Mikrotik D-5G-30D3 Handleiding

Mikrotik Tv-antenne D-5G-30D3

Lees hieronder de 📖 handleiding in het Nederlandse voor Mikrotik D-5G-30D3 (4 pagina's) in de categorie Tv-antenne. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
KJ L M O Q RN P S
Parabolic Dish
Antenna Feed
Feed Bracket
Back Plate
Pole Clamp
Case Holder
RF Cable
Self-Bonding Tape Slice
M8 U-Bolt
M6x20 Bolt
M4x12 Bolt
M4 Wing Nut
M4 Serrated Washer
M6 Nut
M6 Spring Lock Washer
M6 Washer
M8 Nut
M8 Spring Lock Washer
M8 Fender Washer
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
1
1
1
1
1
1
2
2
2
5
4
2
5
5
5
5
4
4
4
ITEM DESCRIPTION QTY
MikroTik Antenna assembly preview
MikroTik Antenna assembly preview back* MikroTik Antenna assembly preview front
A B C D
E F G H I
MikroTik Antenna D-5G-30D3
Quick setup guide and warranty information
Package contents
MikroTik Radio
*The preview is valid if a MikroTik RB900 series outdoor device
(sold separately) is installed.
Installation Guide
0. Items Required
• 10mm Wrench 13mm Wrench • • PH2 Screw Driver •
• This guide is written to be used with a MikroTik RB900 series outdoor
device (sold separately) •
1. Install Back Plate to Parabolic Dish
Install Back Plate [D] to Parabolic Dish [A] using:
[J] M6x20 Bolt x 4 pcs;
[P] M6 Washer x 4 pcs;
[O] M6 Spring Lock Washer x 4 pcs;
[N] M6 Nut x 4 pcs.
Important:
• Back Plate [D] must be aligned respecvely to a bore in the
Parabolic Dish [A] - see Fig. 1;
• M6 Nut [N] ghtening torque must be approximately 5 Nm.
2. Install Antenna Feed
Install Antenna Feed [B] to Parabolic Dish [A] using:
[C] Feed Bracket x 1 pc;
[K] M4x12 Bolt x 4 pcs;
[M] M4 Serrated Washer x 4 pcs.
Install grounding fasteners:
[L] M6 Wing Nut x 1 pc;
[M] M4 Serrated Washer x 1 pc.
Important:
• Antenna Feed [B] and Feed Bracket [C] must be aligned respecvely
to the alignment bore in the Parabolic Dish [A] - see Fig. 2;
• M4x12 Bolt [N] ghtening torque must be approximately 2 Nm.
3. Install Pole Clamp
Install Pole Clamp [E] to Back Plate [D] - see Fig. 3, using:
[J] M6x20 Bolt x 1 pc;
[P] M6 Washer x 1 pc;
[O] M6 Spring Lock Washer x 1 pc;
[N] M6 Nut x 1 pc.
Important:
• Do not ghten M6 Nut [N] firmly unl step 7.
FIG. 1
N
O
P
A
D
J
FIG. 2
L
C BMK
FIG. 3
J E O ND P
D
FIG. 4.2FIG. 4.1
M3x8FL
4. Aach MikroTik Radio to Back Plate
Aach a to Case Holder [F] using:MikroTik RB900 series outdoor device
[-] M3x8 Bolt x 4 pcs (Comes with MikroTik Radio) - see Fig. 4.1.
Aach Case Holder [F] to Back Plate [D] by fing Case Holder’s hinges
into the Back Plate’s flange - see Fig. 4.2. Secure Case Holder using:
[L] M4 Wing Nut x 1 pc.
Important:
• M3x8 Bolt [-] ghtening torque must be approximately 1.5 Nm.
H
V
FIG. 5
H
G
Ø = 70mmMAX FIG. 6
R QI S
FIG. 7
Q N D
5. Install RF Cables
Remove the cover from MikroTik Radio and install the RF Cables [G].
Connect vercal polarizaon (arrow V) to CH0, horizontal polarizaon
(arrow H) to CH1 - see Fig. 5.
Insulate the RF Cable [G] ends which are connected to Antenna Feed [B]
by using: [H] Self-Bonding Tape Slice x 2pcs.
• Remove the plastic liner from both sides;
• Stretch the tape to 2/3 of its width;
• Apply half-lapped layers clockwise.
The RF Cable [G] ends which are connected to MikroTik Radio are insulated
by the cover.
Fit back the MikroTik Radio cover.
Important:
• RF Cables [G] connector ghtening torque must be approximately 0.5 Nm.
6. Aach Antenna to Pole
MikroTik Antenna D-5G-30D3 is design to fit the pole diameter up
to 70mm( 2.75”).
Aach MikroTik Antenna to pole as shown in Fig. 6 using:
[I] M8 U-Bolt x 2 pcs;
[S] M8 Fender Washer x 4 pcs;
[R] M8 Spring Lock Washer x 4 pcs;
[Q] M8 Nut x 4 pcs.
Important:
• Do not ghten M8 Nuts [Q] firmly unl step 7.
7. Adjust Azimuth and Elevaon
The Azimuth and Elevaon can be adjusted if M8 Nuts [Q] are slightly
loosen. In order to set the azimuth rotate the antenna around the pole
- see Fig. 7. The elevaon can be set by turning Back Plate [D].
Aer seng the azimuth and elevaon, ghten firmly the corresponding
fasteners - see Fig. 6.
Important:
• M6 Nut [N] ghtening torque must be approximately 5 Nm.
• M8 Nuts [Q] ghtening torque must be approximately 20 Nm.

Product specificaties

Merk: Mikrotik
Categorie: Tv-antenne
Model: D-5G-30D3

Heb je hulp nodig?

Als je hulp nodig hebt met Mikrotik D-5G-30D3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Tv-antenne Mikrotik

Mikrotik

Mikrotik D-5G-30D3-PA Handleiding

26 Augustus 2023
Mikrotik

Mikrotik D-5G-30D3 Handleiding

26 Augustus 2023
Mikrotik

Mikrotik Sleeve30 Handleiding

26 Augustus 2023

Handleiding Tv-antenne

Nieuwste handleidingen voor Tv-antenne

Meliconi

Meliconi AT49 R1 USB Handleiding

30 Maart 2025
Metronic

Metronic 427017 Handleiding

28 Maart 2025
Metronic

Metronic 415047 Handleiding

28 Maart 2025
Metronic

Metronic 416975 Handleiding

27 Maart 2025
Metronic

Metronic 415054 Handleiding

27 Maart 2025
Metronic

Metronic 425031 Handleiding

26 Maart 2025
Astrell

Astrell AST808 Handleiding

26 Maart 2025
Televés

Televés MIRA 5G Handleiding

26 Februari 2025
Televés

Televés BEXIA 5G Handleiding

26 Februari 2025
One For All

One For All SV 9421 Handleiding

19 Februari 2025