Netgear GS308PP Handleiding

Bekijk gratis de handleiding van Netgear GS308PP (4 pagina’s), behorend tot de categorie Csavaros gép. Deze gids werd als nuttig beoordeeld door 81 mensen en kreeg gemiddeld 4.9 sterren uit 9 reviews. Heb je een vraag over Netgear GS308PP of wil je andere gebruikers van dit product iets vragen? Stel een vraag

© NETGEAR, Inc., NETGEAR and the NETGEAR Logo

are trademarks of NETGEAR, Inc. Any non‑NETGEAR

trademarks are used for reference purposes only.

Installation Guide

Register with the NETGEAR Insight app

1. Search for NETGEAR Insight and download the latest app.

2. Set up a NETGEAR account if you do not have one.

3. Tap the menu in the upper-left corner.

4. Tap REGISTER ANY NETGEAR DEVICE.

5. Enter the serial number located on the bottom of the switch, or use the

camera on your mobile device to scan the serial number bar code.

6. Tap .GO

The switch is registered and added to your account. You can now view the

switch in the NETGEAR Insight app.

Note: Because this is an unmanaged switch, you cannot congure or manage it

in NETGEAR Insight.

Connect the switch

1. Connect network devices to the ports on the switch.

2. Connect an RJ-45 port on the switch to a network.

Note: In a small ofce or home ofce network, connect the switch to the LAN

port of a router that, in turn, is connected to an Internet modem.

3. Power on the switch.

PoE considerations

The switch prioritizes the PoE+ power that it supplies in ascending port order

(from port 1 to port 8). If the aggregate power requirements of all attached power

devices (PD) exceed the power budget of the switch, the PD on the highest-

numbered port is disabled to make sure that the PDs that are connected to the

higher-priority, lower-numbered ports are supported rst.

The following tables describe the power adapter models that are compatible with

the GS308PP switch and the PoE classes and switch allocations:

Note: The listed total power budget is the maximum power limit for the

switch. Many PDs require less than maximum power, so the aggregate power

requirements are lower than the maximum, allowing all eight PoE ports to be

active simultaneously.

Power adapters and total power budgets for the GS308PP:

Power adapter modelPower adapterTotal power budget

EPS90W 90W83W

EPS130W 130W123W

PoE classes and switch allocations:

Device

class

StandardClass

description

Minimum power

allocated to the

powered device

Range of power

delivered to the

powered device

0PoE and PoE+Default power

(full)

0.44W 0.44W–12.95W

Device

class

StandardClass

description

Minimum power

allocated to the

powered device

Range of power

delivered to the

powered device

1PoE and PoE+Very low

power

4.0W 0.44W–3.84W

2PoE and PoE+7.0W3.84W–6.49WLow power

3PoE and PoE+Mid power15.4W6.49W–12.95W

4PoE+ onlyHigh power30.0W12.95W–25.5W

PoE troubleshooting

Here are some tips for correcting PoE problems that might occur:

• Make sure that the PoE Max LED is off. If the PoE Max LED is solid yellow,

disconnect one or more PoE devices to prevent PoE oversubscription. Start by

disconnecting the device from the highest-numbered port.

• Make sure that the Ethernet cables are plugged in correctly. For each

powered device (PD) that is connected to the switch, the corresponding right

port LED on the switch lights solid green. If the right port LED lights solid

yellow, a PoE fault occurred and PoE halted because of one of the conditions

that are listed in the following table.

PoE Fault ConditionPossible Solution

A PoE-related short circuit occurred on the

port.

The problem is most likely with the attached

PD. Check the condition of the PD or restart the

PD by disconnecting and reconnecting the PD.

The PoE power demand of the PD exceeded

the maximum level that the switch permits,

which is 30.9W.

The PoE current on the port exceeded the

classication limit of the PD.

The PoE voltage of the port is outside the

range that the switch permits.

Restart the switch to see if the condition

resolves itself.

8-port Gigabit Ethernet Unmanaged

High-Power PoE+ Switch with FlexPoE

Model GS308PP

Package contents

• Switch

• Power cord (varies by region)

• Power Adapter (90W)

• Wall installation kit

• Rubber feet

• Mounting ties (for power adapter)

• Rack-mount kit for rack installation

• Installation guideOctober 2019

Sample connections

Router

Internet

PoE VoIP

phone

PoE+

security

camera

Smart

phone

Laptop

Wave 2

Wireless AP

GS308PP

ReadyNAS Internet

PoE+

Ethernet

Product specificaties