Metra 95-3023HG Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 95-3023HG (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 2/16/18 INST95-3023HG
I N S TA L L AT I O N I N S T R U C T I O N S
95-3023HG
KIT FEATURES
• ISO DDIN radio provision
• Painted high gloss black
KIT COMPONENTS
• A) Radio trim panel • B) Radio housing • C) Radio brackets • D) Pocket • E) (4) #8 x 3/8” Phillips screws • F) (4) Panel clips
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 9/32” Socket wrench • Cutting tool
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation .......................................................2
Kit Assembly ..........................................................3
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring Harness: TBA
Antenna Adapter: 40-EU55
Steering Wheel Control Interface: ASWC-1
A B DC
Chevrolet Trax 2017-up*
*Visit for up-to-date vehicle specic applications.MetraOnline.com
E
1.800.221.0932
|
MetraOnline.com
2
DASH DISASSEMBLY KIT PREPARATION
1. Unclip and remove the dash panel
surrounding the radio. (Figure A)
2. Unclip and remove the radio trim.
(Figure B)
3. Remove (2) 9/32” screws securing
the radio, then pull down and back to
release the radio. Unplug the connectors
to remove the radio.
4. Unclip and slide off the plastic trim piece
on the top of the radio. (Figure C)
5.
Remove (2) 9/32” screws securing each a/c
vent, then unclip and remove the vents.
Continue to Kit Preparation
Please visit Metraonline.com for
Dash Disassembly illustrations.
Attention! After the sub-dash has been cut,
the factory radio will no longer be able to
be installed.
1. Cut the sub-dash to allow room for the
aftermarket radio. (Figure A)
2. Attach (4)
panel clips
provided with the
kit onto the
radio trim panel
. (Figure B)
Continue to Kit Assembly
(Figure B)
(Figure A)
Remove
shaded areas
“Head On” View
REV. 2/16/2018 INST95-3023HG 3
KIT ASSEMBLY
1. Secure the
radio brackets
to the radio
using the screws supplied with the
radio. (Figure A)
2. Secure the radio assembly to the
radio
housing
using the (4) #8 x 3/8” Phillips
screws provided. (Figure B)
3. Attach the plastic trim piece removed in
dash disassembly to the top of the
radio housing
.
4. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using
the proper mating adapter from Metra
and/or Axxess. Test the radio for proper
operation.
(Figure A) (Figure B)
5. Secure the completed radio assembly,
and the a/c vents, to the dash using the
factory screws.
a. Slide the radio assembly into
the dash.
b. Wiggle the a/c vents in.
c. Secure the now complete assembly
to the dash using the (6) factory
9/32” screws.
6. Reassemble the dash in reverse
order of disassembly to complete the
installation, using the 95-3023HG
radio
trim panel.


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 95-3023HG

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 95-3023HG stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd