Metra 99-8909 Handleiding

Metra Carkit 99-8909

Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 99-8909 (4 pagina's) in de categorie Carkit. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
Metra. The World’s Best Kits.MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 4/5/18 INST99-8909
I N S TA L L A T I O N I N S T R U C T I O N S
99-8909
KIT FEATURES
• ISO DIN radio provision with pocket
• Painted black with silver trim
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) Pocket • D) • (4) #8 x 3/8” Phillips screws • E) (4) Panel clips
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation ....................................................... 3
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: 70-1761 (non-amplied models)
Antenna Adapter: 40-LX11
Steering wheel control interface: Please visit
axxessinterfaces.com for more information
A B C D E
Subaru Legacy/Outback (all except 2.5i) 2018-up*
*Visit MetraOnline.com for up-to-date vehicle specic applications.
1.800.221.0932
|
MetraOnline.com
2
1. Unclip and remove the trim below the
climate control panel. (Figure A)
2. Remove (2) Phillips screw securing
the climate control panel, then unclip,
unplug, and remove the panel.
(Figure B)
DASH DISASSEMBLY
(Figure B)
(Figure A)
3. Unclip and remove the a/c vent panel.
(Figure C)
Tip! Start from the bottom of the panel
and release the bottom (2) clips rst.
4. Remove (4) Phillips screws securing the
radio, then unclip, unplug and remove
the radio. (Figure D, E)
Continue to Kit Preparation
(Figure C)
(Figure D)
(Figure E)
Upper screws
Lower screws
REV. 4/5/2018 INST99-8909 3
KIT PREPARATION KIT ASSEMBLY
1. Slightly loosen (4) screws securing
the radio. (Figure A)
2. If the vehicle is equipped with Starlink,
remove (4) screws securing the Starlink
module (shaded part in gure A) located
directly below the radio. The module
must be relocated lower in the dash
cavity to retain functionality with the
front speakers. (Figure A)
3. Remove (4) screws securing the lower
module, then remove the module.
(Figure A)
4. Secure the module to the
radio brackets
using the factory screws. (Figure B)
Continue to Kit Assembly
1. Secure the
pocket
to the
radio brackets
using the (4) #8 x 3/8” Phillips screws
provided. (Figure A)
2. Remove the metal DIN sleeve and trim
ring from the aftermarket radio.
3. Slide the radio into the bracket/pocket
assembly, then secure it using the
screws supplied with the radio.
(Figure B)
4. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using the
proper mating adapter from Metra and/
or Axxess. Test the radio for
proper operation.
5. Secure the radio assembly to the dash
using the factory screws.
6. Attach the
(4) panel clips
provided onto
the
radio trim panel
, then snap the
panel over the radio assembly.
7. Reassemble the dash in reverse
order of disassembly to complete the
installation.
(Figure B)(Figure B)
(Figure A)(Figure A)


Product specificaties

Merk: Metra
Categorie: Carkit
Model: 99-8909

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 99-8909 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Carkit Metra

Handleiding Carkit

Nieuwste handleidingen voor Carkit