Metra 99-8210 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 99-8210 (5 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/5
Metra. The World’s Best Kits.® MetraOnline.com © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV.7/2/21 INST99-8210
I N S TA L L AT I O N I N S T R U C T I O N S
99-8210
Attention: With the key out of the
ignition, disconnect the negative battery
terminal before installing this product.
Ensure that all installation connections are
secure before cycling the ignition to test
this product.
KIT FEATURES
DIN radio provision with pocket
ISO DIN radio provision with pocket
KIT COMPONENTS
• A) Radio housing • B) ISO brackets • C) ISO trim plate
TOOLS REQUIRED
• Panel removal tool
• Phillips screwdriver
• 10mm socket removal tool
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Assembly
–DIN radio provision with pocket ........................3
–ISO DIN radio provision with pocket ..................3
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: • 70-1761 • TYTO-01
Antenna Adapter: Not required
A B C
Toyota 4-Runner Limited 2003-2009*
*For non-navigation models
Visit for more detailed information about the product and up-to-date vehicle MetraOnline.com
specific applications
386.257.1187
|
MetraOnline.com
2
1. Unsnap and remove trim from around
shifter. (Figure A)
2. Unsnap and remove center console
cover. (Figure B)
3. Unsnap trim ring from around ignition
key cylinder.
4. Remove (1) 10 mm bolt from bottom
right side of panel below steering
column. Unsnap panel and pull away to
gain access behind panel. (Figure C)
5. Remove (1) 10 mm bolt on bottom left
of center panel behind panel below
steering column. (Figure D)
6. Remove (1) 10 mm bolt beneath climate
control behind pocket door.(Figure E)
Unsnap climate control, unplug and
remove climate control. (Figure F)
7. Remove (2) 10 mm bolts beneath radio
behind climate controls. (Figure G)
8. Unsnap and remove entire center panel
around radio.
9. Remove (2) 10 mm bolts securing radio.
Unplug and remove radio. (Figure H)
Continue to Kit Assembly
(Figure B) (Figure F)
(Figure A) (Figure E)
DASH DISASSEMBLY
(Figure D)
(Figure C)
PASSENGER
(Figure G)
(Figure H)
DETAIL
DETAIL
REV. 7/2/2021 INST99-8210 3
DIN radio provision with pocket
1. Remove the metal DIN sleeve from the
aftermarket radio.
2. Slide the sleeve into the radio housing
and secure by bending the metal locking
tabs outward. (Figure A)
3. Slide the radio back into the sleeve until
it clicks in. (Figure B)
4. Locate the factory wiring harness in
the dash. Metra recommends using the
proper mating adapter from Metra or
AXXESS.
5. Re-connect the negative battery
terminal and test the unit for proper
operation.
6. Reassemble the dash in reverse
order of disassembly
ISO DIN radio provision with pocket
1. Remove the metal DIN sleeve and trim
ring from the aftermarket radio.
2. Mount the ISO brackets to the radio
with the screws supplied with the radio.
(Figure A)
3. Slide the radio into the radio housing
until the side clips engage. Snap the
ISO trim plate into the radio housing.
(Figure B)
4. Locate the factory wiring harness in
the dash. Metra recommends using the
proper mating adapter from Metra or
AXXESS.
5. Re-connect the negative battery
terminal and test the unit for proper
operation.
6. Reassemble the dash in reverse order of
disassembly.
(Figure A)
(Figure B)
KIT ASSEMBLY
(Figure B)
(Figure A)


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 99-8210

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 99-8210 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd