or

electric shock. Never spill or spray any type of

liquid into the unit.

OUTDOOR ANTENNA GROUNDING- If an

outside antenna or cable system is connected

to the unit, be sure the antenna or cable

system is grounded so as to provide some

protection against voltage surges and built-up

static charges. Section 810 of the National

Electrical Code, ANSI/NFPA 70, provides

information with respect to proper grounding of

the mast and supporting structure, grounding

of the lead-in wire to an antenna discharge

unit, size of grounding conductors, location of

antenna discharge unit, connection to

grounding electrodes, and requirements for the

grounding electrode.

SERVICING- Do not attempt to service this

unit yourself as opening or removing covers

may expose you to dangerous voltage or other

hazards. Refer all servicing to qualiﬁed service

personnel.

DAMAGE REQUIRING SERVICE- Unplug this

unit from the wall outlet and refer servicing to

qualiﬁed service personnel under the following

conditions:

a. When the power-supply cord or plug is

damaged.

b. If liquid has been spilled, or objects have

fallen into the unit.

c. If the unit has been exposed to rain or water.

12.

13.

14.

15.

16.

17.

18.

19.

The lightning ﬂash with arrowhead symbol, within

an equilateral triangle is intended to alert the user

to the presence of uninsulated dangerous voltage

within the product's enclosure that may be of

suﬃcient magnitude to constitute a risk of electric

shock to persons.

An appliance and cart combination should be

moved with care. Quick stops, excessive

force, and uneven surfaces may cause the

appliance and cart combination to overturn.

VENTILATION- Slots and openings in the

cabinet and in the back or bottom are provided

for ventilation, to ensure reliable operation of

the unit and to protect it from overheating.

These openings must not be blocked or covered.

The openings should never be blocked by

placing the unit on a bed, sofa, rug, or other

similar surface. This unit should never be

placed near or over a radiator or heat source.

This unit should not be placed in a built-in

installation, such as a bookcase, or rack

unless proper ventilation is provided or the

manufacturer's instructions have been

adhered to.

POWER SOURCE- This unit should be

operated only from the type of power source

indicated on the rating plate. If you are not

sure of the type of power supply to your home,

consult your appliance dealer or local power

company. For units intended to operate from

battery power, or other sources, refer to the

operating instructions.

GROUNDING OR POLARIZATION- This unit

is equipped with a polarized alternating

current line plug (a plug having one blade

wider than the other). This plug will ﬁt into the

power outlet only one way. This is a safety

feature. If you are unable to insert the plug

fully into the outlet, try reversing the plug. If the

plug should still fail to fit, contact your

electrician to replace your obsolete outlet. Do

not defeat the safety purpose of the polarized

plug. If your unit is equipped with a 3-wire

grounding-type plug, a plug having a third

(grounding) pin, this plug will only ﬁt into a

grounding-type power outlet. This too, is a

safety feature. If you are unable to insert the

plug into the outlet, contact your electrician to

replace your obsolete outlet. Do not defeat

the safety purpose of the grounding-type plug.

8A.

10.

11.

READ INSTRUCTIONS- All the safety and

operating instructions should be read before

the unit is operated.

RETAIN INSTRUCTIONS- The safety and

operating instructions should be retained for

future reference.

HEED WARNINGS-All warnings on the unit

and in the operating instructions should be

adhered to.

FOLLOW INSTRUCTIONS- All operating and

use instructions should be followed.

CLEANING- Unplug this unit from the wall

outlet before cleaning. Do not use liquid

cleaners or aerosol cleaners.Use a damp cloth

for cleaning.

ATTACHMENTS- Do not use attachments not

recommended by the unit's manufacturer as

they may cause hazards.

WATER AND MOISTURE- Do not use this

unit near water. For example, near a bathtub,

washbowl, kitchen sink, or laundry tub, in a

wet basement, or near a swimming pool.

ACCESSORIES- Do not place this unit on an

unstable cart, stand, tripod, bracket, or table.

The unit may fall, causing serious injury, and

serious damage to the unit. Use only with a

cart, stand, tripod, bracket, or table recom-

mended by the manufacturer.

REMOTE CONTROL

Before using the remote control transmitter, batteries must ﬁrst be installed into it.

2. Install two "AAA" (penlight size) batteries.

3. Replace the battery compartment cover.

Use two "AAA" size penlight batteries (not

supplied) for the transmitter.The batteries may

last approximately one year depending on how

much the remote control is used. For best

performance, it is recommended that batteries

should be replaced on a yearly basis, or when

the remote operation becomes erratic. Do not

mix old and new batteries or diﬀerent types.

BATTERY PRECAUTIONS

These precautions should be followed when

using batteries in this device:

1. Use only the size and type of batteries

specified.

2. Be sure to follow the correct polarity when

installing the batteries as indicated in the

battery compartment. Reversed batteries

may cause damage to the device.

3. Do not mix diﬀerent types of batteries

together (e.g. Alkaline and Carbon-zinc) or

old batteries with fresh ones.

4. If the device is not to be used for a long

period of time, remove the batteries to

prevent damage or injury from possible

battery leakage.

5. Do not try to recharge batteries not intended

to be recharged; they can overheat and

rupture.

(Follow battery manufacturer's directions.)

1. Open the battery compartment cover.

HOW TO INSTALL BATTERIES

TO USE AC POWER SOURCE

Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug into a

standard 120V 60Hz polarized AC outlet.

POWER SOURCE

NOTE:

1. Never connect the AC line cord plug to other than the

speciﬁed voltage (120V 60Hz). Use the attached

power cord only.

2. If the polarized AC cord does not ﬁt into a non-

polarized AC outlet, do not attempt to ﬁle or cut the

blade. It is the user's responsibility to have an

electrician replace the obsolete outlet.

3. If you cause a static discharge when touching the unit,

and the unit fails to function, simply unplug the unit

from the AC outlet, wait a few minutes, and plug it

back in. The unit should return to normal operation.

Polarized AC Cord Plug

(One blade is wider than

the other.)

The exclamation point within an equilateral triangle

is intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance.

S3126A

PORTABLE CART WARNING

(symbol provided by RETAC)

20.

21.

22.

23.

24.

SLEEP Button - To set the TV to turn oﬀ

after a preset amount of time, press the

SLEEP button on the remote control.

The clock will count down 10 minutes

each time the button is pressed in the

order of 120, 110, 100, ······ 20, 10, 0.

After the sleep time is programmed,

the display will disappear then reappear

momentarily every ten minutes to remind

you the sleep timer function is operating.

To conﬁrm the sleep time setting, press

the SLEEP button once and the remaining

time will be momentarily displayed. To

cancel sleep time, press the SLEEP button

repeatedly until the display turns to 0.

MENU Button - Press to display the On-

Screen menu function.

SET + / – Buttons - Press to select the

desired setting during On-Screen operations.

RESET Button - Press to reset the On-

Screen picture adjustments to their

factory preset positions.

QUICK VIEW Button - This button allows

you to go back to the previous channel

selected by just pressing the QUICK VIEW

button. Press this button again to return to

the channel you were watching.

CALL Button - When you press this

button, the channel number tuned will

appear on the upper right corner of the

screen. Press the button again to remove

display from the screen.

CH (CHANNEL) / Buttons -▲ ▼ Press the

▲ button to change to a higher numbered

channel set into memory. Press the ▼

button to change to a lower numbered

channel set into memory.

ENTER Button - Press to enter or select

information for On-Screen operations.

CH.1/2 Button - Switches between

Channel 1and Channel 2 in the Closed

Caption mode.

TV/CAPTION/TEXT Button - Press this

button to switch between normal TV

and the two Closed Caption modes

(captions and 1/3 of full screen text).

Closed Captioning will display text on

screen for hearing impaired viewers.

10.

11.

12.

13.

14.

POWER Button - Press to turn the TV on.

Press again to turn the TV oﬀ.

Direct Channel Selection Buttons (0-9) -

Allows direct access to any channel.

MUTING Button - To turn oﬀ the sound,

press this button once. The TV will be

silenced and the symbol "MUTING" will

appear on the screen. The muting feature

can be released by pressing the MUTING

button again or one of the VOL ▲ or ▼

button.

VOL (VOLUME) / Buttons -▲ ▼ Press

the button to increase, or the button▲ ▼

to decrease the volume level.

GROUND

CLAMP

ELECTRIC

SERVICE

EQUIPMENT

POWER SERVICE

GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

ANTENNA

LEAD IN

WIRE

NEC-NATIONAL ELECTRICAL CODE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING

CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

S2898A

EXAMPLE OF ANTENNA GROUNDING

AS PER NATIONAL ELECTRICAL CODE

3H40101D E 28.09.99, 10:223

LOCATION OF CONTROLS

This TV can display the channel number, on screen displays and picture adjustments on the

screen in English, Spanish or French.

On-screen language selection (step 3) will automatically appear on the screen when you press

the MENU button initially. Select language to use the other menu options.

NOTE:

If Spanish or French is chosen, the Closed Caption indicators will be in the selected language,

but the Closed Caption text will not be aﬀected by the language selection.

Press the MENU button.

Press the SET + or – button to select the LANGUAGE

mode, then press the ENTER button.

Press the SET + or – button until the " " indicator

points to the desired language: English (ENGLISH),

Spanish (ESPAÑOL) or French (FRANCAIS), then

press the ENTER button.

Press the MENU button again.

CH (CHANNEL) and buttons▲ ▼

Press and release the CH (CHANNEL) or button. The channel automatically stops▲ ▼

at the next channel set into memory. Press and hold the button down to change channels

more quickly.

For proper operation, before selecting channels, they should be set into the TV's

memory. See "To Memorize Channels".

DIRECT CHANNEL SELECTION buttons (0-9) - Press these buttons to select a

channel.The channel number will appear on the upper right corner of the TV screen. If an

invalid channel number is selected, the display will revert to the original channel.

TV MODE DIRECT CHANNEL SELECTION - When the TV/CATV menu option is in the

TV position, all channels can be instantly selected by using two buttons. (For example, to

select channel 2, press "0", then "2". If you press only "2", channel selection will be

delayed for a few seconds). For channels 10 and above, press the 2 digits in order.

To turn on the TV, press the POWER button.

The VOLUME can be adjusted to a desired level by pressing the VOL (VOLUME) or ▲ ▼

button.

The sound level will be indicated on the TV screen by GREEN BARS AND A NUMBER.

As the sound level increases, so do the number of BARS AND THE NUMBER on the

screen. The same is true for decreasing the level.

Set the TV/CATV menu option to the appropriate position. When shipped from the

factory, this menu option is in the CATV setting. See "To Memorize Channels".

TV OPERATION

TV - VHF/UHF channels

CATV - CABLE TV channels

SETTING LANGUAGE

1. EAR (Earphone) Jack - Plug an earphone or monaural headphones with an 1/8 miniplug

into this jack for private listening.

2. Remote Sensor - Signals from the Remote Control unit are received here.

3. POWER Button - Press to turn the TV on or oﬀ.

4. VOLUME ▲ ▼/ Buttons - Press to raise or lower the volume of the sound.

5. CHANNEL ▲ ▼/ Buttons - Press to select a higher or lower numbered channel set into

memory.

CLOSED CAPTION

WHAT IS CLOSED CAPTIONING?

This television has the capability to decode and display Closed Captioned television programs.

Closed Captioning will display text on the screen for hearing impaired viewers or it will translate

and display text in another language.

TO VIEW CLOSED CAPTIONS

Press the TV/CAP/TEXT button on the remote control to switch between normal TV and the

two Closed Caption Modes (Captions and Full Screen Text).

Captions: This Closed Caption Mode will display text on the screen in English or another

language (depending on the setting of the Closed Captions CH. 1/2 button). Generally, Closed

Captions in English are transmitted on Captions Channel 1 and Closed Captions in other

languages are transmitted on Captions Channel 2.

Text: The Text Closed Caption Mode will usually ﬁll 1/3 of full screen with a programming

schedule or other information. After selecting a Closed Caption Mode, it will stay in eﬀect until

it is changed, even if the channel is changed. If the Captions signal is lost due to a commercial

or a break in the signal, the Captions will reappear when the signal is received again. If the

channels are changed, the Captions will be delayed approximately 10 seconds.

The Captions will appear in places on the screen where they will least interfere with the picture,

usually on the bottom of the screen. News programs will usually show three-line Closed

Captions which scroll onto the screen. Most other shows provide two or three lined Captions

placed near the character who is speaking so the viewer can follow the dialogue.

Words in italics or underlined describe titles, words in foreign languages or words requiring

emphasis. Words that are sung usually appear enclosed by musical notes.

For television programs broadcasting with Closed Captions, look in your TV guide for the

Closed Captions symbol (CC).

Press the SET + or – button to select the V-CHIP SET option, then press the ENTER button.

Enter your password using the Direct channel selection buttons.

In the event of entering incorrect password press the RESET button. Then press the

ENTER button.

Enter the same password for conﬁrmation, then press the ENTER button.

Press the SET + or – button to select the V-CHIP option.

Press the ENTER button to select the ON.

Press the SET + or – button to select the TV RATING or MOVIE RATING option. Press

the ENTER button.

Press the SET + or – button to select the desired rating for the applicable video or TV

channel. Press the ENTER button.

7Press the MENU button three times to return to normal TV viewing.

TV-Y

TV-Y7

TV-G

: all children

: 7 years old and above

: childrens program

TV-PG

TV-14

TV-MA

: parental guidance

: 14 years old and above

: 17 years old and above

When you select TV-Y7, TV-PG, TV-14 or TV-MA, press the CALL button to show the

contained rating.

Press the SET + or – button to select the desired item you want. Press the ENTER button to

select the OFF.

: all ages

: parental guidance

less than 13 years old

PG-13

NC-17

SETTING V-CHIP

This TV is ﬁtted with a V-CHIP controller which provides you with channel viewing access

controls and restrictions.

OFF TV-Y7 TV-G TV-14 TV-MA

SET– SET+

TV–Y TV-PG

TV RATING

MOVIE RATING

OFF PG PG-13 R NC-17

SET– SET+

: under 17 years old parental

guidance suggested

: 17 years old and above

: adult only

NOTES:

• The V-Chip function is activated only on programs and tapes that have the rating signal.

• Once you block a program using the V-Chip function, the blocked program cannot be

watched based on the content of the show. When the program starts, the "ENTER

PASSWORD" will appear on the screen. When you want to release the V-Chip temporarily,

enter the password.

If you change the channel or turn oﬀ and on the TV while releasing the V-Chip temporarily,

the V-Chip setting will be resumed.

• When you watch the TV from the cable box or the VCR with the RF Modulator, then you

release the V-Chip temporarily, the V-Chip setting will not be resumed until you turn off the TV.

The TV channel is not used in this case.

• When changing the channel with the cable box or the VCR, approximately 10 seconds will

pass until the program appears.

23 4 5

TV1929

1 32 54

TV1329

LANGUAGE

CH SET

PICTURE

V-CHIP SET

–

ENTER

–

ENTER

FRANCAIS

ENGLISH

ESPAÑOL

LANGUAGE / IDIOMA / LANGUE

CATV mode direct channel selection

When the TV/CATV menu option is in the CATV position, channels can be selected as

follows:

1-9

10-19

20-99

100-125

Press "0" twice, then 1-9 as needed.

Example, to select channel 2, press "002".

Press "0", then remaining 2 digits.

Example, to select channel 13, press "013".

Press the 2 digits in order.

Example, to select channel 36, press "36".

Press the 3 digits in order.

Example, to select channel 120, press "120".

NOTE: If the station being viewed stops broadcasting, the TV will automatically shut oﬀ

after 15 minutes.

• When activating the Closed Captioned Decoder, there will be a short delay before the

Closed Captioned text appears on the screen.

• Closed Captioned text is only displayed in locations where it is available.

• If no caption signal is received, no captions will appear, but the television will remain in

the Caption Mode.

• Misspellings or unusual characters may occasionally appear during Closed Captioning.

This is normal with Closed Captioning, especially with live programs. This is because

during live programs, captions are also entered live. These transmissions do not allow

time for editing.

• When Captions are being displayed, on-screen displays, such as volume and mute may

not be seen or may interfere with Closed Captions.

• Some cable systems and copy protection systems may interfere with the Closed

Captioned signal.

• If using an indoor antenna or if TV reception is very poor, the Closed Caption Decoder

may not appear or may appear with strange characters or misspelled words. In this

case, adjust the antenna for better reception or use an outdoor antenna.

3H40101D E 28.09.99, 10:234

Product specificaties

Merk:	Orion
Categorie:	Televisie
Model:	TV1929

Heb je hulp nodig?

Als je hulp nodig hebt met Orion TV1929 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Televisie Orion

Orion TV-518 SI Handleiding

25 Maart 2024

Orion TV-518 Handleiding

25 Maart 2024

Orion LED1946 Handleiding

28 Oktober 2023

Orion TV32PL690D Handleiding

28 Oktober 2023

Orion TV1929 Handleiding

28 Oktober 2023

Orion LED2262 Handleiding

28 Oktober 2023

Orion TV32LB2000 Handleiding

28 Oktober 2023

Orion LED1961 Handleiding

28 Oktober 2023

Orion 3851 Handleiding

9 September 2023

Orion TV-3789F Handleiding

9 September 2023

Handleiding Televisie

Nieuwste handleidingen voor Televisie

Panasonic Viera TX-L32C2EA Handleiding

2 Mei 2024

Panasonic TY-EW3D2ME Handleiding

30 April 2024

LG 50UR81006LJ Handleiding

26 April 2024

Philips 50PUS7009 Handleiding

25 April 2024

RevolutionHD S37LTD Handleiding

25 April 2024

RevolutionHD S46LTD Handleiding

25 April 2024

RevolutionHD S32LTD Handleiding

25 April 2024

RevolutionHD S42LTD Handleiding

25 April 2024

RevolutionHD S50PTD Handleiding

25 April 2024

LG OLED42C2AUA Handleiding

18 April 2024