Metra 95-5844S Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 95-5844S (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
Metra. The World’s Best Kits.MetraOnline.com © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 9/27/17 INST95-5844S
I N S TA L L A T I O N I N S T R U C T I O N S
95-5844S
KIT FEATURES
ISO DDIN radio provision
Painted silver to match the factory appearance
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 8mm, 7/32” and 9/32” socket wrench
• T-20 Torx driver
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation ....................................................... 3
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: Please visit metraonline.com for
interface options
Antenna Adapter: 40-CR10
A B
Lincoln Navigator 2007-2014
Intended for 4x2 models without factory NAV
1.800.221.0932
|
MetraOnline.com
2
1. Unclip and remove the panel surrounding
the shifter. (Figure A)
2. Remove (2) 9/32” screws from the
bottom of the radio/climate control trim
panel, and then unclip and remove.
(Figure B)
3. Remove (4) 9/32” screws securing the
radio and then remove.
Radio/climate control trim panel disassembly:
4. Remove (4) Torx T-20 screws and remove
the factory pocket/ ashtray assembly
from the factory dash panel. (Figure C)
5. Remove (4) 7/32 screws and remove the
factory climate controls. (Figure C)
6. Remove all the factory button assembly’s
from the factory dash panel. (Figure C)
7. Remove (7) Torx T-20 screws and (4)
push-nuts to remove the center panel
from the factory dash panel. (Figure C)
Continue to Kit Preparation
(Figure B)
(Figure A)
DASH DISASSEMBLY
(Figure C)
REV. 9/27/2017 INST95-5844S 3
1. Place the
radio trim panel
into the
factory dash panel and secure with
the (7) T-20 screws and (4) push nuts
removed in Dash Disassembly. (Metra
recommends a small 8mm socket for
pressing them on). (Figure A)
2. Mount the pocket, climate controls and
buttons to the Metra
radio trim panel
using the factory hardware. (Figure B)
Continue to Kit Assembly
KIT PREPARATION KIT ASSEMBLY
(Figure A)
(Figure B)
(Figure A)
1. Attach the
radio brackets
to the radio
using the screws supplied with the
radio. (Figure A)
2. Locate the factory wiring harness and
antenna connector in the dash, and
complete all necessary connections to
the radio. Metra recommends using the
proper mating adapter from Metra and/
or AXXESS. Test the radio for proper
operation.
3. Secure the radio into the dash opening
using the factory hardware.
4. Snap the
radio trim panel
over the radio
and then reassemble the dash in reverse
order of disassembly.


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 95-5844S

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 95-5844S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd