Metra 70-5007 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Metra 70-5007 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
Receiver Wiring Adaptor
120 70-5007
Revision 01/31/18
STEP 1 -- MATCH & CONNECT WIRES
*120705007*
IMPORTANT
Before starting, compare items on your invoice with items
received. Thoroughly check packing materials. If an item
is missing, please call Crutchfield at 1-888-955-6000.
Copyright 2018 Crutchfield Corporation
Power Harness
Orange - Illumination
Yellow - 12 Volts Constant Power
Red - 12 Volts Switched Power
White - Left Front Speaker Positive
Violet - Right Rear Speaker Positive
Green - Left Rear Speaker Positive
Gray - Right Front Speaker Positive
Gray/Black - Right Front Speaker Negative
White/Black - Left Front Speaker Negative
Black - Chassis Ground
Violet/Black - Right Rear Speaker Negative
Green/Black - Left Rear Speaker Negative
Orange/White - Dimmer - (Not Used - Tape Off)
Orange/Black - (Not Used - Tape Off)
Blue - Power Antenna
Blue/White - Not Used (tape off)
Match wires below to the matching function of each wire on your receiver (refer to instructions supplied with receiver). The wire colors of your
new receiver may, or may not, match the wire colors of the adaptor. Match adaptor and receiver wires by function, disregarding color.
Your receiver illumination wire could be Orange or Orange/White. As with other wires, match this wire to the illumination wire in this harness
by function, not by color. If your receiver does not have an illumination wire, tape off the illumination wire.
Individually tape off any unused wires.
Make final wiring connections following instructions on the next page.
See amplifier bypass harness application on page 3.
A.
B.
C.
D.
E.
Speaker Harness
Bypass Harness is shown on page 3.
120 70-5007
Page 2
STEP 2 (CONTINUED)
A. Strip wires back 1/2”.
B. Twist wires together and
insert in crimp cap.
C. Squeeze middle of cap
for tight connection.
Copyright 2018 Crutchfield Corporation
STEP 3 -- HARNESS APPLICATIONS
D. Complete crimp connections
for all necessary wires.
E. Be sure to wrap any wires from
the Wiring Adaptor that are
not necessary (wires with no
match from the new receiver)
with electrical tape.
STEP 2 -- CRIMP CONNECTIONS
Tools & Parts
Required
Wire Stripper/Crimp Tool Crimp Caps
Unused Wire (tape over bare wires)
Receiver Wiring Adaptor
Generic Illustration
Generic Illustration
Receiver Wiring Adaptor Connections
A. When ready to install the
receiver, plug the wiring
Adaptor from the new receiver,
or receiver assembly into the
factory radio harness(es) in the
vehicle dash.
Continued
on the next
page.
STEP 3 -- HARNESS APPLICATIONS (CONTINUED)
120 70-5007
Receiver Wiring Adaptor
B. Locate the factory amplifier under the passenger's seat. Disconnect
the wiring harnesses from the amplifier. Connect the bypass
harness between the two factory harnesses as shown.
Copyright 2018 Crutchfield Corporation
Bypass Harness
Bypass Harness
Factory Amplifier
Page 3


Product specificaties

Merk: Metra
Categorie: Niet gecategoriseerd
Model: 70-5007

Heb je hulp nodig?

Als je hulp nodig hebt met Metra 70-5007 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Metra

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd