Livex Lighting Brussels 47070-08 Handleiding
Pagina's 1 Engels Verlichting
Bekijk de handleiding van Livex Lighting Brussels 47070-08 gratis online of download de PDF. 11 mensen vonden deze handleiding nuttig. Vraag over dit model? Stel een vraag
ASSEMBLING & INSTALLATION INSTRUCTIONS
The drawing shown may not exactly match the product enclosed. However, the installation
instructions do apply to this product.
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER.
ATTENTION! COUPER LE COURANT AU FUSIBLE OU UN DISJONCTEUR.
ASSEMBLING THE FIXTURE (Fig.1).
1. Shut off the power at the circuit breaker and remove old fixture from ceiling,
including the old mounting plate.
2. Carefully unpack new fixture and lay all the parts on a clear surface.
3. Attach the mounting plate (A) to the junction box using screws (B).The side of
the mounting plate marked “GND” must face out. The junction box is not
included.
4.
While holding the lamp body towards the junction box,guide supply wires
through hole in center of mounting plate. Follow wiring instructions carefully
(see fig.2).
5. Put the lamp body onto the ceiling, aligning the screws on the mounting plate with
the mounting holes on the canopy (C). Lock it securely with the nuts (D).
6. Attach the glass shade (E) and the nut (F) onto the socket of the lamp body, then
securely tighten the nut (F) using the wrench (G), then remove the socket wrench
and save it.
7. Install the light bulb (Not included)in accordance with the fixture specifications.
NOTE: DO NOT EXCEED THE SPECIFIED WATTAGE!
CONNECTING THE WIRES (Fig.2)
1. Take the black wire from the ceiling junction box and the black wire from the
fixture and twist bare ends together. Twist wire connector onto end of wire until
snug.
2. Repeat same process with white junction box wire and white fixture wire. NOTE:
Twist wires together in the same direction you twist the wire connector onto wires.
3. If your junction box has a grounding wire (green or bare copper), attach this wire
and the bare copper wire from the fixture together as step 1. If junction box has
no ground wire, attach the bare copper fixture wire to the green ground screw on
the mounting plate.
4. Tuck the wire connections neatly into the junction box.
Your installation is now complete. Return power to the junction box and test
the fixture.
FIG.1
FIG.2
FIXTURE
WIRES
White or
Ribbed
HOUSE
WIRES
Black (Hot)
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green or Bare
Copper (Ground)
Product specificaties
| Merk: | Livex Lighting |
| Categorie: | Verlichting |
| Model: | Brussels 47070-08 |
Heb je hulp nodig?
Als je hulp nodig hebt met Livex Lighting Brussels 47070-08 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Verlichting Livex Lighting
Livex Lighting Meridian 52136-91 Handleiding Livex Lighting Villa Verona 8578-63 Handleiding Livex Lighting Exeter 2611-04 Handleiding Livex Lighting Arabesque 41113-92 Handleiding Livex Lighting Jefferson 5082-04 Handleiding Livex Lighting Coronado 6121-91 Handleiding Livex Lighting Legacy 5021-01 Handleiding Livex Lighting Oldwick 5715-04 Handleiding
Alle Livex Lighting Verlichting handleidingen
Populair in Verlichting
Livex Lighting Park Ridge 6352-91 Handleiding Livex Lighting 6524-91 Handleiding Livex Lighting Arabesque 41108-91 Handleiding
Handleiding Verlichting
Nieuwste handleidingen voor Verlichting
JMAZ Zona Profile DW Handleiding Tolsen 96222 Handleiding Dainolite CFLED-L1114-WH Handleiding Triton Blue Neptune 300 Handleiding Blizzard HotStik G2 EXA Handleiding Blizzard HotStik G2 RGBALC Handleiding Dainolite BUR-61T-PC-WH Handleiding Dracast Fresnel Studio LED500 Handleiding Beghelli Saving Slim 75465 Handleiding Beghelli Saving Slim 75464 Handleiding