Makita AF353 Handleiding

Makita Nietmachine AF353

Lees hieronder de 📖 handleiding in het Nederlandse voor Makita AF353 (12 pagina's) in de categorie Nietmachine. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

INSTRUCTION MANUAL

Pneumatic Pin Nailer

AF353

ENGLISH: Original instructions

Read before use.

Warning: Please read the instructions and warnings

for this tool carefully before use. Failure to do so could

lead to serious injury.

2 ENGLISH

SPECIFICATIONS

Model: AF353

Air pressure 0.45 - 0.69 MPa (4.5 - 6.9 bar)

Nail length 15, 18, 19, 25, 30, 35 mm

Nail capacity 130 pcs.

Minimum hose diameter 6.5 mm

Pneumatic tool oil ISO VG32 or equivalent

Dimensions (L x W x H) 208 mm x 66 mm x 191 mm

Net weight 0.9 kg

• Duetoourcontinuingprogramofresearchanddevelopment,thespecicationshereinaresubjecttochange

without notice.

• Specicationsmaydifferfromcountrytocountry.

• WeightaccordingtoEPTA-Procedure01/2003

Symbols

Thefollowingshowthesymbolsusedfortheequip-

ment. Be sure that you understand their meaning before

use.

Read instruction manual.

Wear safety glasses.

Thetoolhasthecapabilityofoperatingin

contact actuation mode.

Wear ear protection.

Do not use on scaffoldings, ladders.

Intended use

Thetoolisintendedforfasteningoninteriorworkand

furniture work.

Noise

ThetypicalA-weightednoiseleveldeterminedaccord-

ingtoEN792:

Sound pressure level (LpA):73dB(A)

Uncertainty (K) : 3 dB(A)

Thenoiselevelunderworkingmayexceed80dB(A).

WARNING: Wear ear protection.

Vibration

Thevibrationtotalvaluedeterminedaccordingto

EN792:

Vibration emission (ah):2.5m/s2 or less

Uncertainty(K):1.5m/s2

NOTE:Thedeclaredvibrationemissionvaluehas

been measured in accordance with the standard test

method and may be used for comparing one tool with

another.

NOTE:

Thedeclaredvibrationemissionvaluemay

also be used in a preliminary assessment of exposure.

WARNING:Thevibrationemissionduringactual

use of the power tool can differ from the declared

emission value depending on the ways in which the

tool is used.

WARNING: Be sure to identify safety measures

to protect the operator that are based on an estima-

tion of exposure in the actual conditions of use (taking

account of all parts of the operating cycle such as

the times when the tool is switched off and when it is

running idle in addition to the trigger time).

SAFETY WARNINGS

Pneumatic nailer/stapler safety

warnings

WARNING: WARNING Read all safety warn-

ings and all instructions. Failure to follow the

warnings and instructions may result in serious injury,

electricshockand/orre.

Save all warnings and instruc-

tions for future reference.

For personal safety and proper operation and mainte-

nance of the tool, read this instruction manual before

using the tool.

General safety

Any other use except for intended use of this

tool is forbidden. Fastener driving tools with

continual contact actuation or contact actuation

shall only be used for production applications.

2. Keep ngers away from trigger when not

operating this tool and when moving from one

operating position to another.

3 ENGLISH

3. Multiple hazards. Read and understand the

safety instructions before connecting, dis-

connecting, loading, operating, maintaining,

changing accessories on, or working near

the tool. Failure to do so can result in serious

bodily injury.

4. Keep all body parts such as hands and legs

etc. away from ring direction and ensure

fastener cannot penetrate workpiece into parts

of the body.

5. When using the tool, be aware that the fastener

could deect and cause injury.

6. Hold the tool with a rm grasp and be prepared

to manage recoil.

7. Only technically skilled operators should use

the fastener driving tool.

8. Do not modify the fastener driving tool.

Modications may reduce the effectiveness of

safety measures and increase the risks to the

operator and/or bystander.

9. Do not discard the instruction manual.

10. Do not use a tool if the tool has been damaged.

11. Be careful when handling fasteners, especially

when loading and unloading, as the fasteners

have sharp points which could cause injury.

12. Always check the tool before use for broken,

misconnected or worn parts.

13. Do not overreach. Only use in a safe working

place. Keep proper footing and balance at all

times.

14. Keep bystanders away (when working in an

area where there is a likelihood of through traf-

c of people). Clearly mark off your operating

area.

15. Never point the tool at yourself or others.

16. Do not rest your nger on the trigger when

picking up the tool, moving between operating

areas and positions or walking, as resting

nger on trigger can lead to inadvertent opera-

tion. For tools with selective actuation, always

check the tool before use to ascertain the

correct mode is selected.

17. Only wear gloves that provide adequate feel

and safe control of triggers and any adjusting

devices.

18. When resting the tool, lay it down on the at

surface. If you use the hook equipped with

the tool, hook the tool securely on the stable

surface.

19. Do not operate when under the inuence of

alcohol, drugs or the like.

Projectile hazards

1. The fastener driving tool shall be disconnected

when unloading fasteners, making adjust-

ments, clearing jams or changing accessories.

2. During operation be careful that fasteners

penetrate material correctly and cannot be

deected/misred towards operator and/or any

bystanders.

3. During operation, debris from workpiece and

fastening/collation system may be discharged.

4. Always wear impact-resistant eye protection

with side shields during operation of the tool.

WARNING: It is an employer's responsibility

to enforce the use of safety eye protection

equipment by the tool operators and by other

persons in the immediate working area.

For Australia and New Zealand only

Always wear safety glasses and face shield to

protect your eyes from dust or fastener injury.

Thesafetyglassesandthefaceshieldshould

conformwiththerequirementsofAS/NZS1336.

5. The risks to others shall be assessed by the

operator.

6. Be careful with tools without workpiece con-

tact as they can be red unintentionally and

injure operator and/or bystander.

7. Ensure tool is always safely engaged on the

workpiece and cannot slip.

Wear hearing protection to protect your ears

against exhaust noise and head protection. Also

wear light but not loose clothing. Sleeves should be

buttoned or rolled up. No necktie should be worn.

Operating hazards

1. Hold the tool correctly: be ready to counteract

normal or sudden movements such as recoil.

2. Maintain a balanced body position and secure

footing.

3. Appropriate safety glasses shall be used and

appropriate gloves and protective clothing are

recommended.

4. Appropriate hearing protection shall be worn.

5. Use the correct energy supply as directed in

the instruction manual.

6. This tool has either selective actuation for con-

tact actuation or continuous contact actuation

by actuation mode selectors or is a contact

actuation or continuous actuation contact tool

and has been marked with the symbol above.

Its intended uses are for production applica-

tions such as pallets, furniture, manufactured

housing, upholstery and sheathing.

7.

If using this tool in selective actuation mode,

always ensure it is in the correct actuation setting.

8. Do not use this tool in contact actuation for

applications such as closing boxes or crates

and tting transportation safety systems on

trailers and lorries.

9. Be careful when changing from one driving

location to another.

10.

Always assume that the tool contains fasteners.

11. Do not rush the job or force the tool. Handle

the tool carefully.

Product specificaties

Merk:	Makita
Categorie:	Nietmachine
Model:	AF353

Heb je hulp nodig?

Als je hulp nodig hebt met Makita AF353 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Nietmachine Makita

Makita AF506 Handleiding

10 Juni 2023

Makita AT2550A Handleiding

9 Juni 2023

Makita DBN600ZJ Handleiding

9 Juni 2023

Makita AN613 Handleiding

3 Juni 2023

Makita T221DW Handleiding

2 Juni 2023

Makita T221D Handleiding

22 Mei 2023

Makita GN900 Handleiding

20 Mei 2023

Makita 242077-1 Handleiding

13 Mei 2023

Makita 242094-1 Handleiding

21 April 2023

Makita AN911H Handleiding

15 April 2023

Handleiding Nietmachine

Nieuwste handleidingen voor Nietmachine

Abac G-301 Handleiding

27 Augustus 2024

Ryobi P322 Handleiding

15 Juli 2024

Ryobi P318 Handleiding

15 Juli 2024

Ryobi P317 Handleiding

15 Juli 2024

Ryobi P739 Handleiding

15 Juli 2024

Ryobi P330 Handleiding

15 Juli 2024

Ryobi P360 Handleiding

15 Juli 2024

Rapoo UCA-1014 Handleiding

28 Juni 2024

Milwaukee M18 Fuel 2844-21 Handleiding

25 Juni 2024

DeWalt DPN9033SM-XJ Handleiding

25 Juni 2024