NUVO 62/2382 Handleiding

Bekijk gratis de handleiding van NUVO 62/2382 (2 pagina’s), behorend tot de categorie Verlichting. Deze gids werd als nuttig beoordeeld door 3 mensen en kreeg gemiddeld 4.4 sterren uit 7 reviews. Heb je een vraag over NUVO 62/2382 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

FOR YOUR SAFETY

WARNING: BE SURE THE ELECTRICITY TO THE WIRES

YOU ARE WORKING ON IS SHUT OFF; EITHER THE FUSE IS

REMOVED OR THE CIRCUIT BREAKER IS SHUT OFF.

GENERAL

You don’t need special tools to install this xture. Be sure to

follow the steps in the order given. Under no circumstances

should a xture be hung on house electrical wires, nor should

a swag type xture be installed on a ceiling which contains a

radiant type heating system. Read instructions carefully. If you

are unclear as to how to proceed, consult a qualied electrician.

NOTE: Proper wiring is essential for safe operation of this xture.

FIXTURE ASSEMBLY

Carefully remove the xture from the carton and check that

all parts are included as shown in gure. Be careful not to

misplace any of the screws or parts, which are needed to install

this xture.

INSTALLATION

IMPORTANT: Do not attach xture directly to outlet box.

STEP 1: Drill holes and insert plastic mounting anchors (G).

STEP 2: Put the decorative cover (A) behind the circular strap

(B), then secure the circular strap (B) to outlet box with outlet

box screws (C), and secure plastic mounting anchor screws (F)

into the matching hole of circular strap (B).

GROUNDING INSTRUCTIONS

STEP 1: Insert the green grounding screw into the hole with

two raised dimples on the mounting bar. Wrap the ground

wire from the xture (if supplied) around the green grounding

screw, then connect it to ground wire from the outlet box (if not

xed on the outlet box) using a wire connector (not supplied).

If ground wire from the xture is not supplied, wrap the ground

wire (if not xed on the outlet box) from the outlet box around

the green grounding screw and tighten it.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE

POWER SUPPLY WIRES.

STEP 2: Take note of the color of the wire(s) on your xture.

Identify which group your xture wire(s) falls into and connect

the wires according to the directions below:

GROUP A:

Connect to Black House Wire

GROUP B:

Connect to White House Wire

BLACKWHITE

* PARALLEL WIRE (round & smooth)* PARALLEL WIRE (square & ridged)

WHITE OR GREY WITH TRACERWHITE OR GREY WITHOUT TRACER

BROWN, GOLD OR BLACK

WITHOUT TRACER

BROWN, GOLD OR BLACK

WITH TRACER

NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer

wire is square shaped or ridged and the less tracer wire is

round in shape or smooth (seen best when viewed from

wire end.)

STEP 3: Take your xture wire(s) from group A and place evenly

against the black wire from the outlet box. Do NOT twist wires

together before using wire connectors.

STEP 4: Fit a wire connector over the wires and screw the

connector clockwise until you feel rmness.

STEP 5: Try gently to pull the connector off the wires. If you

can pull the connector off, carefully re-do steps 3 and 4 as

above, and check again for a rm connection.

STEP 6: Connect the xture wire from group B to the white

wire from the outlet box in the same manner. Make sure no

bare wires can be seen outside wire connectors.

FINAL ASSEMBLY

STEP 1: After wires are connected, tuck them carefully inside

outlet box. Hold the back plate (E) to the circular strap (B). Secure

the screws (D) into the matching hole of circular strap (B).

CLEANING

To clean, wipe xture with a soft cloth. Clean glass with a mild

soap. Do not use abrasive materials such as scouring pads or

powders, steel wool or abrasive paper.

ORDERING PARTS

Keep this sheet for future reference, and in case you need to

order replacement parts. Be sure to use exact wording from

illustration when ordering parts.

FIGURE

Line art shown may not exactly match the xture enclosed. However, the installations

do apply to this xture.

La ilustración puede no concordar exactamente con la pieza enviada. Sin embargo,

las instalaciones sí aplican para esta pieza.

Les images peuvent ne pas correspondre exactement au luminaire de la boîte.

Par contre, les directives d’installation s’appliquent au luminaire.

INSTALLATION AND SAFETY INSTRUCTIONS

ITEM NO: 62-2380, 62-2381, 62-2382,

62-2385, 62-2386, 62-2387, 62-2390, 62-2391, 62-2392

ARTÍCULO Nº: 62-2380, 62-2381, 62-2382, 62-2385, 62-2386, 62-2387, 62-2390, 62-2391, 62-2392

ARTICLE N°: 62-2380, 62-2381, 62-2382, 62-2385, 62-2386, 62-2387, 62-2390, 62-2391, 62-2392

© Copyright 2025 Satco Products, Inc. 1/25 v1.0

Product specificaties