Makita 2012NBX Handleiding
Makita
Schaafmachine
2012NBX
Lees hieronder de 📖 handleiding in het Nederlandse voor Makita 2012NBX (12 pagina's) in de categorie Schaafmachine. Deze handleiding was nuttig voor 50 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/12
1
ENGLISH (Original instructions)
INSTRUCTION MANUAL
DOUBLE INSULATION
IMPORTANT: Read Before Using.
Thicknesser
2012NB
004461
2
ENGLISH (Original instructions)
SPECIFICATIONS
Model 2012NB
Cutting width 304 mm
3.0 mm of stock width less than 150 mm
1.5 mm of stock width from 150 mm to 240 mm Max. cutting depth
1.0 mm of stock width from 240 mm to 304 mm
Feed rate (min-1) 8.5 m
Table size (W x L) 304 mm x 771 mm
No load speed (min
-1) 8,500
Overall length (W x L x H) 483 mm x 771 mm x 401 mm
Net weight 28.1 kg
safety class /II
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
END201-5
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
ï½¥ Read instruction manual.
ï½¥ DOUBLE INSULATION
ï½¥ Only for EU countries
Do not dispose of electric equipment
together with household waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment and its
implementation in accordance with
national law, electric equipment that
have reached the end of their life must
be collected separately and returned to
an environmentally compatible recycling
facility.
ENE001-1
Intended use
The tool is intended for planing wood.
ENF002-1
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
ENF100-1
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects
to the operation of other equipment. With a mains
impedance equal or less than 0.38 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected with
a fuse or protective circuit breaker having slow tripping
characteristics.
ENG905-1
Noise
The typical A-weighted noise level determined according
to EN61029:
Sound pressure level (L
pA) : 86 dB(A)
Sound power level (L
WA) : 99 dB(A)
Uncertainty (K) : 3 dB(A)
Wear ear protection
ENH037-1
For European countries only
EC Declaration of Conformity
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Thicknesser
Model No./ Type: 2012NB
are of series production and
Conforms to the following European Directives:
2006/42/EC
And are manufactured in accordance with the following
standard or standardized documents:
EN12100-1, IEC61029, EN860
The EC Type-Examination Certificate No.
10-SKM-CM-0523
3
The EC Type-Examination per 2006/42/EC was
performed by:
Inspecta Sweden AB
PO Box 30100
SE-104 25 STOCKHOLM, Sweden
Identification No. 0409
The technical documentation is kept by our authorized
representative in Europe who is:
Makita International Europe Ltd,
Michigan, Drive, Tongwell,
Milton Keynes, MK15 8JD, England
3.3.2010
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, JAPAN
ENA001-2
SAFETY INSTRUCTIONS
WARNING! When using electric tools, basic safety
precautions, including the following, should always
be followed to reduce the risk of fire, electric shock
and personal injury. Read all these instructions
before operating this product and save these
instructions.
For safe operations:
1. Keep work area clean.
Cluttered areas and benches invite injuries.
2. Consider work area environment.
Do not expose power tools to rain. Do not use
power tools in damp or wet locations. Keep work
area well lit. Do not use power tools where there is
risk to cause fire or explosion.
3. Guard against electric shock.
Avoid body contact with earthed or grounded
surfaces (e.g. pipes, radiators, ranges,
refrigerators).
4. Keep children away.
Do not let visitors touch the tool or extension cord.
All visitors should be kept away from work area.
5. Store idle tools.
When not in use, tools should be stored in a dry,
high or locked up place, out of reach of children.
6. Do not force the tool.
It will do the job better and safer at the rate for
which it was intended.
7. Use the right tool.
Do not force small tools or attachments to do the
job of a heavy duty tool. Do not use tools for
purposes not intended; for example, do not use
circular saws to cut tree limbs or logs.
8. Dress properly.
Do not wear loose clothing or jewellery, they can
be caught in moving parts. Rubber gloves and
non-skid footwear are recommended when
working outdoors. Wear protecting hair covering to
contain long hair.
9. Use safety glasses and hearing protection.
Also use face or dust mask if the cutting operation
is dusty.
10. Connect dust extraction equipment.
If devices are provided for the connection of dust
extraction and collection facilities ensure these are
connected and properly used.
11. Do not abuse the cord.
Never carry the tool by the cord or yank it to
disconnect it from the socket. Keep the cord away
from heat, oil and sharp edges.
12. Secure work.
Use clamps or a vice to hold the work. It is safer
than using your hand and it frees both hands to
operate the tool.
13. Do not overreach.
Keep proper footing and balance at all times.
14. Maintain tools with care.
Keep cutting tools sharp and clean for better and
safer performance. Follow instructions for
lubrication and changing accessories. Inspect tool
cord periodically and if damaged have it repaired
by an authorized service facility. Inspect extension
cords periodically and replace, if damaged. Keep
handles dry, clean and free from oil and grease.
15. Disconnect tools.
When not in use, before servicing and when
changing accessories such as blades, bits and
cutters.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool
before turning it on.
17. Avoid unintentional starting.
Do not carry a plugged-in tool with a finger on the
switch. Ensure switch is off when plugging in.
18. Use outdoor extension leads.
When tool is used outdoors, use only extension
cords intended for outdoor use.
19. Stay alert.
Watch what you are doing. Use common sense.
Do not operate tool when you are tired.
20. Check damaged parts.
Before further use of the tool, a guard or other part
that is damaged should be carefully checked to
determine that it will operate properly and perform
its intended function. Check for alignment of
moving parts, free running of moving parts,
Product specificaties
| Merk: | Makita |
| Categorie: | Schaafmachine |
| Model: | 2012NBX |
Heb je hulp nodig?
Als je hulp nodig hebt met Makita 2012NBX stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Schaafmachine Makita
19 Juni 2023
15 Juni 2023
6 Juni 2023
26 Mei 2023
22 Maart 2023
23 Februari 2023
19 Februari 2023
9 Februari 2023
29 Januari 2023
19 Januari 2023
Handleiding Schaafmachine
- Schaafmachine Bosch
- Schaafmachine AEG
- Schaafmachine DeWalt
- Schaafmachine WOLF-Garten
- Schaafmachine Bavaria
- Schaafmachine Black Decker
- Schaafmachine Bort
- Schaafmachine Einhell
- Schaafmachine Felisatti
- Schaafmachine Ferm
- Schaafmachine Gamma
- Schaafmachine Gardena
- Schaafmachine Global
- Schaafmachine Gude
- Schaafmachine Hammer
- Schaafmachine Hikoki
- Schaafmachine Hitachi
- Schaafmachine Metabo
- Schaafmachine Parkside
- Schaafmachine Powerplus
- Schaafmachine Protool
- Schaafmachine Rupes
- Schaafmachine Ryobi
- Schaafmachine Skil
- Schaafmachine Stihl
- Schaafmachine Stomer
- Schaafmachine Taurus
- Schaafmachine Topcraft
- Schaafmachine Triton
- Schaafmachine Varo
- Schaafmachine Worx
- Schaafmachine Ozito
- Schaafmachine Black And Decker
- Schaafmachine Cocraft
- Schaafmachine Meec Tools
- Schaafmachine Cotech
- Schaafmachine Fieldmann
- Schaafmachine Mafell
- Schaafmachine Proxxon
- Schaafmachine Porter-Cable
- Schaafmachine Herkules
- Schaafmachine Rikon
- Schaafmachine Surtek
- Schaafmachine Snow Joe
- Schaafmachine Alpha Tools
- Schaafmachine Einhell Bavaria
- Schaafmachine McKenzie
- Schaafmachine Prowork
- Schaafmachine Proviel
- Schaafmachine XU1
- Schaafmachine Ergotools Pattfield
- Schaafmachine Bavaria By Einhell
Nieuwste handleidingen voor Schaafmachine
9 April 2024
9 April 2024
9 April 2024
9 April 2024
9 April 2024
9 April 2024
9 April 2024
9 April 2024
25 Maart 2024
25 Maart 2024