Havis C-3090-4 Handleiding
Bekijk gratis de handleiding van Havis C-3090-4 (4 pagina’s), behorend tot de categorie Carkit. Deze gids werd als nuttig beoordeeld door 21 mensen en kreeg gemiddeld 5.0 sterren uit 11 reviews. Heb je een vraag over Havis C-3090-4 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/4
INSTALLATION INSTRUCTIONS C- - 3090’s & C 3089’s
COMPUTER LAPTOP MOUNT AND ACCESSORIES
TOOLS NEEDED:
Ratcheting wrench
Standard socket set
Open-end wrench set
Allen wrench set
Screwdriver set
Always!
Read all instructions before installing any Havis, Inc. products.
Check for obstructions (Wire, brake lines, fuel tank, etc.) before drilling any holes!
Use hardware provided with install kit
1. MOUNTING C-3090-3 or 4 & C-3089-3 or 4 to C- TCB’S
Photo #3 on page #2 is a basic assembly
instruction of a C-3090-3 (w/ tilt/swivel)
mounting to a C-TCB-x.
The tilt/swivel assembly, ( , which Photo #1)
comes pre-assembled to the C-3090 from the
factory, will bolt directly to the rotating plate,
using the hardware loosely attached to the
plate. You do not need to unassembled the
tilt/swivel from the C-3090.
Note: Be sure the 2” fender washer is assembled between
the rotating plate and the tilt/swivel assembly.
2. C-3090-1 or 2 & C-3089-1 or 2 MOUNTING TO
VEHICLE TUNNEL PLATES:
The C-3090 will come pre-assembled with
tilt/swivel attached.
Mount trak kit into vehicle.
Place console and C-3090 into desired
position on trak. (Photo #2)
Note: Be sure assembly does not interfere with dash or
console.
Slide ¼-20 hex nuts into slots on side of trak
in location to mount C-3090.
Attach C-3090 to trak using ¼-20 x ½” hex
bolts and washers. Tighten in desired area.
Photo #1
Photo #2
C-3090_INST_6-09.docx6- 09
3. ADJUST C-3090 PLATFORM FOR SPECIFIC LAPTOP:
The C-3090 will need to be adjusted to
properly hold your particular laptop.
Note: Do not adjust the latch on the underside of the
laptop.
Loosen the “L” clamps on the sides of
the C-3090. (Photo #4)
Release the latch on the underside of the
laptop.
Place laptop on top of C-3090 platform
and close the latch.
Open laptop and adjust “L” clamps so
they are firm against inside lip of
computer on the latch side.
Loosen ¼-20 nylock nuts on the plate on underside of laptop assembly and adjust to
width of laptop.
Photo #3
C-3090_INST_6-09.docx6- 09
Adjust “L” brackets to clamp the laptop firm.
Release latch and test for strength. Adjust if necessary.
4. PLATFORM WIDENING INSTRUCTIONS: ( Photo #5)
On larger laptops, it may be necessary to use a different hole pattern on the plate.
Remove (#1 in photo #5) ¼” nylock nuts and washers
Remove bracket and use alternate mounting holes to create a wider (#2 in photo #5)
platform.
5. OPTIONAL SCREEN SUPPORT (C-SS & C- -2): ( SS Photo #6)
With laptop adjusted for C-3090, open screen on computer.
With screen open, remove ¼-20 nylock nut from “L” tab holding laptop.
Loosely attach optional screen support as shown.
Adjust screen support around screen and tighten hardware.
Test screen movement.
Photo #4
#1
#2
Photo #5
Photo #6
Product specificaties
| Merk: | Havis |
| Categorie: | Carkit |
| Model: | C-3090-4 |
| Kleur van het product: | Zwart |
| Compatibele producten: | C-HDM-200 |
Heb je hulp nodig?
Als je hulp nodig hebt met Havis C-3090-4 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Carkit Havis
27 Mei 2024
27 Mei 2024
27 Mei 2024
27 Mei 2024
27 Mei 2024
27 Mei 2024
27 Mei 2024
27 Mei 2024
27 Mei 2024
27 Mei 2024
Handleiding Carkit
- Konig & Meyer
- Motorola
- Jensen
- PNI
- Renegade
- Uniden
- Envivo
- Novus
- HQ
- Alpin
- HTC
- Renkforce
- Veho
- Belkin
- T'nB
Nieuwste handleidingen voor Carkit
3 Juni 2025
3 Juni 2025
3 Juni 2025
2 Juni 2025
19 Mei 2025
7 Mei 2025
27 April 2025
3 April 2025
3 April 2025
3 April 2025