Metra 95-8909 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 95-8909 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 14 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
Metra. The World’s Best Kits.MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 4/5/18 INST95-8909
I N S TA L L A T I O N I N S T R U C T I O N S
95-8909
KIT FEATURES
ISO DDIN radio provision
Painted black with silver trim
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) (4) Panel clips
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation ....................................................... 3
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: 70-1761 (non-amplified models)
Antenna Adapter: 40-LX11
Steering wheel control interface: Please visit
axxessinterfaces.com for more information
A B C
Subaru Legacy/Outback (all except 2.5i) 2018-up*
*Visit MetraOnline.com for up-to-date vehicle specific applications.
1.800.221.0932
|
MetraOnline.com
2
DASH DISASSEMBLY
1. Unclip and remove the trim below the
climate control panel. (Figure A)
2. Remove (2) Phillips screw securing
the climate control panel, then unclip,
unplug, and remove the panel.
(Figure B)
(Figure B)
(Figure A)
3. Unclip and remove the a/c vent panel.
(Figure C)
Tip! Start from the bottom of the panel
and release the bottom (2) clips first.
4. Remove (4) Phillips screws securing the
radio, then unclip, unplug and remove
the radio. (Figure D, E)
Continue to Kit Preparation
(Figure C)
(Figure D)
(Figure E)
Upper screws
Lower screws
REV. 4/5/2018 INST95-8909 3
KIT PREPARATION KIT ASSEMBLY
1. Secure the
radio brackets
to the radio
using the screws supplied with the
radio. (Figure A)
2. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using the
proper mating adapter from Metra and/
or Axxess. Test the radio for
proper operation.
3. Secure the radio assembly to the dash
using the factory screws.
4. Attach the
(4) panel clips
provided onto
the
radio trim panel
, then snap the
panel over the radio assembly.
5. Reassemble the dash in reverse
order of disassembly to complete the
installation.
(Figure A)
1. Slightly loosen (4) screws securing
the radio. (Figure A)
2. If the vehicle is equipped with Starlink,
remove (4) screws securing the Starlink
module (shaded part in figure A) located
directly below the radio. The module
must be relocated lower in the dash
cavity to retain functionality with the
front speakers. (Figure A)
3. Remove (4) screws securing the lower
module, then remove the module.
(Figure A)
4. Secure the module to the
radio brackets
using the factory screws. (Figure B)
Continue to Kit Assembly
(Figure B)
(Figure A)


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 95-8909

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 95-8909 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd