MB Quart MBQ-CAM-1 Handleiding
MB Quart
Niet gecategoriseerd
MBQ-CAM-1
Bekijk gratis de handleiding van MB Quart MBQ-CAM-1 (8 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 147 mensen en kreeg gemiddeld 4.4 sterren uit 74 reviews. Heb je een vraag over MB Quart MBQ-CAM-1 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/8
MBQ-CAM-1
Auxiliary Camera
Installation
Guide
CAUTION
Always consider consulting a professional installer before installing
any components. Be careful and take your time. Do not let wires
make contact with metal edges or hot engine components.
Congratulations on your choice of a MB Quart Auxiliary
Camera. This “Quick Start” Installation guide is meant to
help you complete a basic installation. Visit our website at
MBQuart.com for more detailed information.
Disconnect the negative battery terminal from the negative battery post
before installing.
MOUNTING LOCATION
Locate your desired switch and camera location. Mount the switch in
an open carling knockout. If you do not have an open carling knockout,
the unit itself requires a 0.83 inch (21mm) wide by 1.4 inch (37mm)
high opening with at least 2.5 inches of clearance behind the mounting
surface.
WIRE ROUTING
• Route wiring labeled P2,P3,P7 to the switch location.
• Route purple reverse wire and yellow RCA video cables to the
source unit/display.
• Route white 4 pin JST connector to the camera
mounting location.
• Route 12v, ACC, and GND wires to the vehicle battery or buss bar.
CAMERA FLUSH MOUNTING
7KHFDPHUDFRPHVZLWKWKHÀXVKPRXQWDOUHDG\DWWDFKHG
(shown EHORZ,I\RXULQVWDOOORFDWLRQGRHVQ¶WDOORZIRUÀXVKPRXQWLQJ
please see surface mounting instructions on page 2.
7RÀXVKPRXQWWKHFDPHUDXVHWKHVXSSOLHGPPKROHVDZWRGULOO
the hole, making sure there is adequate room behind the panel.
Camera/Switch Installation
CAMERA SURFACE/BRACKET MOUNTING
To surface mount the camera, using the supplied bracket, unscrew
WKHÀXVKPRXQWWULPULQJWKDWFRPHVRQWKHFDPHUD1H[WVFUHZ
on the surface mount bracket. Secure the bracket to the mounting
location you have chosen.
Note - may need to attach bracket to vehicle panel prior to attaching to camera.
WIRING CONNECTIONS
Connect the white 4pin JST from the camera to the camera harness.
At this time you will connect the yellow RCA to the camera input of
your source unit or GMR7V1. Connect your camera’s reverse wire to
the camera trigger input on the radio. (See wiring diagram on page 4)
After all this is done, you can now connect the +12v, ACC, and GND
wires to the buss bar or battery and reconnect the negative battery
terminal to the negative battery post.
Camera/Switch Installation
Product specificaties
| Merk: | MB Quart |
| Categorie: | Niet gecategoriseerd |
| Model: | MBQ-CAM-1 |
Heb je hulp nodig?
Als je hulp nodig hebt met MB Quart MBQ-CAM-1 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd MB Quart
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
Handleiding Niet gecategoriseerd
- Teia
- GoGEN
- Musical Fidelity
- AVPro Edge
- NComputing
- Commercial Chef
- Agfa
- Suevia
- FCC BBQ
- ACE
- Sagem
- Tiptop Audio
- Blafili
- Fannova
- EA Elektro Automatik
Nieuwste handleidingen voor Niet gecategoriseerd
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025
30 Juli 2025