Mercusys MS110CMP Handleiding
Mercusys
Niet gecategoriseerd
MS110CMP
Lees hieronder de 📖 handleiding in het Nederlandse voor Mercusys MS110CMP (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 5 personen en werd door 3 gebruikers gemiddeld met 4.8 sterren beoordeeld
Pagina 1/3
© 2025 MERCUSYS 7100000114 REV1.2.1
LED Explanation
Note: For simplicity, we will take MS108GP for example. Your product may dier from the depicted.
Switch Explanation
O: Ports run at 1000/100/10 Mbps (100/10 Mbps for MS110P, MS110CP and
MS110CMP) and support PoE power supply up to 100m away.
On: Ports run at 10 Mbps and support PoE power supply up to 250m away.
Extend
O: The PoE Auto Recovery function is disabled.
On: The switch will constantly detect the working status of a PoE powered device (PD).
When the switch nds that the PD works abnormally, the switch will reboot it.
Recovery
O: Ports can transmit data with each other.
On: The isolated ports cannot transmit data with other downlink ports. They can transmit
data only with the uplink ports (port 5 of MS105GP/port 8 of MS108GP/ports 9-10 of
MS110P, MS110CP and MS110CMP).
Isolation
PoE Switch
Quick Installation Guide
DC AP er ow dapter
AC Power Cord
Connection
PC
Ethernet Ports (1-8)
PoE Ports (1-7)
1. PoE ports can also connect to non-PoE devices, but only transmit data.
2. Non-PoE ports (port 5 of MS105GP/port 8 of MS108GP/ports 9-10 of MS110P,
MS110CP and MS110CMP) are recommended to connect to uplink devices like
gateways.
3. Ports 1-2 have higher priority than other ports in transmitting data if network
congestion occurs. It is recommended to connect key network devices (network
cameras, APs, etc.) to ports 1-2 (not for MS110CP or MS110CMP).
Notes:
Internet
IP Camera AP IP Phone
Powered Device (PD)
Power
On: The power is on
O: The power is o
Link/Act
On:
Link present but no activity
Flashing:
Transmitting or receiving data
O:
No link
PoE Status
On:
PoE power provided
O:
No PoE power provided
Note: For MS108GP, the Power LED is on the top right of port 8.
Mercusys hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU,
2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at
https://www.mercusys.com/en/ce/
EU declaration of conformity
General Specications
Specications
IEEE 802.3i, IEEE 802.3u, IEEE 802.3x (for all models)
IEEE 802.3ab, IEEE 802.1p (only for MS105GP and MS108GP)
CSMA/CD. 802.3af/at PD supported
MS105GP:
5 1000 Mbps RJ45 Ports Auto-Negotiation/Auto MDI/MDIX
PoE Ports: Port 1–4
MS108GP:
8 1000 Mbps RJ45 Ports Auto-Negotiation/Auto MDI/MDIX
PoE Ports: Port 1–7
MS110P:
10 10/100 Mbps RJ45 Ports Auto-Negotiation/Auto MDI/MDIX
PoE Ports: Port 1–8
MS110CP/MS110CMP:
8 10/100 Mbps RJ45 Ports Auto-Negotiation/Auto MDI/MDIX
2 1000 Mbps RJ45 Ports Auto-Negotiation/Auto MDI/MDIX
10BASE-T: 2-pair UTP/STP (≤100m) of Cat. 3 or above
100BASE-TX: 2-pair UTP/STP (≤100m) of Cat. 5 or above
1000BASE-T: 4-pair UTP/STP (≤100m) of Cat. 5e or above
(except for MS110P)
MS105GP: 10 Gbps
MS108GP: 16 Gbps
MS110P: 2 Gbps
MS110CP/MS110CMP: 5.6 Gbps
Store-and-Forward
Automatically learning, automatically aging
External Power Adapter
Input:
NV models: 220-240 VAC, 50/60 Hz
UN models: 100-240 VAC, 50/60 Hz
Output:
MS110CMP: 54 VDC/2.22 A
Other models: 53.5 VDC/1.31 A
MS110CMP: 115 W (up to 30 W for each PoE port)
Other models: 65 W (up to 30 W for each PoE port)
CE, RoHS
Standard
Interface
Protocol
Frequently Asked Questions (FAQ)
The Power LED should be lit when the power system is working normally. If the Power
LED is not lit, please check as follows:
A1:
Make sure the AC power cord/power adapter is connected the switch with power
source properly.
A2:
Make sure the voltage of the power supply meets the requirements of the input
voltage of the switch.
A3:
Make sure the power source is on.
Q1. Why is the Power LED not lit?
It is recommended that you check the following items:
A1:
Make sure that the cable connectors are rmly plugged into the switch and the
device.
A2:
Make sure the connected device is turned on and working well.
A3:
The cable must be less than 100 meters long (328 feet). If Extend Mode is enabled,
it should be less than 250 meters (820 feet).
Q2. Why is the Link/Act LED not lit when a device is
connected to the corresponding port?
When the total power consumption of connected PoE devices exceeds the maximum,
the PoE port with a smaller port number has a higher priority. The system will cut o
power to the ports with larger port numbers to ensure supplying to other ports.
Take MS108GP as an example. If port 1, 2 and 4 are consuming 18 W respectively, and
an additional PoE device with 15 W is inserted to port 3, the system will cut o the
power of port 4 to compensate for the overload.
Q3. Why are PoE ports not supplying power for PoE devices?
A1:
Before upgrading a connected PoE powered device (PD), disable PoE Auto
Recovery to avoid the PD’s damage.
A2:
When a PD does not send data packets to the switch for a long period in certain
scenarios (e.g. an IPC in sleep mode), disable PoE Auto Recovery to avoid the PD
repeatedly rebooting.
Q4. What should I notice before using the PoE Auto Recovery
feature?
Network Media (Cable)
Switching Capacity
Power Supply
Forwarding Method
MAC Address Learning
PoE Budget
Environmental and Physical Specications
CE, RoHS
-10˚C to 40˚C (14˚F to 104˚F)
-40˚C to 70˚C (-40˚F to 158˚F)
10% to 90% non-condensing
5% to 90% non-condensing
Certication
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Mercusys hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Electromagnetic Compatibility
Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.
The original UK declaration of conformity may be found at
https://www.mercusys.com/support/ukca/
UK declaration of conformity
For technical support, replacement services, user guides, and other information,
please visit https://www.mercusys com/support/..
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service,
please contact us.
Place the device with its bottom surface downward.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
The plug on the power supply cord is used as the disconnect device, the
socket-outlet shall be easily accessible.
The PoE ports shall not be used to charge lithium batteries or devices supplied by
lithium batteries.
The socket-outlet shall be near the equipment and shall be easily accessible.
Plug the product into the wall outlets with earthing connection through the power
supply cord.
For MS110CMP only:
Certication
This is a class A product. In a domestic environment, this product may cause radio interference,
in which case the user may be required to take adequate measures.
CE Mark Warning
BSMI Notice
安全諮詢及注意事項
請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
注意防潮，請勿將水或其他液體潑灑到本產品上。
插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
請不要私自拆開機殼或自行維修，如產品有故障請與原廠或代理商聯繫。
警告：為避免電磁干擾，本產品不應安裝或使用於住宅環境。
限用物質含有情況標示聲明書
單元
Ｕnit
PCB
外殼
電源供應器
其他及其配件
限用物質及其化學符號
備考1.〝超出0.1 wt %〞及〝超出0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準值
Note 1：“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of
the restricted substance exceeds the reference percentage value of presence condition.
備考2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。
Note 2：“○” indicates that the percentage content of the restricted substance does not exceed
the percentage of reference value of presence.
備考3.〝－〞係指該項限用物質為排除項目。
Note 3：The “－” indicates that the restricted substance corresponds to the exemption.
○ ○ ○ ○ ○
鉛
Lead
(Pb)
○
○
-
-
汞
Mercury
(Hg)
○
○
鎘
Cadmium
(Cd)
○
○
六價鉻
Hexavalent
chromium
（Cr
+6
）
○
○
多溴聯苯
Polybrominated
biphenyls
(PBB)
○
○
多溴二苯醚
Polybrominated
diphenyl ethers
(PBDE)
○
○
○ ○○○○
Wall Mounting Specications
4#, (5#), 6#, 8#
Screw Standard of
ANSI B1.1
4#, (5#), 6#
MS105GP
Model
MS108GP
4#, (5#), 6#
MS110P
7mm
Minimum Length
of Screw
7mm
7mm
1.5mm
Screw-Head-to-Wall
Minimum Distance
1.5mm
1.5mm
39mm
Wall-Mounting-Holes
Distance
105mm
105mm
4#, (5#), 6#MS110CP 7mm 1.5mm 105mm
4#, (5#), 6#MS110CMP 7mm 1.5mm 105mm
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами України.
The POE output cannot be used to charge lithium batteries or devices with lithium batteries.
Points de collecte sur www.quefairedemesdechets.fr
Privilégiez la répara�on ou le don de votre appareil !
À DÉPOSER
EN MAGASIN
À DÉPOSER
EN DÉCHÈTERIE
OU
FR
Cet appareil
et ses accessoires
se recyclent
E
xplana on of the symbols on the product label�
S
ymbols may vary from products The label is at the bottom of the product..
Symbol
Explanation
Cla ss II equipment
Cla ss II equipment with functional earthing
Alternating current
Direct current
Pol a rity of d.c. power connector
For indoor use only
Dangerous voltage
Cauti on, risk of electric shock
Ene rgy e ciency Ma rking
Protecti ve earth
Ea rth
Fra me or chassis
Fu nctional earthing
Cauti on, hot surface
Cauti on
Opera tor's manual
Stand-by
"ON"/"OFF" (push-push)
Fu se
Fuse is used in neutral N
Cauti on, avoid listening at high vol ume levels for l ong periods
Di sconnection, all power plugs
m
Switch of mini-gap construction
µ
Switch of micro- gap construction (for US version)
Switch of micro-gap / micro
-
disconnection construction
(for other versions except US)
ε
Switch without contact gap (Semiconductor switching device)
RECYCLING
This product bears the selective sorting symbol for Waste
electrical and electronic equipment (WEEE). This means that
this product must be handled pursuant to European directive
2012/19/EU in order to be recycled or dismantled to minimize its
impact on the environment.
User has the choice to give his product to a competent recycling
organization or to the retailer when p3-he buys a new electrical or
electronic equipment.
Product specificaties
| Merk: | Mercusys |
| Categorie: | Niet gecategoriseerd |
| Model: | MS110CMP |
Heb je hulp nodig?
Als je hulp nodig hebt met Mercusys MS110CMP stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Mercusys
6 Juni 2025
6 Juni 2025
6 Juni 2025
3 Juni 2025
3 Juni 2025
3 Juni 2025
25 Februari 2025
24 December 2024
23 December 2024
6 November 2024
Handleiding Niet gecategoriseerd
- Niet gecategoriseerd Alpine
- Niet gecategoriseerd Valeton
- Niet gecategoriseerd CAD Audio
- Niet gecategoriseerd Tracer
- Niet gecategoriseerd Arkon
- Niet gecategoriseerd Gefen
- Niet gecategoriseerd Baracuda
- Niet gecategoriseerd Challenge Xtreme
- Niet gecategoriseerd TranzX
- Niet gecategoriseerd Ozone
- Niet gecategoriseerd Galanz
- Niet gecategoriseerd Avocor
- Niet gecategoriseerd Ctek
- Niet gecategoriseerd Aconatic
- Niet gecategoriseerd Hooker
Nieuwste handleidingen voor Niet gecategoriseerd
7 Juni 2025
7 Juni 2025
7 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025
6 Juni 2025