Metra 92-3050P Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor Metra 92-3050P (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 12 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
IMPORTANT
Installation Kit
120 90-3050P
Before starting, compare items on your invoice with items
received. Carefully check through packaging material.
If an item is missing, please call:
Crutchfield
Parts Supplied:
Kit Frame
Support Tray
Chevrolet
Revision 12/10/03
Kit assembly instructions are on the following pages.
Page 1 of 3
®
Copyright 2003 Crutchfield Corporation
*120903050P*
Mounting Brackets
Left
Right
(2) Studs (2) 3/8” Nuts
Trimplate
at 1-888-955-6000
FIGURE 2
Shaft Supports
Installation Kit
120 90-3050P
Chevrolet
1. Press posts on trimplate into holes on kit frame to snap
parts together (Figure 1).
2. Use a utility knife to cut out in trimplate to shaft supports
create a DIN opening (Figure 2).
3. Push clips on into slots on rear of kit frame to support tray
secure (Figure 1).
4. Using pliers, break off the tabs on the side mounting
brackets labeled “B” that are shown as shaded (Figure 3).
The “A” tabs must remain.
5. Secure mounting brackets to sides of kit frame with studs
and nuts supplied (Figure 1).
6. Remove DIN sleeve from receiver and slide into opening in
trimplate. Secure sleeve to trimplate by bending the
securing tabs (Figure 4).
7. Slide receiver into sleeve/kit assembly.
DIN Receiver Assembly
2
®
Copyright 2003 Crutchfield Corporation
Securing Tabs
DIN Sleeve
Bend tabs after sleeve
is inside assembly.
FIGURE 1
Trimplate
Kit Frame
Support Tray
Left Mounting Bracket
Stud
Nut
Right Mounting Bracket
FIGURE 3
FIGURE 4
Break off these “B”
(shaded tabs) on both brackets
Tools Required
Utility
Knife
â–˛
Small Flat Blade
Screwdriver
3/8” Socket
Pliers
These “A”
tabs remain
Installation Kit
120 90-3050P
Chevrolet
Spacers
(supplied with
your order)
1. Press posts on trimplate into holes on kit frame to snap parts
together (Figure 1).
2. Push clips on into slots on rear of kit frame to support tray
secure (Figure 1).
3. Using pliers, break off the tabs on the side mounting
brackets labeled “B” that are shown as shaded (Figure 2).
The “A” tabs must remain.
4. Secure mounting brackets to sides of kit assembly with
studs nutsand supplied (Figure 1).
5. Choose the proper spacers (supplied with your order) to
allow receiver nosepiece to extend 1/8” to 1/4” beyond face of
trimplate (Figure 3).
6. Insert receiver shafts (with spacers in place) through openings
in trimplate. Secure receiver and faceplate with shaftnuts
supplied with receiver.
7. Attach control knobs.
1/8” -1/4”
â–˛
â–˛
Spacer
Shaft Receiver Assembly
3
FIGURE 3
Shaftnuts
®
Copyright 2003 Crutchfield Corporation
FIGURE 1
Trimplate
Kit Frame
Support Tray
Left Mounting Bracket
Faceplate
Control Knobs
Tools Required
â–˛
Deep Socket
(size depends upon receiver)
Stud
Nut
Right Mounting Bracket
3/8” Socket
Pliers
FIGURE 2
These “A”
tabs remain
Break off these “B”
(shaded tabs) on both brackets


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 92-3050P

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 92-3050P stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd