Martin to DMX Converter Handleiding
Martin
Niet gecategoriseerd
to DMX Converter
Bekijk gratis de handleiding van Martin to DMX Converter (8 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 59 mensen en kreeg gemiddeld 4.6 sterren uit 30 reviews. Heb je een vraag over Martin to DMX Converter of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/8
Martin to DMX
Converter
user manual
I
NTRODUCTION
1
Thank you for selecting the Martin to DMX Protocol Converter. This device
employs a unique NMBE algorithm to convert 16 channels of Martin data to 128
channels of DMX data, allowing you to control DMX-only fixtures with Martin’s
3032 and 2510 controllers.
C O N T R O L L E R R E Q U I R E M E N T S
Version 2.08 of the 3032 PC software is required for use with the Martin to DMX
Protocol Converter. This software may be downloaded from the Martin web site at
http://www.martin.dk. No upgrade of the 2510 Controller firmware is required.
S A F E T Y I N F O R M A T I O N
Warning! This product is for professional use only. It is not for
household use.
To prot e ct you r s elf an d o t h e r s fr o m elect r i c s h ock
• Disconnect the fixture from AC power when not in use.
• Always ground (earth) the fixture electrically.
• Use only a source of AC power that complies with local building and electrical
codes and has both overload and ground-fault protection.
• Do not expose the fixture to rain or moisture.
• Do not open or modify the fixture. Refer all service to a Martin service technician.
U N P A C K I N G
The Martin to DMX Protocol Converter comes with:
• 3 m, 3-pin IEC mains cable
• user manual
©2000, 2001 Martin Professional A/S, Denmark. All rights reserved. P/N 35000085, Rev. B
AC Power
3
AC P
OWER
2
Warning! For protection from fire and electric shock, the fixture must be
grounded (earthed). The power supply shall have overload and
ground-fault protection.
Important! Check the voltage setting before applying power!
To i n s t al l a pl u g on t he mai n s l e ad
The mains lead must be fitted with a grounding-type cord cap that fits your
power distribution system. Consult a qualified electrician if you have any
doubts about proper installation.
• Following the cord cap manufacturer’s instructions, connect the yellow and
green wire to ground (earth), the brown wire to live, and the blue wire to neutral.
The table below shows some pin identification schemes.
To s et or ver ify volt ag e sett in g
The Martin to DMX Protocol Converter may be switched between 115 and 230 V.
Verify the voltage setting before applying power.
• Slide the voltage switch located on the side to the voltage setting closest to the
local mains AC voltage.
To a p p l y p o w er
• Verify the voltage setting. Plug the prepared power cord into the mains input
socket and the AC distribution system.
Wire Pin Marking Screw color
brown live “L” yellow or brass
blue neutral “N” silver
yellow/green ground green
Product specificaties
| Merk: | Martin |
| Categorie: | Niet gecategoriseerd |
| Model: | to DMX Converter |
Heb je hulp nodig?
Als je hulp nodig hebt met Martin to DMX Converter stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Martin
30 Juni 2025
21 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
14 Juni 2025
10 Juni 2025
24 Mei 2025
23 Mei 2025
14 April 2025
Handleiding Niet gecategoriseerd
- Profizelt24
- Omnires
- Linear
- Dutchbone
- Tormatic
- Wegman
- Sunlu
- Burigotto
- Neopower
- Philips
- Irradio
- Tycon Systems
- Alogic
- Keurig
- AXESS
Nieuwste handleidingen voor Niet gecategoriseerd
1 Juli 2025
1 Juli 2025
1 Juli 2025
1 Juli 2025
1 Juli 2025
1 Juli 2025
1 Juli 2025
1 Juli 2025
1 Juli 2025
1 Juli 2025