Metra AX-TOYCAM2-6V Handleiding

Metra Niet gecategoriseerd AX-TOYCAM2-6V

Lees hieronder de 📖 handleiding in het Nederlandse voor Metra AX-TOYCAM2-6V (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
© COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION © COPYRIGHT 2004-2016 METRA ELECTRONICS CORPORATION
axxessinterfaces.com • metraonline.com axxessinterfaces.com • metraonline.com
Axxess Integrate
®Axxess Integrate
®
REV. 10/10/16 REV. 10/10/16
Installation Instructions for AX-TOYCAM2-6VInstallation Instructions for AX-TOYCAM2-6V
INTERFACE FEATURES
• Retains the factory back-up camera to an aftermarket radio
• Allows an aftermarket camera to be added to the factory screen*
• Includes the AX-CAM6V 12-volt to 6-volt converter
* Display and navigation model radios only
INTERFACE COMPONENTS
• AX-TOYCAM2-6V harness • AX-CAM6V 12-volt to 6-volt converter
AX-TOYCAM2-6V
Toyota Back-Up Camera Retain/Add-On
2006-2013
TOYOTA
4-Runner (with a factory amp) 2012-2013
4-Runner 2006-2011
Avalon 2011-2012
Camry 2007-2011
Highlander 2008-2012
Prius 2010-2011
Sienna 2008-2010
Sequoia (with a factory amp) 2008-2012
Tundra (with a factory amp) 2007-2013
Venza (with NAV) 2009-2012
• Cutting tool • Tape • Crimping tool
• Connectors (example: butt connectors, bell caps, etc.)
APPLICATIONS
TOOLS REQUIRED
CAUTION!
All accessories, switches, climate controls panels, and especially air bag indicator lights
must be connected before cycling the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
K PNOWLEDGE IS OWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
Connections to be made
The AX-TOYCAM2-6V can be connected two different ways
To retain the factory backup camera to an aftermarket radio:
• Connect the Black Black wire to chassis ground and also to the wire of the AX-CAM6V.
• Connect the
Yellow
wire to the
Blue/Red
wire of the AX-CAM6V.
• Connect the reverse wire from the aftermarket radio, to the reverse signal in the vehicle,
and also to the wire of the AX-CAM6V.Blue/White
• Connect the male Yellow RCA jack to the rear camera input of the aftermarket radio.
• Disregard the loose wire, it will not be used in this application.Green/Purple
To allow an aftermarket camera to be added to the OEM screen:
• Connect the Black wire to the ground wire of the aftermarket camera.
• Connect the power wire of the aftermarket camera to accessory power.
• Tape off and disregard the Yellow wire, it will not be used in this application.
• Connect the female Yellow RCA jack to the aftermarket camera.
• The AX-CAM6V 12-volt to 6-volt converter will not be used in this application.
The following (2) steps are only required if a wire
is present in the factory harnessnot
.
•
If a wire is not present in pin-5 of the 5-pin
connector of the factory radio, unplug the
connector, and then insert the metal pin
of the loose wire into it. Green/Purple
Connect the harness back into the radio
.
•
Connect the other end of the loose Green/
Purple wire to the reverse wire of the vehicle
.
1 2 3 4 5
This is the wire view of the
connector in the vehicle
5 Pin Harness


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: AX-TOYCAM2-6V

Heb je hulp nodig?

Als je hulp nodig hebt met Metra AX-TOYCAM2-6V stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd