McIntosh WS350 Handleiding

McIntosh Speaker WS350

Bekijk gratis de handleiding van McIntosh WS350 (4 pagina’s), behorend tot de categorie Speaker. Deze gids werd als nuttig beoordeeld door 124 mensen en kreeg gemiddeld 5.0 sterren uit 62.5 reviews. Heb je een vraag over McIntosh WS350 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/4

McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 FPhone: 607-723-3512 AX: 607-724-0549

Installation

Guide

WS320

WS350

In-Wall Loudspeaker Systems

WS320 WS350

The WS320 and WS350 In-Wall Loudspeaker Systems re-

quire at least 3-3/4 inch of wall depth, including the wall-

board. They can be mounted into a wall surface with a

thickness between 3/8 inch and 1 inch.

Tools and Fasteners Required:

Phillips Screwdriver Tape Measure

Drywall Saw or Knife Stud Finder

Pencil Bubble Level

Cable Ties

Parts Included:

Loudspeaker Baffle (1) Baffle Box (1)

Frame (1) Frame Gaskets (2)

Grille (1) Grille Fasteners (10)

Cutout Template (1) Painting Mask (1)

Clamping Pieces (2) Baffle Washers #8 (6)

Airtight Electrical Connector (1)

Frame Screws #10-24 x 3 inch (6)

Baffle Screws #10-24x 1-1/2 inch (6)

Optional Part:

RK320 Rough-In Bracket (designed to provide a cutout

and mounting frame for installation during new construc-

tion).

Use of Paint Mask

Set the Paint Mask between the baffle and grille to paint

the grille and frame without getting paint on the baffle and

Loudspeaker Elements.

Installing the Frame

The Frame Assembly consists of the frame and two clamp-

ing pieces, held together with six 3 inch screws. These

screws are fully extended to allow pushing the clamping

pieces toward each other so the whole assembly fits into

the cutout.

Note: If the optional RK320 Rough-In Bracket has already

been installed, go directly to step 3.

1. Hold the supplied cutout template against the wall and

align it using the bubble level. Tape the aligned tem-

plate to the wall and trace the opening on the wall.

2. Cut out and remove the piece of wallboard. Pull

enough Loudspeaker Cable to be able to connect it to

the Loudspeaker Baffle while the baffle is still out of

the wall.

3. Install the two L Shaped self adhesive Frame Gas-

kets to the rear of the frame so that it will be between

the frame and the wall. Insert the right side of the as-

sembly into the hole and push it to the right. This will

give enough room to insert the left side of the assembly

into the wall. Center the assembly in the opening.

4. Push the right side Clamping Piece up against the

backside of the wallboard. Tighten the now protruding

center screw enough to gently hold the frame in place.

Repeat on the other side of the frame.

5. Use the bubble level to assure the frame is correctly

positioned, and then tighten all the screws until the

frame is securely attached to the wallboard.

Note: To avoid crushing the wallboard, do not over tighten the

screws. If the mounting position places the frame near a

stud, remove the clamping piece and secure the frame

directly to the stud, through the provided holes.

Installing the Baffle Box

Before setting the Baffle Box into the frame, run the Loud-

speaker Wire through the supplied Airtight Electrical Con-

nector and tighten the connector onto the Loudspeaker

Cable. Be sure to pull enough wire through the connector

to allow connection to the crossover network on the back

of the Loudspeaker Baffle while it is still out of the wall.

Set the Baffle Box into the frame.

Note: The Baffle Box may be positioned with the Airtight

Electrical Connector either at the top or bottom.

Connecting the Loudspeaker

The McIntosh WS320 and WS350 In-Wall Loudspeaker

Systems utilize Binding Posts for Loudspeaker Cable Con-

nections.

1. Connect a Loudspeaker Cable from the black or nega-

tive Loudspeaker Binding Post on the back of the

Loudspeaker Baffle to the negative or common output

terminal of one channel of the amplifier.

2. Connect a Loudspeaker Cable from the red or positive

Loudspeaker Binding Post on the back of the Loud-

speaker Baffle to the positive or 4 ohm output terminal

of the same channel of the amplifier.

Note: Be sure to tighten the Loudspeaker and Amplifier

Binding Posts after connecting.

Installing the Loudspeaker Baffle

Place the Loudspeaker Baffle into the frame/box assembly

and screw it into place using the six supplied screws. Hold

the baffle in place until at least two screws are properly se-

cured.

Note: Secure excess Loudspeaker Cable away from woofer

cone with cable ties.

Installing the Grille

Press onto each Loudspeaker Grille the supplied Rubber

Grille Fasteners, with three per side, two on the top and

bottom edges of the grille. Press the perforated metal grille

into the gap between the baffle and frame. Press all around

the edge until the grille sits flush with the frame.

Installing the Loudspeaker

Rear View

Bottom (or Top)View

Baffle Screws Airtight Electrical Connector

Product specificaties

Merk:	McIntosh
Categorie:	Speaker
Model:	WS350
Gewicht:	11300 g
Breedte:	355 mm
Diepte:	93 mm
Hoogte:	597 mm
Connectiviteitstechnologie:	Bedraad
Gemiddeld vermogen:	250 W
Equalizer-instellingen:	Nee
Aanbevolen gebruik:	Overige
Impedantie:	4 Ohm
Audio-uitgangskanalen:	1.0 kanalen
Speaker plaatsing:	Inbouw in de muur/plafond
Woofer:	Ja
Frequentiebereik:	60 - 32000 Hz
Gevoeligheid:	85 dB
Luidspreker soort:	3-weg
Diameter woofer:	8 "
Diameter hogetonenluidspreker:	1 "
Aantal tweeter drivers:	5
Aantal mid-range drivers:	1
Diameter mid-range driver:	4 "
Tweeter:	Ja
Crossover frequentie:	1500 Hz